What makes this a point-down pencil holder? The hole profile has a tapered section (see picture), so the wood of the pencil contacts the holder, but no pressure is placed on the point.

See the souce here: https://github.com/sffubs/gridfinity/blob/master/pencil_holder.py

Gridfinity 1x1 point down pencil holder

pencil_holder.stl

Holds 4 Windsor & Newton half-pan watercolour blocks.

See the source here: https://github.com/sffubs/gridfinity/blob/master/watercolour_half_pan.py

Gridfinity 1x1 half pan watercolour block holder

watercolour_half_pan.stl

Holds 10 Windsor & Newton watercolour tubes.

See the source here: https://github.com/sffubs/gridfinity/blob/master/watercolour_tube_holder.py

Gridfinity watercolour tube holder

watercolour_tube_holder.stl

A spacer to allow a SRAM MTB Garmin mount (https://www.sjscycles.co.uk/cycle-computers/sram-quickview-mtb-garmin-gps-computer-mount-quarter-turn-twist-lock-318mm/) to be used with a 22.2mm handlebar.

It's designed to be printed in a flexible filament (I used a 95A TPU) with 75% gyroid infill.

Handlebar spacer for SRAM Garmin mount

garmin_mount_collar.stl

It seems I can't find the weights that Zack Freedman used in his original weighted base plate. In the UK, tyre weights come in 10g/5g sizes, approximately 24x20x4mm for the 10g size. This is a baseplate that accepts these weights.

This is basically my #gridfinity honeycomb shelf without the honeycomb parts, 0.5mm thicker, and with spaces for the weights. I've not tried to add any spaces for rubber feet (I haven't been able to source any that look good).

This is a parametric model. I've generated sizes here up to 7x7.

Source is here: https://github.com/sffubs/gridfinity/blob/master/weighted_base.py

Gridfinity weighted baseplate for 10g tyre weights

weighted_base_5_by_3.stl

There are many other #gridfinity pen/pencil holders. This one is mine. It's for 8mm pencils, with a 2.5 degree taper on the holes.

I've shortened the holes for the screws in the underside, since I only ever use the magnets.

This model was built using CadQuery, see the source code here: https://github.com/sffubs/gridfinity/blob/master/pen_pencil_holder.py

Gridfinity 1x1 pencil holder

pen_pencil_holder.stl

A #gridfinity block to hold a Derwent spritzer (spray bottle). The bottle has a super annoying habit of falling over on its own, so this block is really useful.

This model was built using CadQuery, find the source here: https://github.com/sffubs/gridfinity/blob/master/derwent_spray_holder.py

Gridfinity Derwent spritzer holder

derwent_spray_holder.stl

Windsor & Newton drawing ink bottle holders for #gridfinity.

Because I don't use the screwholes, they're only really deep enough to allow magnet installation. That allows the ink bottle to sit a little lower than it would otherwise.

This was built using CadQuery - source here: https://github.com/sffubs/gridfinity/blob/master/windsor_and_newton_ink_holder.py

Gridfinity Windsor & Newton ink bottle holder

windsor_and_newton_ink_holder.stl

CA glue bottle holders for #gridfinity for my preferred brand. For some reason I have a mixture of 0.5oz and 1.0oz bottles, so I've made blocks for both sizes.

Implemented in CadQuery. The source can be found at https://github.com/sffubs/gridfinity

Gridfinity zap-a-gap CA glue holder

zap_a_gap_ca_glue_1p0oz_holder.stl

This is a parametric #gridfinity compatible shelf forthe honeycomb storage wall: https://www.printables.com/model/152592-honeycomb-storage-wall

The model is written in CadQuery, and the source code is here: https://github.com/sffubs/gridfinity/blob/master/honeycomb_shelf.py

Honeycomb gridfinity shelf

gridfinity_shelf_6x1.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

sffubs

Achievements

Seedling

Explorer

Fan Favorite