This is a remix of https://www.thingiverse.com/thing:2844013 which is itself based on several other models. 

The following is changed:
- Scaled the width of the models to 101%
- Deepened the indentations of the ports by 0.5mm
- Made the bottom 75% (approximately) of the case much thinner, saving material.
- Added feet to the bottom of the case so the bottom of the Pi is cooled better
- Added rails to the side of the case for mounting on an Ender 3 (v2) or printer that uses the same extrusion profiles
- Increased the connector hole sizes to ensure that cables always fit and alignment is not a problem

No bolts or nuts are needed for this case. The lid/cover is held in place by friction and the ports.

The rail on the side of the case is optional, but it's ideal for mounting it on a 2020/2040 aluminum extrusion v-slot profile. This includes the Ender 3 (v2).

The model with half a rail makes it possible to mount the case under the LCD panel.



Boltless Raspberry Pi 3B+ case (3, 2 & B+ also fit) - More Cooling, Less Material Used, Printer Mounting Rail

This is a remix of https://www.thingiverse.com/thing:2844013 which is itself based on several other models. 

The following is changed:
- Scaled the width of the models to 101%
- Deepened the indentations of the ports by 0.5mm
- Made the bottom 75% (approximately) of the case much thinner, saving material.
- Added feet to the bottom of the case so the bottom of the Pi is cooled better
- Added rails to the side of the case for mounting on an Ender 3 (v2) or printer that uses the same extrusion profiles
- Increased the connector hole sizes to ensure that cables always fit and alignment is not a problem

The rail on the side of the case is optional, but it's ideal for mounting it on a 2020/2040 aluminum extrusion v-slot profile. This includes the Ender 3 (v2).

The model with half a rail makes it possible to mount the case under the LCD panel.



Raspberry Pi 3B+ case (3, 2 & B+ also fit) - More Cooling, Less Material Used, Printer Mounting Rail

Case Without Mounting Rail

Case Cover

Case With Full Mounting Rail

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4967223.

Knowing myself I knew I'd need to print this again after finding better tools to use.

To avoid waste I made the side modular so I'd only need to print that again.

The uploaded design doesn’t include the spray bottle holder from the photo. I added that because I needed it. That’s the idea of making the design modular. I might upload it later.

Remixed from: https://www.thingiverse.com/thing:3877505

Ender 3 Tool Holder with Modular Side

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4993078.

Remixed from: https://www.thingiverse.com/thing:3256773

This remix makes it possible to mount your Pi on the right side of your Ender 3 v2 (maybe Ender 3 as well). 

Most people seem to mount their pi on the left side of their printer, but this takes up a lot of space. There's space behind the LCD, but bolts in the rails prevent the original design from sliding until it's tucked behind/under the LCD.

I simply cut away half of the rails, so the case slides over the bolts. It's still firmly mounted this way.

*In the photo's you see bolts on the side of the case. This is not the same design as in the uploaded STL. I made this modification for myself because I didn't have the right bolts when I wanted to print this. The only modification in the STL is the cut rails.*

Ender 3 v2 Raspberry Pi Dual Rails Enclosure Remix - Fits Under LCD

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4982592.

I designed this to empty the litter tray of our pet rabbits. It's a relatively large scoop, but I tried to use as little material as possible by making the thickness only 2.5mm while adding some reinforcements on some points. With 20% infill it feels very strong.

Inside width: 12.5cm
Inside length: 10cm
Inside Height: 5.5cm

Support is needed for the handle.

Wide Scoop

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4969844.

Meant to be a part of the Universal Camera Mount by RaffoSan, also remixed part of the mount: https://www.thingiverse.com/thing:2477180

The mount itself is directly taken from Catchy's design (the photo is also Catchy's): https://www.thingiverse.com/thing:2542192

I remixed the two designs together because I didn't want to take my c920 apart. Nor did I want to order a camera screw.

Caution:

All parts of RaffoSan's original design are for M4 bolts. Unless you have manually changed your parts to use M3 (like I have), download the M4 version.

Logitech C920 Screwless Mount for Raffosan Universal Camera Holder

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

teun95

Boltless Raspberry Pi 3B+ case (3, 2 & B+ also fit) - More Cooling, Less Material Used, Printer Mounting Rail

Ender 3 Tool Holder with Modular Side

Ender 3 v2 Raspberry Pi Dual Rails Enclosure Remix - Fits Under LCD

Wide Scoop

Logitech C920 Screwless Mount for Raffosan Universal Camera Holder