Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4183031.

The OEM Crock Pot handles are made of thin polycarbonate that turns brittle and cracks over time.This is a durable replacement that should hold up over time when printed with PETG and using a stainless steel bolt and nut.

Requires a stainless steel 25mm M5-0.8 bolt and nut.Examples:
- https://www.menards.com/main/hardware/fasteners-connectors/bolts/cap-screws-hex-bolts/midwest-fastener-reg-5mm-0-8-x-25mm-stainless-steel-grade-18-8-hex-cap-screw-1-count/87495/p-1444440173582-c-8730.htm
- https://www.menards.com/main/hardware/fasteners-connectors/nuts/hex-jam-nuts/midwest-fastener-reg-5mm-0-80-stainless-18-8-coarse-thread-hex-nut-2-count/87524/p-1444440175780-c-8915.htm

The bushing/washer may come in different sizes to fit the hole in the glass lid. I have provided 6mm and 8mm versions to fit your needs.

The hexagonal plug is optional, but helps finish off the look of the handle. With the natural elephant foot effect of most 3D printers, you can achieve a tight fit by tapping it into place with a small hammer until it's firmly seated, then sand it flush. You could also optionally sand off the layer lines and tight angles of the bevels if the 3D printed look doesn't suit you.

These models use a sacrificial layer above the hex cutouts to avoid the use of supports during printing.

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/gya3sz6oW6J

Crock Pot Slow Cooker Lid Handle

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4116936.

9mm Luger 9x19mm Parabellum Snap Cap Dummy Training Bullet Cartridge Round w/ TPU Firing Pin Cushion

Print the cartridge/bullet in PETG or ABS, and the firing pin cushion out of TPU. Choose a nice bright ridiculous color so you know it's not a real round of ammunition. Has an internal hole for pushing the plug out with a straightened paperclip or a toothpick.

A pull of the trigger makes a nice soft thud instead of a click when using the TPU plug.

Also added a rimless version if you want the round to stay in the chamber when racking the slide.

EDIT 3/14/2020: Since the original rimless version didn't grip the barrel very well, I also uploaded a version with a ridge for an o-ring, as well as a TPU o-ring to go with it. Now it stays put until you push it back out with a pencil or something similarly small.

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/eV76ymCG20H

9mm Luger 9x19mm Training Bullet w/ TPU Firing Pin Cushion

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3713356.

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/3WAnl79syLU

1/2" NPT Nipple

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4336570.

This is a GoPro style mount for a scissor lamp stand. Meant to be paired with the GoPro mount for a Blue Yeti mic (and others with a 5/8" mount). See: https://www.thingiverse.com/thing:3199914

Edit 11/23/2020: Uploaded an STL without the sacrificial bridge for those wanting to print this on a resin printer.

This thing was made with Tinkercad. Edit it online https://v1.tinkercad.com/things/0Njnjg5dP3n

Scissor Lamp to GoPro Style Mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3346614.

The spigot on Reliance water jugs are notorious for not sealing well, and/or cracking due to over-tightening due to poor alignment of the spigot. This gasket serves as both a seal, and wiggle room for rotating the spigot another 180 degrees once it has sealed, preventing stress fractures. Must be printed with TPU flexible filament to allow for proper compressibility and give.

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/4ZCCp6dSXTE

Reliance Water Jug Spigot TPU Tap-to-Cap Gasket

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3199914.

Was playing around with using the Modular Mounting System (https://www.thingiverse.com/thing:2194278) as a mic mount for my Blue Yeti mic. Needed a mic stand attachment that would work with it, so I made this. Also leaves plenty of clearance for the Blue Yeti USB cable strain relief (https://www.thingiverse.com/thing:2806301)

This mount itself is very sturdy, however the arms from the modular mounting system generally aren't capable of holding that much weight, especially over any significant distance (too much rotational force on the joints). ~~Regardless, hoping someone else finds use for this.~~ EDIT: I created a scissor lamp mount for this as well that works well since there's no long plastic arm to flex under the load. Get it here: https://www.thingiverse.com/thing:4336570

I printed it with Amazon PETG using 4 walls and 6 upper and lower layers at 0.2mm. Threads in perfectly and feels very durable. EDIT: I found that using a 1.0mm nozzle seems to help with layer adhesion.

