Canine Snout Mask, by Perihelion Prints

======

This playful canine snout mask is suitable for a masquerade party, as part of a dog/canine cosplay, or for a performance costume. Scaled to fit most adult heads.

For attachment to head, use elastic cord or ribbon. For fitting, place the mask on your face, lining it up with your nose and the sides of your face.

Ideally you will want to make a strap around your neck and another above your ears, as shown in the pictures. Measure how much ribbon you'l need to go around your neck from the bottom of the mask, then add a bit more and cut two equal halves. Glue one to each side of the mask, and use the leftover length to tie both pieces into a knot/bow behind your head. Repeat this process for the ear straps.

You may want to put a piece of foam on the inside of the mask, so it doesn't hurt your nose. You may also want to scale the mask down in the X axis by 5-10% if you have a narrower face.

Sculpted in Blender. STL and .blend files included. Dimensions in millimetres.

"demo_dress" used in demo render (https://skfb.ly/opoQD) by emilysa is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"ku" used in demo render (https://skfb.ly/oRRox) by warrio bhai is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Olivia free fire" used in demo render (https://skfb.ly/oJBwI) by Xman is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Realistic Female" used in demo render (https://skfb.ly/owqND) by Biviyt is licensed under Creative Commons Attribution-ShareAlike (http://creativecommons.org/licenses/by-sa/4.0/).

"SUNGLASSES FLOW" used in demo render (https://skfb.ly/6RBUq) by ChechoGimenez is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Susan" used in demo render (https://skfb.ly/HVnr) by lioness7 is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Yafiquí Llumú (Princess of the moon) V 1.0" used in demo render (https://skfb.ly/6WnVD) by IngWill is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

0.20mm layer height recommended.

Use supports where appropriate - organic supports recommended. Brim also recommended. Experiment with the orientation to minimize the amount of support material required.

15% infill tested. PLA recommended.

Filament Usage (estimated): 145g

Printing Time (estimated): 12h

^ Estimates based off slicing for Prusa MK3.9. Your mileage may vary.


Canine Snout Mask

snout_mask.stl

Crow Beak Mask, by Perihelion Prints

Loosely inspired by the beak of a crow, or the mask of a plague doctor, this elegant beak mask is suitable for masquerade party, as part of a corvid cosplay, or for a performance costume. Scaled to fit most adult heads.

For attachment to head, use elastic cord or ribbon. For fitting, place the mask on your face, lining it up with your nose and the sides of your face.

Ideally you will want to make a strap around your neck and another above your ears, as shown in the pictures. Measure how much ribbon you'l need to go around your neck from the bottom of the mask, then add a bit more and cut two equal halves. Glue one to each side of the mask, and use the leftover length to tie both pieces into a knot/bow behind your head. Repeat this process for the ear straps.

You may want to put a piece of foam on the inside of the mask, so it doesn't hurt your nose. You may also want to scale the mask down in the X axis by 5-10% if you have a narrower face.

Sculpted in Blender. STL and .blend files included. Dimensions in millimetres.

======

"Alicegravel C3drv Ex4 personnage 1" used in demo render (https://skfb.ly/6WM9y) by alicegravel is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Lady Sammy FREE" used in demo render (https://skfb.ly/onKEW) by LordSamueliSolo is licensed under Creative Commons Attribution-NonCommercial (http://creativecommons.org/licenses/by-nc/4.0/).

"Olivia free fire" used in demo render (https://skfb.ly/oJBwI) by Xman is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Realistic Female" used in demo render (https://skfb.ly/owqND) by Biviyt is licensed under Creative Commons Attribution-ShareAlike (http://creativecommons.org/licenses/by-sa/4.0/).

"SUNGLASSES FLOW" used in demo render (https://skfb.ly/6RBUq) by ChechoGimenez is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Yafiquí Llumú (Princess of the moon) V 1.0" used in demo render (https://skfb.ly/6WnVD) by IngWill is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"комбинезонКрасильникова Соняхтк2" used in demo render (https://skfb.ly/oCQ6H) by sonechka is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

======

0.20mm layer height recommended.

