Cap for 2" Net Pot

Print Settings
Printer:
Ender 3
Supports:
No
Resolution:
0.2mm
Infill:
20%
Filament material:
PLA

https://www.buymeacoffee.com/vermontsfinest

2in net pot cap

2in_net_pot_cap.stl

Ceiling mount for the OPTOMA UHD50 Projector.

Projector bolt positions are taken from the mounting section of the owner's manual and line up perfectly on mine.

I printed the top and bottom pieces out of PLA at 50% infill, the gimble piece in the center was printed in PETG at 50% infill. The spacers/washers were out of TPU and at 100% infill.

The holes connecting the three pieces are for 1/2" bolts, the ones for the projector are for M4 screws and the ones for the ceiling are 0.2" because that's the size wood-screw I had on hand.

My projector is 15 lbs, and I was able to hold 30 lbs without noticeable deformation however keep in mind your experience may vary depending on layer adhesion, temperature, and other unforeseen factors. I have a safety cable bolted to a stud in my ceiling as a safety precaution.

Hardware list:
Projector hardware:
Qty. 3: M4 x 0.7 mm Thread, 16 mm Long Socket Head Cap Screw (McMaster part # 91290A154)

Mount hardware:
Qty. 2: 1/2"-13 Thread Size, 2-1/4" Long, Partially Threaded (McMaster part # 92198A721)
Qty. 2: Grade 5, 1/2"-13 Thread Size Hex Nut (McMaster part # 95505A605)

Ceiling hardware:
Qty. 3: Zinc-Plated Steel, Number 10 Size, 1" Long Flat Head Wood Screw (McMaster part # 90006A247)


Print Settings
Printer:
Ender 3
Supports:
Yes
Resolution:
0.16
Infill:
50-100
Filament material:
PLA, PETG, TPU


https://www.buymeacoffee.com/vermontsfinest

OPTOMA UHD50 Projector Ceiling Mount

Projector_Mount.stl

Simple window blind twist rod for blinds with a hook.

Print Settings
Printer:
Ender 3
Supports:
Yes
Resolution:
0.2mm
Infill:
20%
Filament material:
PLA

https://www.buymeacoffee.com/vermontsfinest

Window Rod

Simple window blind twist rod for blinds with a hook

A simple slide-in wall mount with clip for an Amazon Fire 10 HD with wire passthrough behind the device for a clean look. 

Print Settings
Printer:
Ender 3
Supports:
Yes
Resolution:
0.2mm
Infill:
20%
Filament material:
PLA

Charging wire used:
https://www.amazon.com/dp/B08Z3D93SD?psc=1&ref=ppx_yo2ov_dt_b_product_details

https://www.buymeacoffee.com/vermontsfinest

Fire 10 HD Wall Mount

Simple clip-in wall mount for an Amazon Fire 10 HD with wire passthrough behind the device for a clean look. 

Print Settings
Printer:
Ender 3
Rafts:
No
Supports:
Yes
Resolution:
0.2mm
Infill:
20%
Filament material:
PLA


Charging wire used: [https://www.amazon.com/dp/B08Z3D93SD?psc=1&ref=ppx_yo2ov_dt_b_product_details](url)

I engineer, design, print, and test general use and quality of life designs. I have 6 years of experience using SolidWorks and 3 years of using Onshape (a free-to-use online 3D modeling program. My main printer is a heavily modified Creality Ender 3, secondary printer is a GEEETECH A30

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

vermontsfinest

Achievements

Seedling

2in net pot cap

OPTOMA UHD50 Projector Ceiling Mount

Window Rod

Fire 10 HD Wall Mount