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/77fcTlOrpmJ

Blue Yeti 5/8" Mic to GoPro-Style Mount Adapter

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4927432.

Based on https://www.thingiverse.com/thing:3585059 and remixed in Tinkercad (https://www.tinkercad.com/things/lfhW2cqGIi8). Scaled original to 87.7% on the X and Y axis to make the internal opening just slightly larger than 91mm, giving it a nice snug fit on the Fluidmaster flapper valve assembly nut. Printed mine out of PETG which held up like a champ. This sucker was hard to get off!

Needed this to get the nut off to replace the rubber foam gasket seal which had started leaking. I plan to model a mold for a replacement gasket made of two-part silicone which should last for ages. Link for that coming soon.

3 Inch Fluidmaster Flapper Valve 91mm Wrench

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4517177.

This clips on to the stock CR10-S filament sensor, and allows a PTFE tube coupler to screw in to the input side. You can find the coupler here: https://www.thingiverse.com/thing:2755127

This serves a couple of purposes. Primarily, it prevents wear to the filament sensor housing by guiding the path of the filament with a length of PTFE tube on the input. It also helps reduce air exposure to humidity sensitive filaments like PETG and Nylon by keeping the filament enclosed on its way from your dry box.

This object was made in Tinkercad. Edit it online https://www.tinkercad.com/things/3XxlCKJPTjA

CR10-S Filament Sensor Teflon PTFE Bowden Tube Guide

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4555321.

The crown and tubing adapter for my Somfy 530R2 CMO roller shutter motor shattered, so I needed a suitable replacement coupling to fit inside the ~46mm ID of the mating pipe.

The retaining ring is required or you risk pulling the planetary gear assembly (behind the white cog/gear shown) when removing the newly printed coupling. If your original crown is intact (the black plastic that covers the pictured white cog), this model might not be for you, unless you are OK with removing that crown. If I were in that situation, I would model one to fit around the original crown instead, leaving the OEM crown intact.

The coupling is keyed, so you can be assured it will only re-assemble in the same orientation, should you need to remove the motor again.

If you need to modify this for a different size pipe or tubing, you can find the models on Thingiverse below for your remix. There are two representations of the motor side of the coupling, which you can turn into a hole and subtract out of a simple cylinder or hexagon that fits your needs.

I printed mine solid out of PETG (all walls), and pre-drilled 4 holes through the mating pipe every 90 degrees into the coupling, and used self-tapping screws to secure it.

This object was made in Tinkercad. Edit it online https://www.tinkercad.com/things/1xQTaQE6vVk

Somfy 530R2 CMO Roller Shutter Motor Crown Coupling and Retaining Ring

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3358044.

Needed a replacement for the natural rubber plug that usually comes with or is sold for utility tubs. They usually degrade quickly because of the natural rubber that they are made with. This TPU plug ought to last much longer. Has a diameter of 42mm on top, and 36mm on the bottom. Also has a loop to attach a pull chain.

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/62YsYe491wR

Laundry Utility Sink Tub Plug

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4670763.

Simple baby proofing lock for Ikea HAVSTA cabinets. Clip down one side to one handle, then swing the other side over the other handle and push down on the top of the clip to lock (**do not push down on the clip's handle**). Press up on the outer edge of the clip (or the clip handle) to unlock.

Comes with two variants:
- One with a handle for easier unlocking by older kids
- One without a handle to make it harder for older kids to unlock it as well.

This object was made in Tinkercad. Edit it online https://www.tinkercad.com/things/gwVplU6KRiO

Ikea Havsta Cabinet Baby Proof Lock

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4336504.

I have a Ridgid R4514 Pro 10 in. Jobsite Table Saw, on which I broke the little springed sliding retaining fingers off the fence slide while removing the fence. I could probably have them replaced under the warranty or the lifetime service agreement, however I wanted my saw fixed asap, so I modeled one.

This part is labeled "V1", but the actual part number in the parts list is 089240028112 (seen here in Figure F as 12, Slider: https://ridgid.ordertree.com/media/models/docs/1031/R4514_836_r_01.pdf)

This thing was made with Tinkercad. Edit it online https://v1.tinkercad.com/things/8fzTvIszlj7

Ridgid R4514 Pro 10in. Jobsite Table Saw Fence V1 Slider (P/N 089240028112)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4689407.