Use supports where appropriate - organic supports recommended. Brim also recommended. Experiment with the orientation to minimize the amount of support material required.

15% infill tested. PLA recommended.

Filament Usage (estimated): 135g

Printing Time (estimated): 10h

^ Estimates based off slicing for Prusa MK3.9. Your mileage may vary.

Crow Beak Mask

crow_beak_mask.stl

Cyberpunk Beak Gas Mask, by Perihelion Prints

Brave the post apocalypse in style, with this unique cyberpunk beak. Perfect for masquerade parties, cyberpunk cosplay, concerts/raves, or for a performance costume. Scaled to fit most adult heads.

For attachment to head, use elastic cord or ribbon. For fitting, place the mask on your face, lining it up with your nose and the sides of your face.

Ideally you will want to make a strap around your neck and another above your ears, as shown in the pictures. Measure how much ribbon you'l need to go around your neck from the bottom of the mask, then add a bit more and cut two equal halves. Glue one to each side of the mask, and use the leftover length to tie both pieces into a knot/bow behind your head. Repeat this process for the ear straps.

You may want to put a piece of foam on the inside of the mask, so it doesn't hurt your nose. You may also want to scale the mask down in the X axis by 5-10% if you have a narrower face. And be prepared to do a test print to check the fit.

Sculpted in Blender. STL and .blend files included. Dimensions in millimetres.

======

"Alicegravel C3drv Ex4 personnage 1" used in demo render (https://skfb.ly/6WM9y) by alicegravel is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Balance" used in demo render (https://skfb.ly/oHCCz) by Stan is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"CyberPunk Girl" used in demo render (https://skfb.ly/oK6CV) by Toni García Vilche is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"demo_dress" used in demo render (https://skfb.ly/opoQD) by emilysa is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"ku" used in demo render (https://skfb.ly/oRRox) by warrio bhai is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Lady Sammy FREE" used in demo render (https://skfb.ly/onKEW) by LordSamueliSolo is licensed under Creative Commons Attribution-NonCommercial (http://creativecommons.org/licenses/by-nc/4.0/).

"SUNGLASSES FLOW" used in demo render (https://skfb.ly/6RBUq) by ChechoGimenez is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Yafiquí Llumú (Princess of the moon) V 1.0" used in demo render (https://skfb.ly/6WnVD) by IngWill is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

======

0.20mm layer height recommended.

Use supports where appropriate - organic supports recommended. Brim also recommended. Experiment with the orientation to minimize the amount of support material required.

15% infill tested. PLA recommended.

Filament Usage (estimated): 105g

Printing Time (estimated): 8h30m

^ Estimates based off slicing for Prusa MK3.9. Your mileage may vary.

Cyberpunk Beak Gas Mask

cyberpunk_beak_mask.stl

Chic Beak face mask, by Perihelion Prints

This unique "chic beak" mask offers a minimalist, architectural take on the classic plague doctor mask.

The plague doctor mask began its rise to prominence and infamy in 17th century Europe. It is unclear exactly when the full beak mask came to be, but they were popularized as an early form of protective equipment by the eccentric French royal physician, Charles de Lorme. The plague doctor was also a recurring character in Italian theatre, whose presence personified the fear of death and disease. To this day, the beaked mask remains a mysterious article, full of personality and symbolism.

This modern half-face interpretation is a versatile fashion accessory, suitable for parties, masquerade balls, cosplay, or as part of a performance costume. It can also be used as a stylish cover for a disposable face mask.

The nose cavity is large enough to hold something sweet-smelling. Although it will not protect you from "bad air" as was the medieval theory, there's nothing stopping you from putting something like a sprig of lavender, dried flowers, or a drop of peppermint oil for aromatherapeutic purposes.

For attachment to your face, you will need a bit of cord/ribbon. Ideally, you could cannibalize the straps from a disposable face mask. Hot glue works well to attach the straps to the mask. You may not need that much length on the ear loops, since the sides of the mask will be close to your ears. Refer to the reference pictures.

