Sovol SV05 - Power Supply Cover for Standard 215mm x 115mm x 50mm power supply

I had trouble with my printer reaching 245 degrees so I replaced the power supply with a 480W. The original power supply is thinner than most that are readily available so the original plastic didn't fit. The mounting screw locations on the side seemed to be standard. So after trying it and my printer running like a dream. I needed plastic. I used some features of a design someone else had done because I liked it ( I would love to give credit as soon as I can find it again I will update), but I made it fit the SV05 similarly to the original.
Markdown Enabled

Sovol SV05 - Power Supply Cover for Standard 215mm x 115mm x 50mm power supply

Sovol SV05 - Power Supply Cover.STL

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2134573.

Anet A8 X-Axis tensioner designed not to interfere with any of the other stock components.
requires an additional M3x6 Screw an M3x25, and an M3 nut pushed into the bottom of the bigger part.

Part V1A-Adjustable X belt_attach and adjust.STL thickens the wall on the bottom of the small part for those having issues printing.

Anet A8 X-Axis Tensioner

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5347103.

Bearing Slide for Half Height Uni-Strut. This uses 608 bearings on a 3D printed "carriage" that slides nicely in half height uni-strut. I used sheet metal screws to reinforce the bearing axles on the projects I used them for. I printed them in both PETG and PLA with good results. ABS should be good too. the center bearing has a slight spring action to it to allow for tolerance in the uni-strut. The center bearing should obviously be the non-load side.

Bearing Slide for Half Height Uni-Strut

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3334438.

This is a Holder I designed for the FYSETC TL Smoother. The Boards just snap in. It is capable of holding 5. The board fit is slightly loose intentionally I just used little pieces of brim to tighten them up. 

additional file added for TL-Smoother xr-120 by request only have listed dimensions to work with if you try it let me know 

FYSETC Smoother Board Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2053998.

The upper rolling pin belonged to my wifes 3x great grandmother. I decided it shouldn't be in a drawer.

Rolling Pin hooks

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3827239.

extended the duct down enough so it doesn't blow on the hot block causing thermal runaway

semi circular fan duct for Anet A8

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3390155.

Plug I made for 3/4″ thin walled EMT for my MPCNC project. I wanted to run wires through the tubes without fear of sharp edges.

3/4" Conduit Plug

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4295811.

I tried many of the ear saver gizmos others have posted and while they were all better than the pressure on the back of my ears none of them were comfortable enough for me. I must say however I do have a big head.


Ear-Eze - face mask ear relief

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3826888.

I really liked the original file from  10o  but I had a couple issues using it. The fan was a little too loose and that made it noisy. I easily broke the sensor mount with a small crash, and I felt the screw fit could be a little better with more support. So it doesn't look too much different but It works better for me. 


    X_PROBE_OFFSET_FROM_EXTRUDER -28 // X offset: -left +right [of the nozzle]
    Y_PROBE_OFFSET_FROM_EXTRUDER -37 // Y offset: -front +behind [the nozzle]

and

    LEFT_PROBE_BED_POSITION 17
    RIGHT_PROBE_BED_POSITION 192
    FRONT_PROBE_BED_POSITION 17
    BACK_PROBE_BED_POSITION 175


Anet A8 Fan and Sensor Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2053996.

Lamp shade I created to use with some hand turned wood lamps I made 

Lamp Shade small LED lamp

Plastic Product Design and development for 30 years, electronics Hobbyist, Photography hobbyist, former carpenter, and DIY fanatic.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

pmzielinski70