Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4923358.

Rainbow in pride colors. Print each stl in different colour, glue together if needed but it holds together well if just sitting on a desk. Pictures above were printed in 0.3 layer height.

Pride Rainbow

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4929315.

SUBWAY SUPREME logo paperweight for hypebeasts to waste their filament on!

Comes in two sizes, 15mm and 30mm thickness. Print out each separately in their respective colour and fit together.

Print pictured is 0.3mm layer height.

If you like my designs and would like to see more please consider donating/tipping.

SUBWAY SUPREME logo paperweight

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5023557.

Cool pattern that produces an optical illusion when viewed at different angles. Comes in single tile, 2x2 and 3x3 sizes. A colour change is required this can be done easily in prusaslicer or cura.

Pattern created using https://www.svgbackgrounds.com

If you like my designs and would like to see more please consider donating/tipping.



Optical illusion tile (OP ART)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4989778.

Champion logo plate that can be customised by printing with different inserts and colours.

If you like my designs and would like to see more please consider donating/tipping.

Champion custom logo sign plate

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4912595.

Miniature Giants Causeway desk model. Print the base in green for grass or blue for sea.


Recommended slicer settings

Base:
- In your slicer rotate it to print upright on the long side nearest to rocks, see picture. This will give you the detailed shimmer effect seen in pictures.
- 0.2mm layer height
- Select brim in your slicer, I used a brim width of 5. This helps support the print and is easily removed after.

Rocks:
- 0.2mm layer height
- Enable ironing in your slicer to make the rocks smooth on top.

Filment used:
eSun green PLA +
eSun blue PLA +
Matt grey PLA

Printer:
Prusa i3 MK3S

Any questions leave me a comment!

Giants Causeway Miniature Desk Model

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5020303.

Cross from the A Cross the Universe album by Justice. Print each part separate and fit together.

If you like my designs and would like to see more please consider donating/tipping.

A Cross the Universe (Justice album)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4972884.

Logo plaque from the movie PSYCHO for your desk or wall.

I printed with a filament colour change. This can be done easily in prusaslicer and cura.

Printed successfully at 70% and above scale :)


If you like my designs and would like to see more please consider donating/tipping.



PSYCHO movie logo wall plaque art

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4915510.

Simple 'White Bear' model from black mirror. Easy and fast to print!

Recommended slicer settings:

0.2mm layer height
enable 'ironing' to get smooth front/top surface
Print in white obvs :P



Black Mirror 'White Bear' model

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4935927.

Simple minimalist modern planter for your plants or succulents. Comes in two sizes 70mm and 100mm. 

It is made with three parts that can then be glued together. Print the insert part out in your preferred color.

Print pictured is printed at 0.3 layer height with purple insert.

If you like my designs and would like to see more please consider donating/tipping.

Modern ring planter

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4949349.

A fully functional 90s coca-cola yoyo replica. Requires a M3x20mm bolt and a hex nut. 

The 2 bases (white coloured parts) require VERY minimal support to print the inside. 

Assembly instructions:
1. Use the "screw pulling technique" to fix the hex nut in place. Take one side of the base (labelled A in picture) and place the hex nut over the hole on the outside. On other side screw in bolt and tighten until it pulls the hex nut into the hole. Remove bolt.
2. Assemble the bearing. Fit both pieces B and C together until edges flush. Should be a 2.5mm gap for the string.
3. Put everything together like pictured. M3x20mm into base (D) without nut, through the bearing (B+C), and into the base with embedded nut (A). Tighten with allen/hex key. Fit outside coloured panels (E and F)

If you like my designs and would like to see more please consider donating/tipping.

90s Coca-Cola yoyo replica

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4928507.

Asteroid plant pot for your flowers or succulents. Comes in two sizes 70mm and 100mm.

No special settings needed for printing, the prints in the pictures are 0.3mm layer height.

If you like my designs and would like to see more please consider donating/tipping.

Asteroid plant pot

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4936669.

Oasis logo plaque / 2D wall art. Part of an Album Art Project I'm doing. A lot more bands and albums to come. Requests Welcome!

Print stl labeled black in black
Print stl labeled white in white
Insert white pieces into black base. Should fit snuggly, no glue needed.

I've printed at 100% and 75% scale and works great!

If you like my designs and would like to see more please consider donating/tipping.

Oasis logo plaque 2D Wall Art - Album Art Project #1

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4928096.

A trippy Himalayan salt lamp. To achieve the effect you see in the picture you need to use the following settings in your slicer with white filament:

- 0.2mm layer height
- 2 perimeters (if the 0.2mm layer height hasn't set it already).
- 2% infill (yes 2%! it will print fine :D)
- gyroid infill type

Then simply get a cheap push button or wireless LED light and stick it to the bottom. Sometimes they are known as round cabinet or closet LED lights. The combination of 2 perimeters and 2% gyroid infill will give a cool effect!

Trippy Himalayan Salt Lamp

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4909673.

Simple 2D wall art of Bender from Futurama.

Tested with the default Prusa slicer 0.2mm (quality) profile with 0.2mm layer height and works great.
"avoid crossing perimeters" recommended if you have stringing

Leave a comment if you'd like to see more characters!

Bender 2D Wall Art Futurama

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4960769.

typing...

Apple iMessage bubble

typing... Apple iMessage bubble

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4941703.

Pen pot / pen holder for your desk or home office. Measures 80mm x 80mm x 100mm but can scale down easily.

Print pictured is printed at 0.3 layer height.

If you like my designs and would like to see more please consider donating/tipping.

Smile pen pot (pen holder)

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

wafflecart

Achievements

Seedling

Debutant