Get your favorite Maker's Mark at RMRRF with the Creator Capsule.
A unique multicolor 3d model designed specifically for capturing autographs and stickers from your favorite Makers, Content Creators, or just a person you admire a lot.
A big thanks to [3DPrintBunny](https://thangs.com/designer/3dprintbunny) for allowing me to use her RMRRF string art as a baseline for the capsule.
All pieces print with .2mm layers except the sheets. The sheets are only .3mm thick. I printed them with a .2mm first then a .1mm on top. You could do three .1mm layers too. 
** This model has fairly tight tolerances, the sheets must NOT be more than .3mm thick**
2 fronts available 4 color blend and an 8 color. The 4 color blend uses a bit of orange under some blue to give the lake a different shade. You can select any colors of course. The color under the lake is the same as the sun and RMRRF. Use the ground over.2 and under.8 files for the 4 color model if using the stls.
8 color gives you more options for creativity. Have fun with it!
The fronts print face down, best to use the 3mf files. I have adjusted the first layer line width to fill in some small gaps. This method has worked well for me with various multicolor prints.
The fronts glue into the case tray, this should be fairly straightforward. I used mini clamps along the side after applying the glue/gloop. Gloop is nice but you gotta move fast. I applied glue in 7 spots along the inside of the case tray and not the front underside, 3 on each side then 1 in the back. Then I slide the front into place, moved it forward then back to spread the glue and seat it fully, then clamped! Let fully cure.
The case top can be tricky to print, use a brim if you need to. I just used some gluestick and all was good.
I mentioned the sheets but will say again .3mm thick!
The capsule holds 20 sheets pretty well, any more than that you risk squishing the springs too much and they may lose there springiness' or break. Feedback on this is appreciated.
I hope you enjoy this model and get those autographs for your memories.


RMRRF Creator Capsule.

rmrrf case front 8color.3mf

**Please read below for information about slicer settings and update log!**

A huge thank you to the M3D Aetas Members for the countless hours of printing and feedback to help make this design come together!

Fantastic Vending Machine is a fully 3d printed surprise capsule machine. This design will see continued improvement and enhancement over time with upgrades such as printable capsules, larger capacity and a token system!

At 100% scale it can use 2” capsules and at 80% scale can use 1.5” capsules. I’ll include links of where you can acquire them down below.
I’ve just about finished the assembly video and I’ll be posting that to YouTube later this evening.

I can’t wait to start seeing everyone’s prints and I really hope you all enjoy the design! My 8 and 13 year olds have both staked claims to multiple of the ones I’ve printed as they just like playing with them! 😂

**Print settings for Hopper Front Screen:**

- Wall Loops: 3
- Top Layers: 0
- Bottom Layers: 0
- Infill Pattern: Honeycomb
- Infill Density: 3%
- Infill Direction: 30

**Print settings for all other files:**

- Use auto supports on Hopper, Tumbler and Tumbler Handle
- 3 Walls, 15% Gyroid

Surprise Capsules:
- Colored Capsules 2” - [https://amzn.to/4deJmqs](https://amzn.to/4deJmqs)
- Clear Capsules 2” - [https://amzn.to/4jVeqyj](https://amzn.to/4jVeqyj)
- Colored Capsules 1.26” - [https://amzn.to/456i97m](https://amzn.to/456i97m)
- Clear Capsules 1” - [https://amzn.to/42Tcv7i](https://amzn.to/42Tcv7i)

Update 06/28:
- Hopper Plug r2 
- Base Bottom r2 (with ramp)
- Add-on Base Bottom Ramp (existing prints)

M3D - Fantastic Vending Machine

Hopper-Front-Screen_standard.stl

FVM-BaseBack_R3.stl

FVM-BaseFront_R3.stl

FVM-BaseFront_r3.stl

FVM-BaseSides_R3.stl

FVM-Hopper-Frame_flush_standard.stl

FVM-Hopper-Plug_R2.stl

FVM-Hopper.stl

FVM-Tumbler-Handle.stl

FVM-Tumbler-Nubs_R3.stl

FVM-Tumbler-Plug_R2.stl

FVM-Tumbler-Rings.stl

FVM-Tumbler.stl

FVM_Base_Bottom_R2.stl

FVM-Hopper-Lid-Bezel.stl

Hopper-Screen_honeycomb.stl

Elon Musk is a true pioneer of this era. He broke the existing framework and it has gained the support of many people. This is a fresh shock to many who firmly believe in the existing order. He accelerated the popularization of electric vehicles, spread progressive designs to the public through cyber trucks, and finally began a full-fledged private space project.

Celebrating the launch of his successful spacecraft this time, I designed a dragon capsule and trunk.

This design is not foldable, but the capsules and trunk are fully structured and functional. The details were also made as much as possible. Its features are:

The hatch can be opened and closed.
The trunk can be connected.
You can connect by moving the umbilical connection.
Here's how to assemble this SpaceX Dragon capsule and trunk.

Insert the inner part of the capsule into the outer part. At this point, pay attention to the direction of the hatch.
Install the hatch. At this time, pay attention to the direction.
The trunk, first rotates the umbilical connection outward.
Rotate the bottom part.
Combine the holes in the bottom of the capsule with the projections on the trunk according to the direction.
Rotate and connect the umbilical connection.
Capsule and trunk are detachable.
Printing on Prusa and building process - https://youtu.be/Ome9Kdt-b6Y
Ender3 pro - https://youtu.be/3rhw3X0zM8E
CR10s pro - https://youtu.be/SkA7i96_dOM
Bluer - https://youtu.be/wgxMnjPXPHU

This design is designed to be mounted on a Falcon9 rocket that I designed. Here is the link to download the Falcon9 rocket.
https://cults3d.com/en/3d-model/game/space-x-falcon-9-rocket

I look forward to an era where space travel is possible as soon as possible.

Scale 1 : 66

Size, when all parts are fitted X 76mm, Y 76mm, Z 123mm

SpaceX Crew Dragon & Trunk

GOODesign_Capsule_Inner.stl

**🏷️ SPECIAL OFFER 🏷️ Use the code SAVE25 and get a 25% discount on my [membership plan](https://than.gs/u/1558026?plans=true) for 2 months!**

This is keychain shaped like a yarn ball with a built-in screw thread. It opens to store small items.

**No supports**

**Package includes:**
- Yarn ball with keychain loop
- Yarn ball without keychain loop

By putting some rustling pieces inside, you can also use it as a cat toy 😸

Follow us here on [Thangs](https://thangs.com/designer/KrakDrag) and on [Instagram](https://www.instagram.com/krakdrag3d/) to stay updated on upcoming designs!

This is a FREE model, but only my supporters are legally allowed to sell prints of my designs.

Happy printing and share your yarn ball! 

**3D printing settings:**
- Print model in provided orientation
- No Supports
- 0.12[mm] layer height
- 2 walls
- 20[%] infill
- For better bed adhesion you can use outer brim, but it's not necessary

Yarn Ball: Container keychain 

Yarn_keychain_nut_krakdrag.stl

CAPSULE

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

RMRRF Creator Capsule.

M3D - Fantastic Vending Machine

SpaceX Crew Dragon & Trunk