Alternative solutions include pieces of ribbon that tie behind your head or wearing a disposable face mask underneath the beak mask, passing its straps through the holes in the beak mask.

Scaled to fit most adult heads.

You may want to scale the mask down by 5-10% (in all dimensions) depending on the size of your head. In addition, if your face is narrow, you may want to scale a bit more in the X axis.

Be prepared to do a test print to check the fit, especially around your nose and ears. Compatibility with glasses and/or disposable face masks is not guaranteed on your first attempt, but may be possible with proper scaling.

Sculpted in Blender. STL and .blend files included. Dimensions in millimetres.

======

0.20mm layer height recommended.

Use supports where appropriate - organic supports recommended as they are generally easier to remove. Brim also recommended. Experiment with the orientation to minimize the amount of support material required.

15% infill tested. PLA recommended.

Filament Usage (estimated): 70g

Printing Time (estimated): 3h45m

^ Estimates based off slicing for Prusa MK3.9. Your mileage may vary.

If you find the mask is too thin, you can edit the Blender file to increase its thickness (look for the "Solidify Modifier"). And feel free to reach out with any questions.

Chic Beak Face Mask

chic_beak.stl

Streamlined Breather Mask, by Perihelion Prints

======

This architectural face mask mimics the look of a sci-fi respirator mask. Suitable for masquerade parties, cyberpunk cosplay, concerts/raves, or as a cover for a disposable face mask.

Despite being fully closed at the front, you should be able to breathe through the chin-level opening at the back.

Please note: It should be obvious, but this mask does not offer respiratory/medical protection. It is only a fashion accessory. Although you may be able to fit a disposable face mask behind it.

======

For attachment to head, use elastic cord or ribbon. For fitting, place the mask on your face, lining it up with your nose and the sides of your face.

Ideally you will want to make a strap around your neck and another above your ears, as shown in the pictures. Measure how much ribbon you'l need to go around your neck from the bottom of the mask, then add a bit more and cut two equal halves. Glue one to each side of the mask, and use the leftover length to tie both pieces into a knot/bow behind your head. Repeat this process for the ear straps.

======

Scaled to fit most adult heads.

Be prepared to do a test print to check the fit, especially around your nose and chin.

Sculpted in Blender. STL and .blend files included. Dimensions in millimetres.

======

"Ameri" (https://skfb.ly/YZuP) by reizibarrientos is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Arianna Iglesias" used in demo render (https://skfb.ly/p6Kun) by Jungle Jim is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"BATIK HEADBAND SERI" used in demo render (https://skfb.ly/onyBn) by eeelabvisual is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Bikini Girl" (https://skfb.ly/owoBv) by KillaKali1991 is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Dr Sofia - Talking" (https://skfb.ly/oUTzL) by p143467 is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Free Test Character Asuna" (https://skfb.ly/oruvL) by MSGDI is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

======

0.20mm layer height recommended.

Use supports where appropriate. Depending on the orientation, you may not need that much support material, and you may be able to get away with regular (non-organic) supports.

15% infill tested. PLA recommended.

Filament Usage (estimated): 40g

Printing Time (estimated): 2h

^ Estimates based off slicing for Prusa MK3.9. Your mileage may vary.

======

If you find the mask is too thin, you can edit the Blender file to increase its thickness (look for the "Solidify Modifier"). And feel free to reach out with any questions.

Streamlined Breather Mask

streamlined_breather_mask.stl

Cyborg Experiment Mask by Perihelion Prints

Ready to print and wear or display. Perfect for parties, cosplay, or as part of a performance costume.

======

Scaled to fit most adult heads. Although it may be a bit big on smaller heads, as shown. You may want to experiment with scaling it down 5-10% to fit your face. Test print recommended.

