NOTE: There may be some loss of fidelity of the multigrid base as there are no released STEP files for remix which could limit expected functionality.

This will hold up to 4 acrylic paint bottles in three multigrid base in a 1x3 grid. You place the paint bottles cap down.

Multiboard Multigrid Acrylic Paint Holder

MultiBoardPaint v14.stl

Remixed from the ever popular [USB SD and MicroSD holder for wide USB sticks ](https://www.thingiverse.com/thing:2637487)by Lalo_Solo. This attaches to multiboard using a push fit connection. There is a left and right model. Print whichever you choose but if you need more storage these are designed and spaced to leverage two adjacent multiboard openings.

MultiBoard Memory Card Storage, Expandable!

MultiBoardMemoryCardRight.stl

A simple way to store things that "plug in" on your multiboard. My specific use case is to store AA/ AAA battery chargers next to my rechargeable batteries. This supports US  plugs and can accommodate polarized or grounded plugs. It attaches to multiboard using a simple push fit connector. It's recommended you insert/ remove a plug a few times to ensure proper fitment before placing on your board. 

Multiboard Wall Plug Mount (US)

MultiboardWallPlug v4.stl

These are battery holders for Multiboard and Hex (HSW) Wall. Note: these leverage [Multiconnect ](https://www.printables.com/model/716558-multiconnect-generic-connector-for-your-board)for attachment to the Multiboard and Hex (HSW) wall. There is a file for AAAA, AAA, AA, C and D batteries. You should be able to print upright with no supports. 

For the smaller battery holders you may find it easier to eject the battery from the top by pushing up via the finger hole at the base.

If you need to store a charger for batteries consider [this multiboard adapter. ](https://than.gs/m/999813)

Multiboard & Hex (HSW) Wall Battery Holder Using Multiconnect

MultiBoardBatteryAAA.stl

MultiBoardBatteryAA.stl

MultiBoardBatteryCBattery.stl

MultiBoardBatteryDBatterystl.stl

MultiBoardBatteryAAAA.stl

Simple push fit holder for multiboard. Designed for tactical flashlight or anything else with a diameter of 35mm or less. Two versions available. One with an additional hook on the front to hang a light with a lanyard or hook.

Multiboard Tactical Flash Light Holder

MultiBoardMountFlashlightNoHook.stl

MultiBoardMultiMountFlashlightWHook.stl

This is designed to hold an aerosol can, canned air, etc. on your multiboard. It is attached via the overly strong pegboard clips and holds the cans at an angle. Two different models are provided, one with built-in support and one without if you'd like to add your own. It should be printed on the side to provide the most strength for the pegboard clips. The model is not oriented this way. The pre-supported model may have the slightest of sagging at the top of the cylinder but will print successfully on a Creality K1. To remove the supports around the pegs, use your side cutters to gently separate the supports from the pegs. It requires three horizontal pegboard spaces to clip in and is designed so you can butt them up horizontally to store multiple cans with no gaps in between (see pictures). Correct vertical spacing will have three open peg board holes between two of these holders.  There is a small triangular hole in the model for any spray nozzles your can's may have.

Multiboard Aerosol Can Holder Pegboard Attachment

MultiBoardCannedAir_NoSupports.stl

MultiBoardCannedAirSupports.stl

This is a 50 mm long piece of 20 20 extrusion attached to a big thread for Multiboard. I had some existing 3d printer parts holders that slid into 20 20 extrusions. Rather than rebuild the parts holder I simply made this. Remixed from [https://www.thingiverse.com/thing:741325](https://www.thingiverse.com/thing:741325).

This is the [tool holder ](https://www.thingiverse.com/thing:3457767)I use. 

Multiboard 20 20 Extrusion Large Screw

MultiBoard20_20_Extrusion.stl

Available in a single or double configuration. This part allows you to store 2 scissors, needle nose pliers or side cutters depending on size. It attaches with a [Small Thread Flat Head T Bolt](https://thangs.com/search/%22MB57%22%20%22MB58%22%20creator%3A%22Keep%20Making%22?scope=thangs&view=compact-grid) into a peg board hole in the [multiboard](https://thangs.com/category/Multiboard). Use the [multitool ](https://thangs.com/designer/Keep%20Making/3d-model/Multitool-974180)to screw in the T bolt. Print with the rectangular openings on the build plate, no supports needed. 

Multiboard Scissor Holder Screw In

MultiBoardScissorsDbl.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

ne2000

Achievements

Novice Maker

Seedling

Voyager

Fan Favorite