**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints**  

**Check out a spookier pendant light here
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980**

The Flustra (Fluss-truh) Pendant Light brings a modern vibe with a subtle twist

The clean, ribbed design complements a wide range of aesthetics, while the ripples underneath evoke a more dynamic sense of motion.


**Model Details:**
You can start printing this model right away on a Bambu printer using the prepared 3mf file optimized for printing this model.

This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**Other Home Decor:**
**The Hestra - Pendant Light, Vase Mode: https://than.gs/m/1042357
The Trysta - Pendant Light, Vase Mode: https://than.gs/m/1042457
The Stria - Pendant Light, Vase Mode:   https://than.gs/m/1042321
The Scura - Pendant Light, Vase Mode: https://than.gs/m/1046091**



**Safety First**
Intended for use with **9 watt LED Lights**  
Other lights can get too hot and damage/deform the plastic

**Print Settings:**
Vase Mode/Spiralize/Spiral Vase Mode
0.55 mm wall thickness
8 bottom shell layers
Print with the circular cut-out on the build plate

**100% Scale**
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


The Flustra - Vase Mode Pendant Light (Large), STL & Bambu 3MF

The Flustra - Vase Mode Pendant Light (Large)_Bambu by Mimetics3D.3mf

**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints**  

 
**Check out the latest 3 table lamps here:
Stria Table Lamp: https://than.gs/m/1049903
Trysta Table Lamp: https://than.gs/m/1049896
Hestra  Table Lamp: https://than.gs/m/1049906**


_Twisting waves of passion move beneath your calm, organized exterior.  The Hestra is for you_
 
The Hestra (Hess-truh) Table Lamp brings a modern vibe with a subtle twist

The clean, ribbed design complements a wide range of aesthetics, while the six underlying waves evoke a more dynamic sense of motion.

_Why hide who you are?  Let your passion shine through_



**Model Details:**
You can start printing this model right away on a Bambu printer using the prepared 3mf file optimized for printing this model.

This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**For some fun pendant lights, check out:
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980
The Flustra - Vase Mode Pendant Light (Large): https://than.gs/m/1047316**


**Safety First**
Intended for use with **9 watt LED Lights**  
Other lights can get too hot and damage/deform the plastic

**Print Settings:**
The lamp shad prints in Vase Mode/Spiralize/Spiral Vase Mode
The Base and cap print regularly without supports.  
**The base should be printed upside down**
0.55 mm wall thickness
8 bottom shell layers
Print with the circular cut-out on the build plate

**100% Scale**
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


Hestra Table Lamp - Vase Mode STL and Bambu 3MF

The Hestra - Vase Mode Pendant Light Bambu by Mimetics3D.3mf

**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints**  
 
**Check out the latest 3 table lamps here:
Stria Table Lamp: https://than.gs/m/1049903
Trysta Table Lamp: https://than.gs/m/1049896
Hestra  Table Lamp: https://than.gs/m/1049906**

_You cut a striking figure where the light and shadow meet.  To observe from just one angle leaves the picture incomplete_  

_The Trysta is for you_

The Trysta (Tris-tuh) Table Lamp graces each room with modern elegance.
 
The clean, ribbed design complements a wide range of aesthetics, while the vertical pattern both hides and accentuates the curves that lie within.

_What's holding you back?  Rendezvous with destiny_

**Model Details:**
You can start printing this model right away on a Bambu printer using the prepared 3mf files optimized for printing this model.

This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**For some fun pendant lights, check out:
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980
The Flustra - Vase Mode Pendant Light (Large): https://than.gs/m/1047316**

**Safety First**
Intended for use with **9 watt LED Lights**  
Other lights can get too hot and damage/deform the plastic

**Print Settings:**
Vase Mode/Spiralize/Spiral Vase Mode for the Lamp Shade
Regular printing for the Base and Cap
0.55 mm wall thickness
8 bottom shell layers
Print with the circular cut-out on the build plate

**100% Scale**
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


Trysta Table Lamp - STL and Bambu 3MF

The Trysta - Vase Mode Pendant Light_Bambu by Mimetics3D.3mf

**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints** 

**Check out a spookier pendant light here
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980**

_The sides of you others can't see convey a hint of mystery.  The Scura calls to you_
 
The Scura (Skyur-Uh) Pendant Light brings a modern vibe with a subtle twist

The clean design complements a wide range of aesthetics, while the broad, curved fins add a more dynamic sense of depth to the room.