For attachment to head, use elastic cord or ribbon. Hot glue should work. For fitting, place the mask on your face. Measure how much ribbon you'll need to go around your head, starting from just above the middle "bars" around your ears. Then add a bit more and cut two equal halves. Glue one to each side of the mask, and use the leftover length to tie both pieces into a knot or bow behind or head. Or you can edit the file to come up with your own solution.

Sculpted in Blender. STL and 3MF files included. Dimensions in millimetres.

======

"654230039_avatar_sdk" used in demo render (https://skfb.ly/oZCrV) by 654230039 is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"CBTUP409QH2DAVG5Z8RFOUUYB" used in demo render (https://skfb.ly/pxFuJ) by VITU6018 is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Gothic Girl" used in demo render (https://skfb.ly/oPEAI) by Toni García Vilche is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

======

0.20mm layer height recommended.

Works with PLA, PETG, etc.

Filament Usage (estimated): 58m

Printing Time (estimated): 4h45m

^ Estimates based off slicing for Prusa MK3.9. Your mileage may vary.

======

Organic supports are recommended, as shown in the pictures, provided your slicer supports them.

There is an optimized 3MF included that should be far easier to slice than the STL it was based on. However, your results may vary since the polygon count is far lower, and some small features may be decimated beyond recognition. It should still print absolutely fine, though, and in my tests the artifacts of decimation weren't present in the final print.

Feel free to reach out with any other questions or concerns, prior to or after purchase.

Cyborg Experiment Mask

cyborg_experiment_mask.3mf

Wasteland Harness Mask by Perihelion Prints

Includes 9 variants:

Open Nose
Open Nose, Short Middle Piece
Open Nose and Grill
Closed Nose and Grill
Semi-Open Nose and Grill
Closed Nose
Semi-Open Nose
Semi-Open Nose and Lips
Closed Nose and Lips

======

Scaled to fit most adult heads. It's a fairly quick print (with organic supports) so you may want to do a test print or two to confirm fit.

For attachment to head, use elastic cord or ribbon. For fitting, place the mask on your face, lining it up with your nose and the sides of your face.

Ideally you will want to make a strap around your neck and another above your ears, as shown in the pictures. Measure how much ribbon you'l need to go around your neck from the bottom of the mask, then add a bit more and cut two equal halves. Glue one to each side of the mask, and use the leftover length to tie both pieces into a knot/bow behind your head. Repeat this process for the ear straps.

Sculpted in Blender. STL and .blend files included. Dimensions in millimetres.

======

0.20mm layer height recommended.

Use organic supports for best results.

15% infill tested. PLA recommended.

Filament Usage (estimated): 35-45g (based on variant)

Printing Time (estimated): 2h45m - 3h30m (based on variant)

^ Estimates based off slicing for Prusa MK3.9. Your mileage may vary.

Wasteland Harness Mask

Wasteland_Harness_Mask_-_with_Nose_and_Lips.stl

Low-Poly Face Mask by Perihelion Prints

Can be worn on its own, or as a cover for a disposable face mask. Should be obvious, but this is only a fashion/costume accessory, and does not offer any medical/particulate protection.

Comes with a quad/rectangular variant and a triangulated variant. Each variant includes a version with holes for the straps of a disposable face mask.

Designed in Blender. STL and .blend files included. Dimensions in millimetres.

Scaled to fit most adult heads, but you may want to do a test print to confirm fit, and scale accordingly. You may also want to put a piece of form on the nose section, or it might pinch your nose a bit.

For attachment to your head, there are many options. If wearing on top of a disposable face mask, use its ear straps (print the variant that comes with slots at the side for the straps to fit through). Alternatively, you can hot glue some ear or head straps on the sides as shown in the pictures.

======

0.20mm layer height recommended.

Organic supports recommended.

PLA/PETG recommended.

Filament Usage (estimated): 55g

Printing Time (estimated): 3h30mm

^ Estimates based off slicing for Prusa MK3.9. Your mileage may vary.

Low-Poly Face Mask

low_poly_mask_triangulated_with_holes.stl

Moving Beak Mask by Perihelion Prints

This beak mask can open and close, with the help of two elastic bands and a bit of hardware.

