Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3901259.

Light weight Garmin inReach mini clip, designed from the ground up, to be as light, yet sturdy as possible. Designed to be used with the lanyard attachment, and supplied hex screw. 

Total weight (printed in PLA): 3 grams

Update: v4 is a bit more substantial, and a little more user friendly, enjoy! 

Edit: added a vertical clip to accompany this thing, found [here](https://www.thingiverse.com/thing:5407922). 

Constructive feedback welcome! 

No affiliation with garmin; Garmin®, the Garmin logo, Earthmate®, and inReach® are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. MapShare™ is a trademark of Garmin Ltd. or its subsidiaries.

Garmin InReach Mini Clip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2221139.

After much trial and error, and several revisions I finally got these little guys working great. The clip attaches securely to the (20mm) frame of the Prusa i3 (3DP-11-ATL), and the opposite side securely holds a 10mm LED strip! Once secured the angle of the LEDs is 23.5 degrees, which ended up being just right for almost every print I could throw at it.

To install, first clip it to the inside of the printer frame (facing the bed), on all 3 sides, hold up your LED strip to test for length, and cut to size. Then starting at one end, put the LED stip into one side of the clip, then the other side. It's a snug fit so you might have to use a little force, a fingernail, or plastic pry tool might help (but a screwdriver might damage the strip). Work your way around, one by one, until finished. 

Edit: The "LED Clip Final stl" is for mounting the LED strip on the outside of the frame. The "LED Clip Inner Final stl" is for mounting the LED stip on the inside of the frame, this is useful for places like where the control board and power supply mount to the frame (on the 3DP-11-ATL), and the outside clip wouldn't work. These inner clips are designed to be a tight fit, and twist into place, when installing them, take note of the 45 degree angle on the shaft, as the clip will only turn in the direction of the angle. Not the other direction. If you print it out, and give it a try, you'll see what I'm talking about. 

Enjoy! 

LED Clips - Prusa i3 (3DP-11-ATL) and others

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3857097.

Water bottle clip, designed to secure a standard water bottle to the webbing on a backpack shoulder strap, or belt. Similar to "Aqua Clip". This is the third revision, as I've managed to remove extra, unneeded material, and shave off a few grams; while still retaining rigidity. The textured finish on the clip (from 3D printing) adds a bit of security, so it doesn't slide out of the shoulder strap so easily, when bending over. I'd also recommend dipping the end of the clip in some kind of "rubber dip" for more security.  

Edit: v2 Recreated from the ground up. Should be a lot more substantial. 

For the gram weenie's out there:
Total weight, of printed clip (in PLA): 4 grams 
v2 Total weight, of printed clip (in PLA): ?

Constructive feedback welcome! 

No affiliation with Aquaclip, Aquaclip and Aquahook are registered trademarks used by GJC Products, Inc. under license. All rights reserved.

Bottle Clip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2179589.

Wire clips, designed to secure wires inside printer frame. Clips snap into place, and hold securely. 

Wire Clips - Prusa i3 (3DP-11-ATL) and others

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2275908.

Belt retainer designed to secure excess webbing on a backpack. This replaces the worn out elastic band that came with the backpack. Fits waist belts 1 1/2" wide. 

Once installed, there's a little bit of vertical wiggle room on the retainer, this was by design to allow the retainer to twist a little when used. When putting on the backpack I'd rather not have to worry that the belt retainer is stuck, this helps alleviate that. 

The clip will also hold more webbing, in case you need to double it back on itself. 

Belt Retainer

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2199672.

Soldering Iron stand base. The stand itself is nice, but tends to slide around on the table, this fixes that. Also included is a sponge holder, that keeps the sponge in place. The sponge holder is a little bit smaller than the sponge, once it's wet, this was by design, and holds the sponge firmly, and helps keep it moist! Also the sponge holder sits firmly on the stand. 

Designed for this soldering iron stand: http://a.co/d8WaXoD

Soldering Iron Stand

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5407922.

Designed a vertical mount to pair with a replacement clip I made for the Garmin InReach mini. Works perfectly with the [clip](https://www.thingiverse.com/thing:3901259). 

There is 2 versions, one has a clip that the InReach clip slides into horizontally, the other is a loop, of sorts, that the InReach clip slides into vertically; this one is more secure, but less convenient.

Both need supports everywhere because of their shape. 

Cheers 

No affiliation with garmin; Garmin®, the Garmin logo, Earthmate®, and inReach® are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. MapShare™ is a trademark of Garmin Ltd. or its subsidiaries.

Backpack verticle clip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2179514.

Filament Guide for Prusa i3 (3DP-11-ATL), and others. 
Mounts directly to extruded frame under filament holder. 

v2 has a larger, stronger ring, offering more support. 

Filament Guide - Prusa i3 (3DP-11-ATL) and others

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2539488.

Stand I designed in 123D (before it was shutdown) for a Nexus 7 tablet. It's designed to fit and [Anker Wireless QI Charger](http://a.co/gcelZgp). I made this specifically to display [Home-Assistant](https://home-assistant.io/) [Floorplan](https://github.com/pkozul/ha-floorplan). 

Pictures coming soon!

Nexus 7 Charging Stand

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2179582.

Under frame tool box, for various hand tools. 
Holds:
Scissors
Snips
Nail file
Allen wrenches
3D print removal tool: http://a.co/9WfhNgo
AA Maglite


Tool Box - Prusa i3 (3DP-11-ATL) and others

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2229675.

Control panel cover that actually fits! This is a large print, and I'd recommend printing it with the longer portion extending to the front & back of the bed (instead of side to side). 

When looking at the STL, with the cutout facing you..
The left side has a cutout for the SD card, as well as a cutout for the Z axis acrylic bracket. This is important when the control panel is attached to the frame, and slid all the way to the left. 
The right side has a small cutout for the screw that attaches the control panel to the frame, this was preventing the cover from sliding all the way down to the frame. 

Control Panel Cover - Prusa i3 (3DP-11-ATL) and others

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

strex

Achievements

Seedling

Garmin InReach Mini Clip

LED Clips - Prusa i3 (3DP-11-ATL) and others

Bottle Clip

Wire Clips - Prusa i3 (3DP-11-ATL) and others

Belt Retainer

Soldering Iron Stand

Backpack verticle clip

Filament Guide - Prusa i3 (3DP-11-ATL) and others

Nexus 7 Charging Stand

Tool Box - Prusa i3 (3DP-11-ATL) and others

Soldering Iron Stand

Tool Box - Prusa i3 (3DP-11-ATL) and others

Garmin InReach Mini Clip

Belt Retainer

Bottle Clip

Filament Guide - Prusa i3 (3DP-11-ATL) and others

Control Panel Cover - Prusa i3 (3DP-11-ATL) and others

Nexus 7 Charging Stand

Wire Clips - Prusa i3 (3DP-11-ATL) and others

Backpack verticle clip