Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3805417.

Very stable table filament spool holder.
It has perfect filament unwinding without jerking as a smaller central axis with spool centering is used.
The holder is designed in 2 variants of width 115mm and 138mm. I use 115mm most often.
The holder is completely printed including the pivot pin. No other material is needed if the stand is glued. If you will be screwing you need 8 pcs of screws M3x16mm or similar.
Everything is printed without support and without raft. The exception is the printing of the swivel pin, which must be printed in portrait and it is necessary to use a raft. Use a 80% filler on the pivot and set the filler ideally round.
Alexros's perfect all-round spool holder is used in the design. It is in 3 variants and I use the 60 mm version.
link is here.
https://www.thingiverse.com/thing:2112075

For construction bracket you need, 0.2-0.3 layer:
2x tv_sidewalls - fill 20%
2x tv_clutch_xxx mm - fill 20%
1x tv_pivot_8mm_xxx mm - fill 80%
1x Alexros's all-round spool holder of choice - 80% fill

A: screw mounting (recommended):
8x countersunk head screw M3 x16 mm
no glue needed

B: mounting by gluing:
1x plastic glue
screws are not needed

Recommendations for construction:
When using screws, drill the holes in the clutch with a 2.4mm drill. Then create the M3 thread.
Drill the holes in the side panel with a 3.5 mm drill bit.
Everything will be easier to install if your printer prints less accurately.
Use glue if you do not want to use screws.

If you do not want to print the swivel pin yourself, use any 8 mm diameter logs with a length of 115 or 138 mm. I have printed many of these holders and the printed pivot pin is reliable and fully functional.

Very stable table filament spool holder fully printed with swivel pin, universal size, mountable. For TRONXY, ANET and many other 3D printers.

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2539563.

Directional rotating pulley for filament. It is positioned upside down on the printer frame and the filament is passed over this pulley. This ensures good feeding of the filament. Filamet can be placed behind the printer on the desk and does not burden the printer frame. The rotating head follows the printhead.

guide rotating filament holder for TRONXY

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5029743.

Holder for pens, pencils, markers, etc. It is large enough for up to 36 pencils. The design allows you to combine multiple holders in one row, this is also suitable for a large number of markers.

If you need to change the size, use the resize to your appropriate size before slicing. Standard height is 61mm, width 103mm this equates to 100%.

The printing material is pretty much whatever you use. I used both PLA and PET. Printed with a layer height of 0.3mm due to the printing speed with a 0.4mm nozzle. This height is ideal for this print, but you can also use 0.2mm.

Scaling into the boss is not easy, after that you would have to use a weaker wall on the shorter side.This is not desirable because of the variability, so it is ideal to extend the table in one row, there the joint is perfect.  This joint can be glued together with, for example, double-sided tape or classic UHU plastic glue and the like.

If you like the print, post your prints here and show off the use in your home.

modular hexadecimal pencil holder - 36 pencils

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3800569.

Spare bed holder plate for TRONXY P802 or ANET A8 printer.
The board must be printed on a 3D printer that allows printing at least 222x222 mm. I printed it on my modified FLSUN allowing 310x310 printing.

The board has a height of 8mm and it is necessary to use at least 85% filler for strength. PLA material is sufficient, the plate is not thermally stressed and has sufficient strength.

The board has universal use for 3 or 4 bearing bushes. I use 4 bearings for better grip. I recommend this modification to everyone.

The belt attachment is shown in the figures. The belt holds plates in the slots. A tightening strap (2.5 mm) is used to tighten the belt. This is the mount for the P802. If ANET is used, the connection is the same.

If necessary, drill the holes with a 3.5mm or 4.5mm drill bit according to the hole.

TRONXY P802 or ANET A8 holder bed 220x220 8mm full printed

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

stanicio

Achievements

Seedling

Very stable table filament spool holder fully printed with swivel pin, universal size, mountable. For TRONXY, ANET and many other 3D printers.

guide rotating filament holder for TRONXY

modular hexadecimal pencil holder - 36 pencils

TRONXY P802 or ANET A8 holder bed 220x220 8mm full printed