Scaled to fit medium to large adult heads.

If your head is a bit on the smaller side, try scaling it down by 10-15% in the vertical/Z direction and trying a test print. The most important parts are how it fits around your nose, how much space it leaves on the sides of your face, and how it fits around your chin. It should be fairly comfortable, without pinching your nose or the sides of your face, and you should be able to open it fairly wide by moving your jaw. Although it takes a bit to make it move, it won't open and close through normal regular-volume speech.

For attachment to head, use elastic cord or ribbon. Hot glue should work. For fitting, place the mask on your face, lining it up with your nose. Measure how much ribbon you'll need to go around your head, then add a bit more and cut two equal halves. Glue one to each side of the mask, and use the leftover length to tie both pieces into a knot or bow behind or head. Or you can edit the file to come up with your own solution.

When the jaw is open, your mouth will be visible. If this isn't what you want, you could try wearing a neck gaiter over your mouth and nose, or adding some opaque fabric to the interior of the mask, giving it enough slack so it doesn't tear when the jaw opens. You may also experiment with wearing a disposable face mask underneath, but it seems like anything that covers your chin affects your ability to open and close the mask. Ultimately some experimentation may be necessary to come to an ideal solution.

Sculpted in Blender. STL and .blend files included. Dimensions in millimetres.

======

"Korean style female" used in demo render (https://skfb.ly/pu8so) by sxnneh is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

======

0.20mm layer height recommended.

Organic supports recommended.

PLA/PETG recommended.

Prints in two parts, upper and lower. To minimize supports and filament usage, refer to the preview pictures for suggested part orientations.

Filament Usage (estimated): 84g (36g for upper, 48g for lower)

Printing Time (estimated): 5h30m (2h30m for upper, 3h for lower)

^ Estimates based off slicing for Prusa MK3.9. Your mileage may vary.

For assembly, you'll need two small (or medium-sized) thin elastic bands, as well as some kind of 3mm bolts or screws.

Recommended to use two M3x6mm screws. Please note that the upper part should go on top of the lower part, with its screw hole protrusions sticking out as shown.

The elastics will go between the two sets of pegs on the inside of the printed pieces. If you have a shorter elastic, as long as you can still open the jaw, you can just keep it between the pegs. Otherwise you may be able to use the screw head as a third peg, as shown in the pictures.

It's possible after extended use that you'll wear out the holes and the screws will fall out. In that case you can experiment with slightly longer screws and some M3 nuts to keep them in place. You could also use any kind of 3mm spacer, or print a small 3mm cylinder to fit in the holes.

If you have any assembly or post-processing questions prior to or after your purchase, or if you have any suggestions for improving the design, feel free to reach out.

Moving Beak Mask

moving_beak_mask_top.stl

Urban Ninja Face Shield by Perihelion Prints

Can be worn on its own or as a cover for a disposable face mask. Suitable as a standalone accessory or to add flair to a masked cosplay outfit.

Scaled to fit most adult heads, but you may want to do a test print to confirm fit, and scale accordingly.

For attachment to your head, there are many options. If wearing on top of a disposable face mask, use its ear straps and fit them through the slots on the sides (if you've printed a version with slots). Alternatively, you can hot glue some ear or head straps on the sides.

Comes with a version with and without slots in the sides for the straps of a disposable face mask.

Designed in Blender. STL and .blend files included. Dimensions in millimetres.

Obviously this "face shield" is for aesthetics only, and does not provide meaningful protection from dust, pollution, or airborne pathogens.

======

"3D_female_free_content_part0" used in demo render (https://skfb.ly/pv9xE) by VITU6018 is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"654230039_avatar_sdk" used in demo render (https://skfb.ly/oZCrV) by 654230039 is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Angelica" used in demo render (https://skfb.ly/6ouNX) by DarkNik is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Bikini Girl" used in demo render (https://skfb.ly/owoBv) by KillaKali1991 is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Character Lyna" used in demo render (https://skfb.ly/6QUtO) by Sunny25 is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Gothic Girl" used in demo render (https://skfb.ly/oPEAI) by Toni García Vilche is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Kimono Girl" used in demo render (https://skfb.ly/p87OH) by Hellcutter is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Korean style female" used in demo render (https://skfb.ly/pu8so) by sxnneh is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

======

0.20mm layer height recommended.

