HMG7 Neptune 3 Skirt V2.stl

This STL is a component of the Hero Me Gen7 Printhead assembly for 3D printers.

**Hero Me Gen7 is a modular printhead platform for 3D printers with excellent part cooling and the most compatibility across printers, hotends, extruders, ABLs, and other components.**

 The Hero Me Gen7 is all about choice and personal preference. If you have been upgrading your 3D printer, you've made choices about what is important to you, Your choices are likely going to be different from everyone else. When choosing a hotend, extruder, and ABL combo (not to mention fans and accelerometers), where are you going to find a printhead platform that will accommodate all your selected components (which could be a rare combo), for your specific 3D printer AND provides part cooling that gives you great print results. **This is what the Hero Me Gen7 is all about!**

Think of the Hero Me platform as lego blocks for printheads, there are mounting parts for each component (hotend, extruder, fans, ABLs, etc.) that stack and mount to a core Base. Component specific mounting parts can be interchanged for another of the same type. So, should you change your component selection(s) in the future, you do not have to start over, you simple replace the single STL mount that is matched to the new component. There is no need to yet again go looking for a new set of mounting hardware that was not likely to have been designed to work with each other in the first place.

So to give you choice and fulfill your personal preferences in 3D printing, the Hero Me Gen7.3.2 now supports over 100 3D Printer models (plus clones), 46 Hotends, 34 Extruders (over 45 mount options), 17 ABL Sensors (34 mount options), 35 Part Cooling Duct options, 12 Cable Management options, 11 ADXL345 mounts, and 4 LED bar mounts (among many other options). Gen7.3.2 supports most of the popular 3D printers and components available. 

If you know your 3D printer model, hotend, fans, and optionally an extruder, ABL sensor, ADXL345 accelerometer (for Klipper), and any other options for your printhead assembly, you can scan through the Hero Me Gen7 Release 3.2 folder, or use the Thangs Advanced Search.  Be sure to set the creator filter to: ‘MediaMan3D’ then search for ‘HMG7’ which should bring up all the STLs. You can refine your search from there by component, brand, etc.

If you find that you have a 3D printer model or component that is not yet supported, send me information and preferably a STEP or STL (or link) if you know of one for the X carriage of that printer or the component and I will create a mount for it. Send to: MediaMan3D@gmail.com

If you want Hero Me documentation… The Hero Me Gen7.3.2 folder of STLs on Thangs is organized into sub-folders by component category, with sub—sub-folders for type and brand with well defined filenames to make it easy to find what you need. If you want documentation to help you select and assemble the Hero Me Gen7 for your specific 3D printer, you can get a membership plan here on Thangs.  You will get a detailed 56 page parts selection and illustrated assembly guide along with assembly videos, private Discord server access (with over 2,000 Hero Me users), technical support, and much more, You also get exclusive access to new STL releases 30 days before being posted to Thangs, and other STL libraries. Check out the membership plans here:  [https://thangs.com/designer/mediaman3d](https://thangs.com/designer/mediaman3d)

HMG7.3 Haldis Red Lizard Collar Mount.stl

HMG7 Duct Offset Check v5.stl

This STL is a component of the Hero Me Gen7 Printhead assembly for 3D printers.

**Hero Me Gen7 is a modular printhead platform for 3D printers with excellent part cooling and the most compatibility across printers, hotends, extruders, ABLs, and other components.**

 The Hero Me Gen7 is all about choice and personal preference. If you have been upgrading your 3D printer, you've made choices about what is important to you, Your choices are likely going to be different from everyone else. When choosing a hotend, extruder, and ABL combo (not to mention fans and accelerometers), where are you going to find a printhead platform that will accommodate all your selected components (which could be a rare combo), for your specific 3D printer AND provides part cooling that gives you great print results. **This is what the Hero Me Gen7 is all about!**

Think of the Hero Me platform as lego blocks for printheads, there are mounting parts for each component (hotend, extruder, fans, ABLs, etc.) that stack and mount to a core Base. Component specific mounting parts can be interchanged for another of the same type. So, should you change your component selection(s) in the future, you do not have to start over, you simple replace the single STL mount that is matched to the new component. There is no need to yet again go looking for a new set of mounting hardware that was not likely to have been designed to work with each other in the first place.

So to give you choice and fulfill your personal preferences in 3D printing, the Hero Me Gen7.3.2 now supports over 100 3D Printer models (plus clones), 46 Hotends, 34 Extruders (over 45 mount options), 17 ABL Sensors (34 mount options), 35 Part Cooling Duct options, 12 Cable Management options, 11 ADXL345 mounts, and 4 LED bar mounts (among many other options). Gen7.3.2 supports most of the popular 3D printers and components available. 

