Here Is Phone Clamp Car holder V2, This awesome Design is The next iteration in my swivel phone holder series, this design incorporates the same easy to use swivel ball design with a new and improved quick grip phone holder (If your not a fan of this you can use the old Clamp and screw design with this design). There may seem like a lot to choose, but I've labelled everything to make them easy to follow, First select the right hand side cradle and left hand side Labelled RHS and LHS, Next Choose if you want the middle extension I recommend it for most car's, Then Select the Correct size Air vent clip you need, I recommend the Medium size Labelled Air Vent M 20x20, The LN stands for Long neck Useful for Air vents with deep vents, Next Select the Leg stand off's that suit your Car, I recommend the Legs M 9x35.
Assembly, First Push the Spring onto the LHS Cradle Using the Male Connector into the back of the Spring, Then once connected and sitting flat, Slide the spring and LHS cradle into the RHS cradle, They Should push in and click into the notches to remove or change positions, Push down on the top lever of the spring and slide out, Next Connect the RHS cradle to the Middle extension Take your time doing this as the join's are tight I recommend using a heat gun on the female side of the connector before pushing the ball joint in, But you'll only need a little bit of heat, over doing the heat will make the joint loose, Now do the same and join both the cradle and Middle extension to the Joiner with hinge, Once assembled add your legs to the joiner with hinge, Don't use heat for this step and push the male connector into the female side of the hinge it will be tight at first but keep wiggling and pushing until they sit flush, Now simply slide your air vent into the Back of the joiner with hinge, use the arrow pointing into the rail to slide the right direction You might need to add glue inside the rail to hold the Air vent clip In place, But Check the Assembled Phone holder in your car before Gluing, If you want to charge your phone once it's in the cradle simply Push Your cable through the Bottom Hole to connect to your phone. To add your phone into the cradle inert at the top and slide in, then Push down on the top of the spring lever and slide to the right until it clips to the closest Notch, **If your phone is still loose and not clipping into a notch Try the RHS Cradle V2 this Model Has the notches Offset 3.3mm in the other direction which should fit your phone size better,** 
Print setting Nozzle size 0.4mm, Layer Height 0.2mm, Infill 20%, Wall count 3, Supports needed, Support Type Normal, Support Placement Everywhere, Brim No, Rafts No,

Phone Clamp Car holder V2

RHS Cradle.stl

RHS Cradle V2 (use V1 first).stl

Swivle Arm Extension joint V2.stl

Here is Car Phone Holder MagSafe, This awesome Design is a fully customisable adjustable and interchangeable MagSafe phone holder to fit almost any car or phone, If you can't fit your car or phone please leave a comment and I'll try my best to add another part to fit your car. The design is split into 6 parts, selecting them start with the main cradle or if your using larger double sized tape select the main cradle that has an extra 1mmm space, Next select the air vent size I recommend the medium 20x20, The LN stands for Long neck if your vents are further away, Next select your leg sizes I recommend the Medium or small, I've also included a wider hinge joint but I recommend the 24mm, 
Assembly to Joint the adjustable swivel ball joint to the Circle Base, Place them both on a flat table or bench, It's easier on a harder surface like stone or marble, Then Flip the joint upside down and push flat and straight down on the back of the circle joint, they will be quite tight but you'll hear a click when their in place, If your struggling with this step you can heat the circle base up with heat gun or hair dryer then insert the Ball joint, But doing this will make the joint a lot looser, 
Next push the cable through the front of the Main cradle then through the circle base, attach The circle base to the Main cradle after this step.
Next push each of the arms into the Hinge Joint by pushing and wiggling slightly, you'll know their in place when you can clip them into the positioning slots, Now slide the assembled Hinge and stand off legs into the Main cradle, they should easily slide into the right side of the cradle under the circle base.
Next slide the air vent clip over the cable using the cable slot and clip it into the other side, One side will be smaller on the air vent clip this part goes in first, on the smaller air vent clips the arrow will point to the correct direction, 
Next if you're happy that you have the correct parts, insert the Back slide plug into the main cradle If your using PLA the parts should be tight enough without using glue, but if your using PETG you'll need to apply a bit of glue in between the circle base and the main cradle and behind the air vent clip but make sure you do this after you install the MagSafe charger and cable,
Print settings, Nozzle size 0.4mm, Layer Height 0.2mm, print speed 100mms, Supports needed, Support Type Normal, Support Placement touching build plate only, Infill 20%, Wall Count 3, 

Car phone holder

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads