Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4729813.

I remixed JomMa's thick spacer tile into a 1 tile bridge so you can add a support using an existing column. It can be placed at any height, just like a spacer.

As this introduces leverage, you will need to be cautious to not tip over the column. To counteract you can balance it out with another bridge to the opposite side or put 2 marbles inside the empty space to weigh it down.

Gravitrax column bridge spacer

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4729765.

This is a remix of nikutama05's filament storage box that holds 4 spools of filament with these changes:

* Designed for US-based 5/16 threaded rods. You need 2 of these that are each 12 inches long.
* Compatible with inexpensive 608 bearings (as used in skate/skateboard wheels). You need 4 bearings per spool (12 bearings total).
* Holes were cut in the very large side supports to significantly reduce filament use, while maintaining their strength.
* I added a new model "plugs" that are various heights to slide into the side supports and hold the rods tight and press the side supports against the storage box walls. This keeps the rods from shifting around.

You'll need to print:
* 2x Base2
* 32x Clip
* 16x Guide

Sterilite 20 qt Filament Enclosure - 5/16 inch remix

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4723450.

This is a remix of the base tile from alex80it, who has some really excellent Gravitrax designs. I split his model in Shapr3D to make it print in 2 pieces so it could be printed without supports and without needing any glue. I didn't even think to check to see if there are other remixes (there are!), but I see those take a different approach than mine. The biggest difference is I did not change ANY dimensions or otherwise modify the original model, so once put together this should be very close to dimensionally identical to alex80it's model, so if you've already printed a bunch of his models (such as the excellent elevation system), this model is completely compatible.

This needs to be printed at 0.2 mm resolution. Make sure to print the "bottom" upside down. Then simply carefully snap them together. While it's possible to use these without glue, I would recommend a tiny bit of CA before snapping the pieces together.

Gravitrax compatible 6-exit Base Tile - REMIX no supports

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4700558.

I have a Jeda "V2" wireless charging pad for my Tesla Model 3 that is not quite compatible with the iPhone 12 series of phones. They have since released a "V3" that is natively compatible. 

This adapter raises the resting place for the iPhone slightly so that the Qi charger lines up better on the V2. No need to replace the whole charging pad!

I have tested it on the iPhone 12 and 12 Pro. In theory it could help with any mobile phone that needs to be raised up on the charging pad by ~10 mm.

Meant for V2 of this charger: https://getjeda.com/product/jeda-wireless-pad/

Jeda V2 Tesla charging pad adapter for iPhone 12

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:752129.

When food scraps pile up in the sink you need a way to push them into the garbage disposal safely, even when it's on. This "disposal plunger" will push the scraps in, but cannot be pushed all the way through the opening.  

It will fit standard garbage disposal openings about 8.5 cm in diameter.   
Height is approximately 13.5 cm.  
*UPDATE Feb 2016* Added v1.1 with smooth sides all the way around.

No supports needed. I like a shell of 2 mm for strength and waterproofing with about 15% infill. 

My first design! :)

Disposal Plunger

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4718913.

This is a Fisher-Price Contrux plate that fits a square made of 4 long construction bars or 8 medium length bars. I don't believe this part exists in the Construx catalog, so 3D printing to the rescue! 

If your printer is calibrated it should snap in and hold itself in place. Designed for 0.2 layer heights. PLA works fine.

Construx plate

Activity related to collaborating with others on models

Likes, comments, and activity from your community