Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5427215.

This is a relatively quick one - it's a basic frame that fits the Teenage Engineering TX-6 Mixer next to a very similiarly sized Ikea Frekvens mini bluetooth/Aux speaker. 
You obviously need a cable to get audio from one to the other.


It's not really for portability - the Frekvens speaker doesnt actually lock in, it just fits into the side of the frame with a small knob that fits into the hole where the speaker metal stand would go. This is just for keeping things vaguely organised on a desk.
The TX-6 fits snug wwith a little thing that slides on once it is in place - the frame also hides the switch away between the speaker and mixer.


Teenage Engineering TX-6 + Ikea Frekvens Frame

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4960138.

Modified buttons for the PiBoy DMG by Experimental Pi.

It is a combination of the lever design of one and the side fixture of another which is like the normal PiBoy buttons. Should be compatible with the normal PiBoy Shell but I used a modified 3D printed one with more ventilation as well:
https://www.thingiverse.com/thing:4947746
The original bumper design with it's own bracket to screw into the backshell didn't work with the replacement printed shell - the middle part needed modification and once I got it to fit, it was too loose and required fixation with glue which did not hold well for me. These don't need the bracket but don't have quite as good actuation of the buttons, needs to be pressed on a slightly less range of angles. If you can work this out, remix it and tell me so I can use yours. 

Huuuuuuuge thanks to the people that released these STLs especially the shell, holy moly on thingiverse for free for those of us who do not want to pay for prints. (No hate to those selling them either, you do you)

Modified PiBoy DMG Bumper Buttons

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4928453.

I printed this case for my Miuzei touch screen mounted on my raspberry pi 4. https://www.amazon.com/Miuzei-Raspberry-Full-Angle-Heatsinks-Raspbian/dp/B07XBVF1C9

https://www.thingiverse.com/thing:4663911

But I wanted a way to mount it to the Prusa non-permenantly and in an aesthetically pleasing manner. I designed this caddy thing to hook onto the aluminium extrusion and hold it at a nice angle for touch screen usage.

I ended up printed the lower half of the case with just infill and no top and bottom layers to give it some air flow underneath the Pi, but I did that in PrusaSlicer and don't have an STL or 3mf file for that one.

I printed it with supports but with minimal infill as it's not really high load bearing. I made it so the hooks hook in at a height were the base of the model sits on the same surface as the printer with the default rubber feet.


Miuzei Raspberry Pi 4 Touch Screen Holder for Prusa i3

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4930074.

My wife was the fortunate recipient of this Diptyque car diffuser as a gift. It smells very nice and has a very nice design and is very expensive for what it is. Unfortunately it is designed to fit on a vent flap that doesn't exist on the front of her Tesla Model 3. I used the spacer insert from the previous remixed phone holder design and quickly added a prong for the diffuser to hug onto. I made the spacer a little bit shorter as when I printed it to prototype, it raised the dashboard on top a bit too much for my liking.

Don't buy this car diffuser because even though it smells nice and looks cool, it's ridiculously expensive. But if you happen to own one, and a Model 3. This is for you.

Probably better in PETG but I printed it in PLA because it's still winter here.

Diptyque Car Diffuser Mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5380048.

My mother-in-law is an avid golfer and wanted something that would hold up a small bag with shoes or a change of clothing on the inside of her electric golf buggy.
This prints in two parts without supports but may require some glue to join the two pieces together.
I printed in PETG given it would be outside and in the sun while having weight on it at the end.

PowKaddy CT6 Buggy Bag Hook

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4517998.

This object was made in Tinkercad. Edit it online https://www.tinkercad.com/things/arXG77gcsab

Stand for Miuzei Raspberry Pi 4 Touch Screen angled

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4577132.

For anyone who has a PowerA Moga grip, and may want to play games in portrait orientation with a controller e.g. Nintendo DS emulation on Delta emulator. 

I did a quick job for it, so it just slides onto the preexisting Moga clip. It has no moving parts.
It may be wide for a bare iPhoneX - I use it with case.

I print it with supports because my printer is terrible, so I'm not sure how it would go without.

PowerA MOGA Xbox Grip Portrait Adapter

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

urbanvanilla

Achievements

Sequoia

Voyager