Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2036653.

This mount was made for the QAV and QAV clone frames. But it is super easy to modify and adjust to fit just about any flat top frame. I wanted something better than cheap looking foam, but just as light, something that can hold up in a crash but give a little in small bumps. Coming in only at 2.8 grams, this is on par with a piece of lose wobbly, hard to level your cam, crap foam. I also added just enough of a cavity under the print to add double sided sticky tape or a bead of hot glue to get this to stick down. Now just drop your cam on and strap it in for a ripping of a life time. This thing works like a dream if you print at my recommended settings. I highly recommend TPU for this. It's a must, and super cheap on amazon, well worth the money.

Minimal Ultra Light GoPro Mount 1.0

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1719752.

This is a complete redesign of the lower portion of the motor mount that can be used with the FireFly drone. http://www.thingiverse.com/make:235170
The original design looked nice but was hard to print and very weak as a 3d Print. This is to be printed on its flat back side. The Simplify3D photo shows the orientation that prints best. I'm currently working on a design for the top portion of the of the motor mount that can be printed just as easy.

FireFly Strengthened Bottom Motor Mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2865952.

This is a Nerf blaster stock that has a battery compartment to house larger lipos. I used m3 screws to lock this in place. I'm working on a version with the traditional nerf mechanism but it prints out pretty weak, so I'm figuring that out. This was originally designed for my Demolisher, but fits all of my Nerf blasters really well, including my Stryfes and springers like the Retaliator. I've also added a deeper well to the Butt portion of the stock to house much larger Lipos. I was able to fit a 2200 3s lipo using the Butt Deep option. 

This was modeled from scratch by me, but I did take some style direction for part of this from fantasticmrdavid's Nerf Demolisher battery stock, so its not a remix, but here is the link to that. thingiverse.com/thing:2526152

Nerf Battery Stock Demolisher and Stryfe

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2349470.

This is a small Skid for the tattu 3s 450 mAh lipo. Ive seen a few designs like this, where you can tilt it forward for a quick take off at the races. I've made the geomotry very basic so anyone can edit to change the angle when it tilts forward. This come stock with about a 25 degree tilt to match my camera angle. I printed this at a 20% infill, with 3 walls and 5 bottom layers and 5 top layers. It comes in only at 3g.

450 mAh Tattu Micro Lipo Protector

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2869232.

TWO!! Yes, you have two options for a Demolisher Picatinny Top Rail. I've made a simple skinny rail and a wide base rail that fills out, what I felt like was and odd tall gap. The wide model flows well into the body of the Demolisher. For both you will need to cut out the first stop on the nerf rail. This way you get a solid connection. I just used flush side cutters. 

Demolisher Nerf Picatinny Top Rail Wide And Skinny

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1719942.

FrSky X8R Receiver & Antenna Mount - I made this originally to be used with the FireFly http://www.thingiverse.com/make:235170 printable drone. I couldn't find anything that suited my needs in mounting and protecting my receiver. Just print the parts in the orientation shown in the Simplify3D image with support material, and then glue the mount parts together, zip-tie, and your ready to rock! 

FrSky X8R Receiver & Antenna Mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:309133.

<h3>UPDATE 1/22/2020</h3>
<blockquote>This has been updated so you can just print at 100%, and should require no adjustments. I've also included a even shorter version for those who were having an issue with hitting a base plate. The longer version is nice for those that have lager hands and a mag with out an over sized base plate. </blockquote>

This allows you to draw back the magazine follower with one had and load with the other with out killing your thumb. This works on quite a few 22LR magazines. This is the half size version of a [thumb saver for a 22lr High Standard with a military style grip](http://www.thingiverse.com/thing:309058). 

- High Standard Supermatic Citation  
- High Standard Supermatic Trophy  
- High Standard Olympic  
- High Standard Victor  
- High Standard Target  
- High Standard Rec  
- Ruger Mark I  
- Ruger Mark II  
- Ruger Mark III 
- 22/45
- 22/45 Lite
- Smith and Wesson SW22 Victory

Let me know if you have more to add to the list. 

Thumb Saver For 22lr Pistol Magazines

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2867166.

This is a replacement Picatinny Side Rail the Demolisher. to install you need to remove the screws from inside the blaster. To attach I used 10mm m3 screws.

Demolisher Nerf Picatinny Side Rail

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:309058.

Thumb saver for a 22lr High Standard with a military style grip. This is full length and locks in place so you can load all 10 rounds with ease. This thumb saver may work on other High Standard 22lr mags, but it might not hold the slide all the way open.  

I have another that is a [half length thumb saver](http://www.thingiverse.com/thing:309133) that uses less plastic and is more of a universal design for 22lr pistol mags, but you will have to hold onto it the whole time. I just like having the options.

High Standard Thumb Saver

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1792796.

This mount is for a the QAV 250 & 180 Models. This may fit other QAV models. This was designed to dampen any small vibrations from your quad and also any impact from a crash.

QAV Go Pro Mount 20°

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2350853.

This is a small Skid for the tattu 3s 650 mAh lipo. Ive seen a few designs like this, where you can tilt it forward for a quick take off at the races. I've made the geometry very basic so anyone can edit to change the angle when it tilts forward. This come stock with about a 25 degree tilt to match my camera angle. I printed this at a 20% infill, with 3 walls and 5 bottom layers and 5 top layers. It comes in only at 3.5g.

650 mAh Tattu Micro Lipo Protector

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

vwclogan

Achievements

Seedling