**Model Details:**
You can start printing this model right away on a Bambu printer using the prepared 3mf file optimized for printing this model.

This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

The Scura represents the fourth design in the Mimetics3D Home Decor collection.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**Other Home Decor:**
**The Hestra - Pendant Light, Vase Mode: https://than.gs/m/1042357
The Trysta - Pendant Light, Vase Mode: https://than.gs/m/1042457
The Stria - Pendant Light, Vase Mode:   https://than.gs/m/1042321**

**Safety First**
Intended for use with **9 watt LED Lights**  
Other lights can get too hot and damage/deform the plastic

**Print Settings:**
Vase Mode/Spiralize/Spiral Vase Mode
0.55 mm wall thickness
8 bottom shell layers
Print with the circular cut-out on the build plate

**100% Scale**
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


The Scura - Pendant Light, Vase Mode Bambu 3MF

The Scura - Vase Mode Pendant Light_Bambu by Mimetics3D.3mf

**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints** 

For a bowl version, check out:
**Faces Of Death Bowl - Skull Bowl - https://than.gs/m/1046122**

For another fun pendant light:
**The Flustra - Vase Mode Pendant Light (Large): https://than.gs/m/1047316**

 
The Faces of Death Pendant Light brings a touch of the macabre to any room



**Model Details:**
You can start printing this model right away on a Bambu printer using the prepared 3mf file optimized for printing this model.

This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**Other Home Decor:**
**The Hestra - Pendant Light, Vase Mode: https://than.gs/m/1042357
The Trysta - Pendant Light, Vase Mode: https://than.gs/m/1042457
The Stria - Pendant Light, Vase Mode:   https://than.gs/m/1042321
The Scura - Pendant Light, Vase Mode: https://than.gs/m/1046091**

**Safety First**
Intended for use with **9 watt LED Lights**  
Other lights can get too hot and damage/deform the plastic

**Print Settings:**
Vase Mode/Spiralize/Spiral Vase Mode
0.55 mm wall thickness
8 bottom shell layers
Print with the circular cut-out on the build plate

**100% Scale**
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


Faces of Death - Vase Mode Pendant Light, Bambu 3MF

Faces of Death - Vase Mode Pendant Light_Bambu by Mimetics3D.3mf

**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints**  

**Check out a spookier pendant light here
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980**

_You cut a striking figure where the light and shadow meet.  To observe from just one angle leaves the picture incomplete_  

_The Trysta is for you_

The Trysta (Tris-tuh) Pendant Light graces each room with modern elegance.
 
The clean, ribbed design complements a wide range of aesthetics, while the vertical pattern both hides and accentuates the curves that lie within.

_What's holding you back?  Rendezvous with destiny_

**Model Details:**
You can start printing this model right away on a Bambu printer using the prepared 3mf file optimized for printing this model.

This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

The Trysta represents the third design in the Mimetics3D Home Decor collection.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**Other Home Decor:**
**The Hestra - Pendant Light, Vase Mode: https://than.gs/m/1042357
The Trysta - Pendant Light, Vase Mode: https://than.gs/m/1042457
The Stria - Pendant Light, Vase Mode:   https://than.gs/m/1042321
The Scura - Pendant Light, Vase Mode: https://than.gs/m/1046091**

**Safety First**
Intended for use with **9 watt LED Lights**  
Other lights can get too hot and damage/deform the plastic

**Print Settings:**
Vase Mode/Spiralize/Spiral Vase Mode
0.55 mm wall thickness
8 bottom shell layers
Print with the circular cut-out on the build plate

**100% Scale**
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


The Trysta - Vase Mode Pendant Light with Bambu 3MF

The Trysta - Vase Mode Pendant Light_Bambu by Mimetics3D.stl

Bring the Cincinnati skyline into your home in true 3D! These make for the perfect gift or home decor for residents, travelers, and admirers of the city.

**This listing includes three different sizes - Small, Medium, and Large - with a solid base and with the water trimmed away.**

_Subscribe to keep an eye on the **new models we release each week**!_

**Steps**:
1. Import the STL to your slicer. 
2. Scale the X or Y dimension to the desired size with 'Uniform scale' checked.
3. Print as one-piece or split into tiles in the slicer for larger sizes.
5. Slice and print!
6. Set on shelf, tabletop, or hang on wall with sticky mounting strips. 
7. Optionally, stylize it with a frame and background mat or multi-color print in your unique way!

