This will fill the grip gap and stabilize a full-size magazine in a subcompact glock. Available with and without the finger groove. Be calibrated.

Glock 17 to 26 magazine sleeve

g17 to g26 sleeve.stl

This is a tray case for a keyboard you might receive as part of a "Mystery PCB" order from [clawboards.xyz](https://clawboards.xyz). Clawboard's minivan was an experimental break-apart keyboard with independent control for the main key cluster, the numpad and navigation clusters, and the f-key row. As you might imagine, it didn't take off, so now it's being sold at a greatly reduced price as part of a gimmicky way to get rid of the inventory.

You can buy a superior and similar keyboard, "the coupe," from the same source. However, that keyboard won't fit this case, because the controller and cable entry are located differently on that board. Because of this, the .3mf isn't going to be very useful, but you can have the .f3d as well, and maybe you can adapt this case to something more standard.

Minivan Keyboard Case

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4620560.

This is an air shroud for adapting a Supermicro SC826 chassis into providing adequate cooling for the CPU and memory in an HP Z420 motherboard. It was designed out of the fear that the ECC memory would not be receiving adequate airflow otherwise, but the system seems to do fine without the shroud.

I went through the trouble of verifying this shroud through temperature measurements, since using PLA in a thermal solution is a questionable decision that can lead to fires if the temperatures in question are too great. Where possible, I used software monitoring, but memory had to be measured with thermocouples. For load, I just used mprime (aka prime 95) to torture test the memory and CPU at near 100% utilization. These are the only components to be directly worried about due to the shroud, but I should mention that one of the memory ducts exhausts directly into the PCIe slots. If there's anything temperature sensitive there, it might need further attention.

For memory temperature, I was seeing DRAM package temperatures near 40 C on the memory closer to the fan wall, and near 50 C on the memory further from the fans. Considering that Micron specifies a "self reset" package temperature of 85 C, this is fairly temperate. It's also nowhere near damaging the air shroud.

As for CPU temperature, when using an active cooler (SM # SNK-P0048AP4) on a 165W TDP CPU (Xeon E5-1603), I was seeing core temperatures peaking near 60 C, which isn't going to hurt the air shroud either.

It's worth noting that I'm using the stock fans, which are rated near 75 CFM each. I tried using quieter fans as well, and got memory temperatures and CPU temperatures that were about the same. However, I didn't think the noise got below the threshold that would have made it worth the trouble, as the power supplies for these chassis are very loud.


CSE-826 Air Shroud

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5258955.

Right, so I needed a tap case. I was inspired by the compactness of [this design](https://www.thingiverse.com/thing:3504168), but I needed something that would just hold two copies of the five taps I basically design around for a living. Because when it comes to easily broken consumables, "one is none."

The fit with the lid is pretty tight. Consider slowing your print speed down far enough to avoid ringing artifacts and ghosting.

Here's the refill list:
1/4-20 spiral point plug tap ([mcmaster # 2523A411](https://www.mcmaster.com/2523A411/))
5/16-18 spiral point plug tap ([mcmaster # 2523A412](https://www.mcmaster.com/2523A412/))
3/8-16 spiral point plug tap ([mcmaster # 2523A413](https://www.mcmaster.com/2523A413/))
7/16-14 spiral point plug tap ([mcmaster # 2523A414](https://www.mcmaster.com/2523A414/))
1/2-13 spiral point plug tap ([mcmaster # 2523A415](https://www.mcmaster.com/2523A415/))

Coarse US Tap Case

UNC Tap Case

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4691627.

I wanted a 3D printed hanger for Nagmay's [pandemic globe ornament](https://www.thingiverse.com/thing:4670812). Print two halves, snap in at the top. Don't use support material, and if you've got anti-stringing measures figured out, use them.

Optimized for a 0.4mm nozzle.

Ornament Hanger

I mostly use my 3D printer to quickly make functional parts in support of my other activities. What I can share, I share.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

tmfacets

Achievements

Seedling

Debutant

Glock 17 to 26 magazine sleeve

Minivan Keyboard Case

CSE-826 Air Shroud

Coarse US Tap Case

Ornament Hanger