Use your unused Altoids cases to store your nozzles! Up to 6 Revo nozzles.

Altoids Nozzle Organizer - Revo

Altoids Nozzle Organizer ×6 for Revo nozzles v1.step

Altoids Nozzle Organizer ×6 for Revo nozzles v4.step

Use your unused Altoids cases to store your nozzles! Up to 24 V6 nozzles.

Altoids Nozzle Organizer - V6 nozzles

Altoids Nozzle Organizer ×24 for V6 nozzles v2.step

Use your unused Altoids cases to store your nozzles! Up to 24 Mk8 nozzles.

Altoids Nozzle Organizer - Mk8 nozzles

Altoids Nozzle Organizer ×24 for MK8 nozzles v8.step

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3968151.

This is a remix of part of [this design](https://www.thingiverse.com/thing:3564068). The original A_B frame is meant to be screwed on an aluminum extrusion frame or an enclosure, making it unstable for stand-alone usage. It's also pretty difficult to print on filaments that aren't PLA (I struggled to print an usable version on PETG).

This is the 5th iteration of the stand-alone A_B frame I designed myself, it allows the usage of the original holders on a tabletop or inside a dry box. I strongly recommend using it with the bearing version of the spool shaft from the original thing, the spools rolls smoothly and without resistance.

Stand alone ball bearing spool holder 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4405896.

Made just to make a point on reddit: https://www.reddit.com/r/3Dprinting/comments/gsfs6v/i_will_3d_model_any_race_track_for_you/

Downloaded the SVG file from [Wikipedia](https://en.wikipedia.org/wiki/Aut%C3%B3dromo_Jos%C3%A9_Carlos_Pace#/media/File:Circuit_Interlagos.svg), cleaned the file up using Inkscape and finalized the 3D model on Fusion 360. Took me less than 10 minutes. Pitlane not included, just like the reference on the link above.

Autódromo José Carlos Pace (Interlagos), 1977 version

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3899731.

This is a remix of a remix. The original file uses GX16 connectors for general wiring, and XT60 for power. The remix uses a DB37 connector (?) for general wiring, and a Auto 6 Pin Power (??) connector for power.

This backplate remix uses GX12, GX16, and GX20 connectors, all chosen carefully to avoid mistakes. Also added text identification in sunk relief near them.

* 4× 4 pins GX12 connectors for each stepper motor (X, Y, Z, and extruder)
* 1× 6 pins GX12 connector for the endstops (X, Y, Z)
* 1× 4 pinx GX16 connector for the fans (overkill, but chosen to avoid confusion with the stepper motors connectors)
* 1× 4 pins GX20 connector for the bed and hotend heaters (the pins of this connector are rated for 10A, a typical 40W heater cartridge on a 24V system like the Ender 5 will draw 1.67A max, so that's overkill for safety reasons) ***EDIT (2019-10-07):** But the standard 24V bed heater for Ender-3/5 has 220W of maximum power, which gives us ≈ 9.2A of current. Too close the maximum specs of the chosen GX20 connector. The thing has been marked as a WIP and will be altered later to include a XT60 connector for the heater bed and another GX12 for the hotend cartridge heater. Better be safe than sorry.*

All those connectors were sourced from Aliexpress: https://www.aliexpress.com/item/32820896230.html Be careful when wiring the connectors! I didn't add a wiring guide because each system is different, use your common sense when doing that, and check often!

I also added the standard LCD plate for the Ender 3; the LCD plate of the Ender 5 is different, it has a tab that doesn't exist on the Ender 3.

WARNING: I'm releasing the Backplate file some hours after finishing the design, so it is still untested. The LCD plate is tested and should fit.

***UPDATE (2020-10-26):*** finally finished the addition of the XT60 connector holder for the backplate. Also added a mounting clamp to allow bolting the connector. Both come from this case: https://www.thingiverse.com/thing:3631413

 Ender 3 External Electronics Case with GX12/GX16/XT60 connectors

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3703528.

A design exercise to allow replacing the [standard Ender 3 LCD support](https://github.com/Creality3DPrinting/Ender-3/blob/master/Ender-3%20Mechanical/PDF/LCD%20support.pdf) for a PanelDue (5i or 7i, your choice).

Untested, I've made these designs using 3D models as reference. STEP files included for further modifications if needed.

July 1st, 2019: added the version for the 4.3" PanelDue as requested.

Ender 3 LCD supports for PanelDue 5i & 7i

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3703243.

Quick design exercise, adapting the right case for use with a Duet 2 Wifi.

Not tested, and because of that I'm also adding the STEP file, so you can make modifications if needed. Will probably need tree supports for the front cutout.

Ender 3 Right Case for Duet 2 Wifi

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

vinnycordeiro

Achievements

Seedling

Debutant