This is the complete AMPro direct replacement front double wishbone set. One order has every single part attached by a small sprue or pin. This comes in SLS Nylon (shown in the video, painted) or MJF which is stronger. We recommend no more than a stock motor be used. Be careful with the cosmetic shock mount as it is very weak in comparison to the structural one. This will work with the stock front springs.

This will not work with the Grasshopper body without significant modifications.

See video before your purchase.

You will need:
1: m3 ball studs (4 of them) with corresponding ball cups (4 of them). 
2. m3 threaded rod for the upper link
3. screw pins with at diameter of 3mm (2 of them, 30mm or longer)
4. M3 self tapping screws (a half dozen or so, no longer than 12mm)
5. 3mm drill bit to chase the printed holes

Stock Replacement Hornet Double Wishbone Front Suspension

45001-00_complete_1-2.stl

045016-A2_1-1_pivot_set.STL

The Tamiya Grasshopper II, Super Hornet, and Rising Fighter have a standard front suspension have the ability to use oil filled shocks which was an improvement on the originals but they suffer from tragic camber gain and bump steer. Not to mention the wobble they create when reversing due to the geometry. We have engineered a total replacement front lower control arm, upright and upper link mount to give these cars a double wishbone front suspension that looks like it was intended to be there. Zero modifications are needed to your bodies and all hardware needed is standard. We have a full installation video (episode 32) on our YouTube channel. and links to pre-printed and STL files are at AMProEngineering.com . 

The front end is shown in images are on the GH2 (white), Super Hornet (silver) and Rising Fighter (red).

All parts needed are attached on one sprue. 

Please see video before purchase:

Parts included are:
045026 0L Left Up.stl
045026 0R Right Up.stl
074002 04 Lower Brace.stl
074002 05 Upper Brace.stl
58074 02 1 1 Left Arm.stl
58074 03 1 1 Right Arm.stl

Super Hornet, Rising Fighter and Grasshopper II Double Wishbone Front Suspension

074002-01_1-1_gh_front_end.stl

This diff lock or spool will replace the spider gears in your CW01/Grasshopper style differential to provide you with a transmission better suited for offroad driving. Both parts are contained in one order. Please see the video before purchase. 

Tamiya CW01 & Hornet Style Transmission Differential Locker / Spool

w01003-00.stl

The Tamiya Grasshopper battery door is not well retained by the chassis so this can result in the door sliding off while driving, and dragging you battery behind you. This is very dangerous and can ruin the battery. This door and retainer will solve that problem. Please see this video for installation prior to purchase as you will need to screw down the retainer.

THIS IS NOT COMPATIBLE WITH THE HORNET. ONE FOR THE HORNET IS AVAILABLE. 

043006-03 1-1 G Batt.stl
043007-01 0-1.Stl



Tamiya Grasshopper Battery Door and Retainer

043006-03_1-1_g_batt.stl

You can now finish off the rear of your Grasshopper 2/Madbull body with a wing that we have developed for them. Please check out the video before purchase as you will need to drill out the location on the body. 

Please note that for both the durable nylon and detailed polyjet prints, you need to prep the screw bosses. The nylon needs to be clean and drilled with a 2.5mm bit and use a self tapping Tamiya screw. The polyjet needs to be drilled with a 2.5mm bit and a bottom tapped M3. 

Grasshopper

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Stock Replacement Hornet Double Wishbone Front Suspension

Super Hornet, Rising Fighter and Grasshopper II Double Wishbone Front Suspension

Tamiya CW01 & Hornet Style Transmission Differential Locker / Spool

Tamiya Grasshopper Battery Door and Retainer

074001-01_1-1_gh_wing.STL