Holder for a hoodie/coat for my roughly 38.5mm x 38.5mm home workout rack.

Workout Coat Rack Holder v1.0

Workout Coat Holder v1.0.stl

Holder for two one-inch standard bar clamps for my roughly 38.5mm x 38.5mm home workout rack.

Workout Clamp Rack Holder v1.0

Workout Clamp Holder v1.0.stl

A simple dry eraser and three marker holder for my home gym rack (that being ~38.5mm long and wide).

Dry Erase Kit Rack Holder v1.0

Dry Erase Kit Holder v1.0.stl

Made these little end caps to fit the big and small areas on the 2" barbell rack I had got... 

Printed them out w/Overture Orange TPU at 15% Cubic Sub Infill (see .gcode below)

2-Inch Squat/Bench Rack End Caps

Large (Top Right) v1.1 (2.13.2024).stl

Felt like making the balsa wood school tower project a tad stronger... 

**Model Specs:**
Length: 6" (152.4mm)
Width: 6" (152.4mm)
Height: 8" (203.2mm)
Note: Wide Side Down!

**Print Details:**
Material: Overture's Green PLA
Nozzle: 210°C
Bed: 65°C
Walls/Top/Bottom: 3 Layers Thick
Infil: 33% Cubic Sub
Support: None
BP Adhesion: Brim (20 Lines // Distance 0.02mm)
GCode: Attached Below

1/8" PLA Truss Tower

Truss Tower 2.0.stl

The cover will snap on snugly (water tight seal). For the switch use a little hot glue to secure it as it's meant to be a lil loose. For the motor I would hot glue it down in the raised mount.

No need for supports as both should print fine (flip the cover upside down and the boat right-side up).

This is the electric kit I used if anyone is wondering...
https://a.co/d/5zyHeln

Custom Electric Boat - AP Physics 2 Project (Boat v4.1 - Cover v1.4)

The Boat [v4.1}.stl

My custom rook chess club trophy for getting 1st place in a tournament.

Rook 1st Place Chess Trophy

Chess Club Trophy v2 (12.14.2023).stl

A simple plate stopper that acts as a resting raised divit, preventing the heavy plates from rolling around or a dumbbell with plates from gilding off the table.

I recommend at least a 25% infill and PLA seemed to work just fine. 

I also attached my .gcode below too if anyone wants to take a peek.

1.5" Thick Home Gym Plate Stopper

Plate Stopper v1.4.stl

It's a flat charging stand with the word "bruh" on it lol.

"Bruh" Apple Watch Flat Charging Stand

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

rnewbold06

Achievements

Seedling

Explorer

Pinned models

1.5" Thick Home Gym Plate Stopper

1/8" PLA Truss Tower

Dry Erase Kit Rack Holder v1.0

Workout Coat Rack Holder v1.0

Workout Clamp Rack Holder v1.0

Dry Erase Kit Rack Holder v1.0

2-Inch Squat/Bench Rack End Caps

1/8" PLA Truss Tower

Custom Electric Boat - AP Physics 2 Project (Boat v4.1 - Cover v1.4)

Rook 1st Place Chess Trophy

1.5" Thick Home Gym Plate Stopper

"Bruh" Apple Watch Flat Charging Stand