**🧭 Master Control - One Disk To Control it All**

I’m incredibly excited to finally share the Master Control Disk — a project that has taken me months of designing, tweaking, printing, soldering, and refining. It’s easily the most ambitious and satisfying build I’ve ever created.
Smooth lighting, a responsive touchscreen interface, a clean printable shell, and a custom Python program all come together to create a futuristic, functional control surface you can proudly display on your desk.

**✅ Features:**

- 🔵 Dual Addressable LED Rings — vibrant effects, ambient animations, and customizable lighting modes
- 🖥️ Interactive Touchscreen — Waveshare display for menus, widgets, settings, and real-time feedback
- 🐍 Included Python Program — with easy setup script
- 🖨️ Printable 3MF File — parts designed for easy prints and smooth assembly
- 📘 Included Build Guide — wiring, printing, assembly, coding
- 🛠️ Full Parts List — all components required to build the disk from start to finish

**✨ Maker’s Note:**
This project wasn’t simple — you’ll need to learn a bit of electronics, soldering, and programming to bring it to life.
But here’s the fun part: I started this with absolutely no experience in soldering, electronics, or coding, and I still managed to build the entire thing from scratch.
It became one of the most rewarding and genuinely enjoyable learning experiences I’ve had, and I hope it gives you the same sense of challenge, creativity, and accomplishment.

Heads up: this print was made for 256x256 or bigger build plates.

Master Control - One Disk To Control it All

Master Control Base.stl

This is the coolest way to ROCK out the Christmas season! Printed in multiple pieces and assembled separately, this can be a simple seasonal decoration OR it is designed to be a Holiday Radio! All 3mf files included as well as STL files.

Links to assembly videos and Amazon products are included below. Search for the Amazon ASIN to find specific products used. 

Directions:
Printing, you will need - 
1 House 
1 House Back
1 Roof
1 Chimney Snow
1 Door
2 Window Pains
2 Trees (1L, 1R)
8 Gumdrops
33 Lights
2 Candy Twists
1 Candy Twist Knob

Radio:
5W+5W Mini Amplifier Board - Amazon ASIN: B0CQJPPS27 https://www.amazon.com/dp/B0CQJPPS27?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1

2" 4Ohm 3W Full Range Audio Speaker Stereo Woofer Loudspeaker - Amazon ASIN: B01CHYIU26
https://www.amazon.com/dp/B01CHYIU26?ref=ppx_yo2ov_dt_b_fed_asin_title

Mp3 Player Audio Module - Amazon ASIN: B086YLK2XP
https://www.amazon.com/dp/B086YLK2XP?ref=ppx_yo2ov_dt_b_fed_asin_title

Solder
Soldering Iron
Wire
(8) 6x2mm magnets

Watch my video here to guidance on assembly: https://youtu.be/s5stnroZ6jE

- All the small pieces, including magnets attach to house and house back in pre-printed holes/slots. Use a little of your fabvorite glue to hold them together. 
- The trees can be attached in either direction (you will see there is a long side and short side). They were designed that the long side attaches to the front of the house, but either way works.
- I originally attached small pieces of speaker fabric to the window pains, but realized it is much easier to glue the window pains and front door to the house, THEN add a piece of speaker fabric (or any colored fabric) behind the openings to the inside of the house.  there is less trimming required doing it this way. Just lay the fabric on the inside of the house and drop a small dab of CA glue to the 4 corners. 
- Watch A video by Perry Daniels here: https://youtu.be/xFWc0rc6z2A?si=k8WPE99ABQhDyO57 to assemble the MP3 player for the internals of the radio. It is the video that inspired me to build this. Give him a like and subscribe while you're there! 
- The Amplifier board is designed to sit on the shelf and use a glue gun to hold it in place. Speaker fits snuggly in behind the left window and held in with glue gun. The mp3 board can be glued to the base of the house. Remember to place the mp3 board towards the front of the house to ensure you have enough flexibility in the power cord to run through the hole in the House Back. 

If you have ANY questions drop into the Discord listed below! 

Printed in Panchroma Matte PLA
https://us.polymaker.com/products/panchroma-matte

Private Use Only.

Discord for Questions: https://discord.gg/7Fxpk3fkak 

Become a Thangs.com Maker Member for unlimited downloads or become a MERCHANT MEMBER for commercial use. 

Members get priority recommendations and customization. We would love for you to join!
Make sure to like and follow. Post your make so we can see!





Gingerbread House Radio / Decor

Gingerbread Radio - House.stl

Practical print-in-place design who fits an Arduino UNO and a breadboard, ideal for students or nomad makers. If you need an Arduino  or a breadboard, have a look here:

- Breadboard 
1. https://amzn.to/3eojCO9
2. https://s.click.aliexpress.com/e/_Dlyzzvp

- Arduino
1. https://amzn.to/3RLbC8v
2. https://s.click.aliexpress.com/e/_DEVibVZ 

If you want to print the logo in a different color, here you can find some useful information

IF YOU WANT A VERSION WITH CUSTOM LOGO, JUST SEND ME A MESSAGE ;)

ELECTRONICS

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Master Control - One Disk To Control it All

Gingerbread House Radio / Decor

Arduino mobile lab PP