Bed Level Test (Scalable)

Bed Level Test_Ender 5 Pro.3mf

🎲 𝙉𝙤𝙩 𝙩𝙝𝙚 𝙪𝙨𝙪𝙖𝙡 𝙘

Calibration Cube_ICPI.stl

🎲 𝙉𝙤𝙩 𝙩𝙝𝙚 𝙪𝙨𝙪𝙖𝙡 𝙘𝙖𝙡𝙞𝙗𝙧𝙖𝙩𝙞𝙤𝙣 𝙘𝙪𝙗𝙚 🎲

My own version of the popular model used to test out printing tolerances, surface quality and to tune up your slicing profiles for every filament change.

This 20mm calibration cube has almost everything you need to check before actually start your prints: overhangs, bridging, retraction, ghosting, stringing, etc.

You can enjoy making it and have an actual cool, original and good-looking cube!

Join the #𝙞𝙘𝙖𝙣𝙥𝙧𝙞𝙣𝙩𝙞𝙩 challenge , show up your printed cube!

Happy printing everyone! 🎲

⸻⸻⸻⸻⸻⸻⸻⸻

Don't be shy, share your make and be sure to tag @𝙧𝙖𝙣𝙙𝙤𝙢𝙞𝙯𝙮.𝙞𝙩 in your socials!

⸻⸻⸻⸻⸻⸻⸻⸻

𝗜𝗡𝗦𝗧𝗔𝗚𝗥𝗔𝗠 : https://www.instagram.com/randomizy.3d/

𝗖𝗵𝗲𝗰𝗸 𝗠𝗼𝗿𝗲 𝗛𝗲𝗿𝗲 : https://linktr.ee/RandomizY

XYZ_CallibrationCube.stl

This is a small and simple XYZ calibration cube for checking the dimensional accuracy of your printer.   The cube has X, Y and Z written along their respective axes.

Once printed either use an accurate ruler or callipers to measure the dimensions of the print. The original model size is 20mm*20mm*20mm however you may wish to resize it to be bigger (or smaller). 

Once you have measured your dimensions you may want to adjust the steps or steps per mm for each axis in your printers firmware - This may or may not be possible depending on your printer. 

To do this you will need to find your current Steps per mm, and then have your observed dimension and expected dimension.

To calculate the new Steps per mm you will need to do:

(Expected/Observed)*Current Steps per mm = New Steps per mm

It is also good as just giving a gauge of how well your 3D printer works with small over hangs and flat faces to check for Z-Banding or ghosting!

Easy Torture test -Torture Cube

This is a very easy very simple torture test to see the dimensional accuracy of your print and also slightly test your overhangs!!
This is a small ornate "cube" which can be printed in about 30-50mins depending on your settings.
I print one with faces parallel to the axes and then another at a 45 degree angle to test the diagonals of the printer.


Calibrate

Most Downloaded of All Time

Categories

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Bed Level Test (Scalable)

Calibration Cube_ICPI.stl

XYZ_CallibrationCube.stl

Easy Torture test -Torture Cube

Horizontal Expansion Calibration Figures

Ripple Benchy - Test Print