Organic or "snug" supports recommended. You may want to adjust the orientation so it prints faster and requires less support. See slicer preview images for an ideal orientation.

PLA/PETG recommended.

Filament Usage (estimated): 55g

Printing Time (estimated): 3h

^ Estimates based off slicing for Prusa MK3.9. Your mileage may vary.

Urban Ninja Face Shield

urban_ninja_face_shield.stl

Fox Snout Mask by Perihelion Prints

======

Snout mask based on the muzzle of a fox, complete with a mouth and nose. Suitable as the basis for a fox or other canine costume. Could be worn as-is, or in combination with "ears" and/or face paint.

Scaled to fit larger adult heads, but you may want to do a test print to confirm fit and scale accordingly.

For attachment to your head, you can attach cord or ribbon. Hot glue works well. Ideally you will want four roughly equal strips, that you can attach to the corners of the mask, leaving you with a chin strap and a strap you can tie around the back of your head.

Designed in Blender. STL and .blend files included. Dimensions in millimetres.

======

"Cat Ears" used in demo render (https://www.printables.com/model/35076-cat-ears) by RoboMagus is licensed under Creative Commons CC0 - Public Domain license (https://creativecommons.org/share-your-work/public-domain/cc0/)

"demo_dress" used in demo render (https://skfb.ly/opoQD) by emilysa is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

======

0.20mm layer height recommended.

Tested with "snug" supports. Organic supports will take longer but may come off cleaner. This print in particular was with older filament, so it's not always that burred.

PLA/PETG recommended.

Filament Usage (estimated): 120g

Printing Time (estimated): 7h

^ Estimates based off slicing for Prusa MK3.9. Your mileage may vary.

After printing, you may want to sand, prime, and paint it, or you can keep it in the base colour.

Fox Snout Mask

fox_snout_mask.stl

Spiky Punk Mask by Perihelion Prints

Can be worn by itself or as a cover for a disposable face mask. Suitable as a standalone accessory or to add flair to a masked cosplay/rave outfit.

Scaled to fit most adult heads, but you may want to do a test print to confirm fit, and scale accordingly. You may also want to put a piece of form on the nose section, or it might pinch your nose a bit.

For attachment to your head, there are many options. If wearing on top of a disposable face mask, use its ear straps and fit them through the slots on the sides (if you've printed a version with slots). Alternatively, you can hot glue some ear or head straps on the sides.

Comes with a version with and without slots in the sides for the straps of a disposable face mask.

Designed in Blender. STL and .blend files included. Dimensions in millimetres.

======

"Angelica" used in demo render (https://skfb.ly/6ouNX) by DarkNik is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Cristy" used in demo render (https://skfb.ly/pwsBM) by rickcomics is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Face Mask 3D Model (Free)" used in demo render (https://www.artstation.com/artwork/Oowr98) by Aaron Bookout on Artstation.

"Gothic Girl" used in demo render (https://skfb.ly/oPEAI) by Toni García Vilche is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Shang Hai Style Lady in glasses" used in demo render (https://skfb.ly/pxyHX) by aribb is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

======

0.20mm layer height recommended.

Organic supports recommended. You can experiment with other support types if you want to cut down on print time and filament usage, but organic supports will come off the easiest and should lead to the best results.

PLA/PETG recommended.

Filament Usage (estimated): 105g

Printing Time (estimated): 10h30m

^ Estimates based off slicing for Prusa MK3.9. Your mileage may vary.

