Digitrax up7-template.stl

up7-template.stl

assortment-case-template.stl

Alexandre Chappel has published plans for a set of assortment boxes. This drill template is half of the holes needed. Flip this guide over to get the other half of the drill location.

gridfinity-rebuilt-microscope.stl

I've modded a 3x1x6 bin to have an open front with a slot for a microscope slide. Advantages over Zack's: 1) it is a single part, 2) the microscope slide fits tightly enough that it doesn't require glue. Disadvantage over Zack's: 1) it requires supports. It's a mod from kennetek's OpenSCAD bins, and I've submitted a PR to them.

Ryobi Multi-Tool (TDW025786) allen wrench holder

If you ask me, every tool that requires a tool to adjust it should have a place on the tool to hold the tool. Some Ryobi tools have this feature, but the Multi-tool (brushed -- the brushless may be different) does not.

Three 6mm x 2mm magnets are needed to hold the allen wrench into this holder. Very likely it will just fall out without them.

You can see from the photo how it is hot-melt-glued to the base of the tool, just above the battery. It's never proven to be in the way, so I'm happy with it.

Ryobi Multi-Tool allen wrench holder

ryobi-plunge-vacuum.stl

Joins the Ryobi Plunge Tile Cutter to the Ryobi 4.75 gallon vacuum.

Google_Pixel_3_XL case with Apple Magsafe

I cut into this case to let me put an [iPhone Magsafe magnet](https://www.amazon.com/dp/B09MKDPX2T) inside the case so I could attach it to an [Anker magnetic battery](https://www.amazon.com/gp/product/B099ZD3VK5/)

gridfinity flsun-q5 bedlevel.stl

Don't know where to put your bedlevel sensor for your FLSUN Q5? Print this out, along with my flsun-q5 grid, and put it there.

Gridfinity FLSUN Q5

Attach one or two of these to the top and/or left of your FLSUN Q5, print a few storage bins, and you can keep your tools close to your printer.

Source is at https://github.com/vector76/gridfinity_openscad

Gridfinity Avery Glue Stic

Zack's glue stick holders were either too large or too small. This one is just right for the Avery Glue Stic.

Source is at https://github.com/vector76/gridfinity_openscad

wemos-d1-mini.stl

Tophat Tools 

This is the core adapter, and is the only part which attaches directly to the DIN rail.

din_our_adapter.stl

rollers.stl

Inserts ball bearing rollers into the filament support for the FLSUN Q5. You'll need three standard skate bearings. They friction fit onto the part, and it friction (gravity) fits onto the filament holder.

You may need to file the bottom of the part to get it to fit into the rounded rectangles at the top of the filament holder. The bottom of the rounded rectangles is the first layer, which is often a little over-extruded.

stove-knobs.stl

A crude knob for my Kenmore stove. Needs to be curved on the top, but it fits nicely.

porter-cable-charger-mount.stl

My porter-cable battery charger didn't have any screw holes to mount it. This piece creates keyhole screw holes. I glued two of them into the charger, although they're a tight enough fit that wasn't necessary.

bora-wtx.stl

I bought a Bora-WTX track saw track and a generic fits-all sled. It didn't fit my Ryobi circular saw. So I built this piece to go between the saw and the track. Ball bearing slides would be better, but two of these at either ends of the saw work fine.

I made a hole for a small 1/16" x 1/4" magnet, but it's not strong enough, so I added zip ties and drilled two holes in each corner of the sled.

door molding

door-bottom-molding-corner.stl

porter-cable-battery-holder.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

New content from your premium memberships

Emails and messages from designers you follow

Get notified when someone purchases your models or memberships

russnelson

Achievements

Seedling

Trailblazer

Up and Coming