If you know your 3D printer model, hotend, fans, and optionally an extruder, ABL sensor, ADXL345 accelerometer (for Klipper), and any other options for your printhead assembly, you can scan through the Hero Me Gen7 Release 3.2 folder, or use the Thangs Advanced Search.  Be sure to set the creator filter to: ‘MediaMan3D’ then search for ‘HMG7’ which should bring up all the STLs. You can refine your search from there by component, brand, etc.

If you find that you have a 3D printer model or component that is not yet supported, send me information and preferably a STEP or STL (or link) if you know of one for the X carriage of that printer or the component and I will create a mount for it. Send to: [MediaMan3D@gmail.com](mailto:MediaMan3D@gmail.com)

If you want Hero Me documentation… The Hero Me Gen7.3.2 folder of STLs on Thangs is organized into sub-folders by component category, with sub—sub-folders for type and brand with well defined filenames to make it easy to find what you need. If you want documentation to help you select and assemble the Hero Me Gen7 for your specific 3D printer, you can get a membership plan here on Thangs.  You will get a detailed 56 page parts selection and illustrated assembly guide along with assembly videos, private Discord server access (with over 2,000 Hero Me users), technical support, and much more, You also get exclusive access to new STL releases 30 days before being posted to Thangs, and other STL libraries. Check out the membership plans here:  [https://thangs.com/designer/mediaman3d](https://thangs.com/designer/mediaman3d)

HMG7.3 Pen Plotter Right Mount.stl

HMG7.2 Orbiter V2.0 Rear Tall Mount V4.stl

HMG7 Orbiter V1.5 Front Mount.stl

HMG7 Longer LK5 Pro Gantry Adapter.stl

HMG7 Dragonfly BMS Bowden Hotend Standoff.stl

HMG7.3 Ender 2 Pro Gantry Clips.stl

HMG7.3 Linear Rail Bottom Belt Bracket V2.stl

HMG7 BMG PTFE Collar Insert B.stl

HMG7 BMG PTFE Collar Insert A.stl

Heart of Mars (Creality Cloud Tool).stl

This is a heart on the planet Mars to be made as a planet lamp. This was done with the Makers Tools on the Creality Cloud mobile app. Worked a treat to design, and as soon as I have time, it will be awesome to print out.
The print went well with no supports and just a brim on the base. I have tested with a torch for the image but have some LED bases ordered to light this up nicely and give it something to sit on.
Printed in Esun Fire Engine Red PLA+ until I ran out (stupid mistake on my part) and finished in Peak Green Esun PLA+ this has made for a weird looking lamp but I’m happy. Only thing I would suggest that I missed in slicing is the Z seam placement, I let it auto hide mine but it is all aligned ( albeit on the side) but it is still a bit annoying.
A cool print regardless and will be fun in my sons Galaxy themed room I hope someone else gets some joy from this. Original at https://www.crealitycloud.com/model-detail/65350fd9f9b64ae4d5a05224
Print took just over 6 hours on the K1 with default settings, took around 154g of filament and was click and go.


HMG7.3 Creality Spider 3 Pro 2-Screw Mount.stl

Creality SparkX i7 D3P bottom riser

Project SparkX i7 Bottom riser 2026-6-7.3mf

Ender-3 V3 Plus Enclosure Clearance Kit

ender3vplus-kit-bed-cable-cover-body-by-ondrahaa.stl

Creality Sprite Extruder BL Touch Adapter

Sprite Extruder BL Touch Adapter - Diystrument.STL

HMG7 Anycubic Vyper - E3DV6 Collar Stock Mount B V2.stl

HMG7.4 4mm Spacer for Skirt Mount.stl

Basalt Column Planter Vase

Basalt Column Planter Vase 088.obj

Creality

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

HMG7 Neptune 3 Skirt V2.stl

HMG7.3 Haldis Red Lizard Collar Mount.stl

HMG7 Duct Offset Check v5.stl

HMG7.3 Pen Plotter Right Mount.stl

HMG7.2 Orbiter V2.0 Rear Tall Mount V4.stl

HMG7 Orbiter V1.5 Front Mount.stl

HMG7 Longer LK5 Pro Gantry Adapter.stl

HMG7 Dragonfly BMS Bowden Hotend Standoff.stl

HMG7.3 Ender 2 Pro Gantry Clips.stl

HMG7.3 Linear Rail Bottom Belt Bracket V2.stl

HMG7 BMG PTFE Collar Insert B.stl

HMG7 BMG PTFE Collar Insert A.stl

Heart of Mars (Creality Cloud Tool).stl

HMG7.3 Creality Spider 3 Pro 2-Screw Mount.stl

Creality SparkX i7 D3P bottom riser

Ender-3 V3 Plus Enclosure Clearance Kit

Creality Sprite Extruder BL Touch Adapter

HMG7 Anycubic Vyper - E3DV6 Collar Stock Mount B V2.stl

HMG7.4 4mm Spacer for Skirt Mount.stl

Basalt Column Planter Vase