**About the models**
These are the most detailed and accurate 3D-printable cityscape and landscape models available. Each is designed and optimized from Micropolitan's 5+ years of experience developing and selling 3D prints of iconic locations worldwide. Each model is designed by hand, using a combination of data and reference imagery. We use LiDAR and refine the architecture, block by block, using digital sculpting tools and satellite imagery. The models are then optimized for detail preservation while keeping the file size manageable for everyday computers.

**Making your piece**
These make perfect centerpieces or collections for your home, to document your travels, or as distinct and unique gifts. Many design options are available - framed and unframed, for wall, tabletop or shelf display. They can be printed in a range of sizes with stunning detail, typically from 6"x6" up to 12"x12"+. The model can be cut into 4+ tiles to print and assemble a piece larger than your build plate. 

- Size: Scale to at least 150x150mm to preserve details.
- Layer height: 0.18-0.25mm
- Nozzle: 0.4-0.6mm
- Infill: 15% Gyroid
- Walls: Arache OFF (use classic)

**Styling and display**
These look great framed or unframed! They can be displayed on tabletops, shelves, or hung on the wall with mounting strips. They look best when lit from the side. Display near a window, lamp or downlight to make the 3D features pop.

**Materials**
Filament: For a minimalist look and best grayscale shadowing, use a matte white PLA. Marble and silky filaments are also popular looks.
Frames: Choose a frame or shadow box that fits your print dimensions. 

This 3D model was developed with reference data sources and satellite imagery from OpenStreetMap © OpenStreetMap contributors and USGS 3DEP.

Cincinnati, OH - S, M, & L

Cincinnati, OH_L_Water.stl

**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints**  

**Check out the latest 3 table lamps here:
Stria Table Lamp: https://than.gs/m/1049903
Trysta Table Lamp: https://than.gs/m/1049896
Hestra  Table Lamp: https://than.gs/m/1049906**

The Stria (Stry-uh) Table Lamp adds a touch of modern elegance to any room.
 
The clean, ribbed design complements a wide range of aesthetics.

You can start printing this model right away on a Bambu printer using the prepared 3mf file optimized for printing this model.
 
This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**For some fun pendant lights, check out:
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980
The Flustra - Vase Mode Pendant Light (Large): https://than.gs/m/1047316**

For some spookier decor check out:
**Faces Of Death Bowl - Skull Bowl - https://than.gs/m/1046122**

**Safety First**
Intended for use with **9 watt LED Lights**.  Other lights can get too hot and damage/deform the plastic

**Print Settings:**
Vase Mode/Spiralize/Spiral Vase Mode
Base and Cap print in regular mode
0.55 mm wall thickness
8 bottom shell layers. 

100% Scale
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


Stria Table Lamp - STL and Bambu 3MF

Stria_PendantLamp_VaseMode_Bambu.3mf

**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints**  

**Check out a spookier pendant light here
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980**

_Twisting waves of passion move beneath your calm, organized exterior.  The Hestra is for you_
 
The Hestra (Hess-truh) Pendant Light brings a modern vibe with a subtle twist

The clean, ribbed design complements a wide range of aesthetics, while the six underlying waves evoke a more dynamic sense of motion.

_Why hide who you are?  Let your passion shine through_

**Model Details:**
You can start printing this model right away on a Bambu printer using the prepared 3mf file optimized for printing this model.

This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

The Hestra represents the second design in the Mimetics3D Home Decor collection.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**Other Home Decor:**
**The Hestra - Pendant Light, Vase Mode: https://than.gs/m/1042357
The Trysta - Pendant Light, Vase Mode: https://than.gs/m/1042457
The Stria - Pendant Light, Vase Mode:   https://than.gs/m/1042321
The Scura - Pendant Light, Vase Mode: https://than.gs/m/1046091**



**Safety First**
Intended for use with **9 watt LED Lights**  
Other lights can get too hot and damage/deform the plastic

**Print Settings:**
Vase Mode/Spiralize/Spiral Vase Mode
0.55 mm wall thickness
8 bottom shell layers
Print with the circular cut-out on the build plate

**100% Scale**
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


ARCHITECTURE

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

The Flustra - Vase Mode Pendant Light (Large), STL & Bambu 3MF

Hestra Table Lamp - Vase Mode STL and Bambu 3MF

Cincinnati, OH - S, M, & L