After printing, if you're really patient and careful, you may be able to paint the spikes a different colour from the mask base. Unfortunately they can't be easily separated for multi-colour printing, but you're welcome to try. Feel free to reach out with any questions prior to or after purchase

Spiky Punk Mask

spiky_punk_mask_with_slots.stl

Geometric Cutout Face Mask by Perihelion Prints

Can be worn by itself or as a cover for a disposable face mask. Suitable as a standalone accessory or to add flair to a masked cosplay outfit.

Scaled to fit most adult heads, but you may want to do a test print to confirm fit, and scale accordingly. You may also want to put a piece of form on the nose section, or it might pinch your nose a bit.

For attachment to your head, there are many options. If wearing on top of a disposable face mask, use its ear straps and fit them through the slots on the sides (if you've printed a version with slots). Alternatively, you can hot glue some ear or head straps on the sides.

======

Comes with multiple variants:

Blocky or Smooth
With Slots for Face Mask Straps or Without Slots
Then each variant has the following cutouts available:

Triangles
Squares
Pentagons
Hexagons
Heptagons
Octagons
Circles
Designed in Blender. STL and .blend files included. Dimensions in millimetres.

======

"Face Masks" used in demo render (https://skfb.ly/6ULKz) by ZeKa Arts is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Indian Office Woman" used in demo render (https://skfb.ly/oLUUo) by Nodeaxis Interactive is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Pink irregular waisted halter dress" used in demo render (https://skfb.ly/oJr7M) by Style3D CG is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Pocolov Hair 05" used in demo render (https://skfb.ly/6WQwq) by pocolov is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

======

0.20mm layer height recommended.

Organic supports recommended. You can experiment with other support types if you want to cut down on print time and filament usage, but organic supports will come off the easiest and should lead to the best results.

PLA/PETG recommended.

Filament Usage (estimated): 55g

Printing Time (estimated): 6h

^ Estimates based off slicing for Prusa MK3.9. Your mileage may vary. Based on the Blocky Circles with Slots design, others have different (but similar) filament usages and print times.

Geometric Cutout Face Mask

geometric_cutout_face_mask.blend

Mouth Cage Face Mask by Perihelion Prints

Can be worn by itself or as a cover for a disposable face mask. Suitable as a standalone accessory or to add flair to a masked cosplay outfit.

Scaled to fit most adult heads, but you may want to do a test print to confirm fit, and scale accordingly. You may also want to put a piece of form on the nose section, or it might pinch your nose a bit.

For attachment to your head, there are many options. If wearing on top of a disposable face mask, use its ear straps and fit them through the slots on the sides of the cage mask. Alternatively, you can hot glue some ear or head straps on the sides.

======

"Crossbow Lady" used in demo render (https://skfb.ly/oLGSN) by MoonCat is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Face Masks" used in demo render (https://skfb.ly/6ULKz) by ZeKa Arts is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Indian Office Woman" used in demo render (https://skfb.ly/oLUUo) by Nodeaxis Interactive is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Pink irregular waisted halter dress" used in demo render (https://skfb.ly/oJr7M) by Style3D CG is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

"Pocolov Hair 06" used in demo render (https://skfb.ly/6U9XS) by pocolov is licensed under Creative Commons Attribution (http://creativecommons.org/licenses/by/4.0/).

======

0.20mm layer height recommended.

Organic supports recommended. You can experiment with other support types if you want to cut down on print time and filament usage, but organic supports will come off the easiest and should lead to the best results.

PLA/PETG recommended.

Filament Usage (estimated): 56g

Printing Time (estimated): 5h15m

^ Estimates based off slicing for Prusa MK3.9. Your mileage may vary.

Mouth Cage Face Mask

mouth_cage_mask.stl

Mouth Masks

Chinese-Style Theatre/Masquerade Mask

chinese_style_theatre_mask.blend

Bird Masquerade Mask with Feathers and Beak

bird_mask.blend

snout_mask.blend

Perihelion Prints - the Apex of Wearable Design

Activity related to collaborating with others on models

Likes, comments, and activity from your community

New content from your premium memberships

Emails and messages from designers you follow

Get notified when someone purchases your models or memberships

perihelion_prints