Designed to compliment the Resin Vat Drip Stack Remix by DaakTwo (https://www.thingiverse.com/thing:3784926)

For the screen media, I took one of the funnel strainers that came with my Saturn, and dunked it in denatured alcohol (isopropyl alcohol may work as well). This caused the adhesive to soften and release the screen from the paper. You can then cut this rectangular screen in half, giving you two ~30mm squares of filtering media.

Hold one square of screen in place on the funnel, then snap the retaining ring down on top. This holds the screen in place quite securely.

This funnel should be reusable an indefinite number of times assuming you rinse out the resin debris after each use. I suspect this sieve would also work fairly well for filtering out larger debris in your alcohol bath.

Update 2/3/21: Added an FDM version that doesn't have the built-in resin venting arches next to the build plate.

This object was made in Tinkercad. Edit it online https://www.tinkercad.com/things/83jBCneqFAv

Resin Funnel with Screen Retainer

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4107321.

The original model by jwebst didn't work on at least the 9mm mags. The push post was too thick to allow the next round to insert sufficiently into the magazine and hold itself in place. This version trims that post down significantly and moves it back further, allowing the round to seat in place before releasing the mag loader.

Additionally, I've added an access hole at the back of the mag loader to allow a stuck round to be pushed out and ejected (should be a rare case with this modified version)

This thing was remixed with Tinkercad. Edit it online https://www.tinkercad.com/things/7ARD9vFP4Ny

S&W M&P Shield 9mm Magazine Loader Remix

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4533590.

Kudos to @mattlang and @wmealing for the inspirations: https://www.thingiverse.com/thing:782152 and https://www.thingiverse.com/thing:1696315

Decided to take the opportunity to learn some OpenSCAD and turn this into a customizer from scratch!

Practically every dimension of this is customizable, however I think most people just want to adjust the table/desk thickness, the clip tension, and the coil diameter, which are the first options. I also added a small divot for a Glue Dot to help it stay in place on a desk's top. You can easily turn this off by setting this option to "0".

Customizable Table Desk Cable Management Clip with optional Glue Dot

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4501951.

I was given a set of sliding panel shades that I repurposed as a video conference backdrop for my office space. These clips slide on to the top of the panels, and have a hole for hanging the panel from the wall or ceiling using a drywall screw. Two should be sufficient for hanging from the wall, but 3-4 may be needed for securely hanging from the ceiling.

I believe these are Graber or Springs Window Fashions brand shades, but was unable to confirm for certain. Should work with any sliding panel shade that uses the ~6mm thick aluminum extrusion shown in the photo above.

This object was made in Tinkercad. Edit it online https://www.tinkercad.com/things/1VJcScESCD7

Graber Sliding Panel Shade Hanging Brackets

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4670295.

Replacement inner door trim clips for a Nissan NV3500 (and probably other Nissan models). I made two variations, one with thicker clips, and one with thinner clips. I printed mine with the thicker clips, but realized they were a bit too difficult to push in (had to punch the door panel to get them to seat), and possibly broke some in the process. As a result, I slimmed the clips' diameter down by ~1mm to make them easier to insert. You may want to try out both before settling on which variation works better on your vehicle.

I printed mine on an Elegoo Saturn resin printer, oriented 90° sideways so that the supports contact the edge of each disk and clip and the disks print upright (see attached image).

For FDM printers, you may need to use tree supports, OR try laying the models on their side, drop the Z through the build plate, and print with the internal posts laying on the bed, cutting off ~40% of the side of the clip.

This object was made in Tinkercad. Edit it online https://www.tinkercad.com/things/6hu7bLofelG

Nissan Door Panel Trim Clips

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4322106.

This is a bracket for mounting an HC-SR04 ultrasonic distance sensor inside the salt well of a Morton MC30 water softener. This is part of a Home Assistant integration project.

This first version is minimalist. There is no cover yet designed, and the ESP module (ie, Wemos D1 Mini) has no set mounting space. There's still plenty of room for you to adhere one with foam tape. I plan to make a future version that has mounting accommodations for a D1 Mini or NodeMCU.

Sensor measurements in my tank are (+/- 0.01m):
Level 0: 0.82m
Level 1: 0.74m
Level 2: 0.66m
Level 3: 0.58m
Level 4: 0.50m
Level 5: 0.42m
Level 6: 0.34m
Level 7: 0.26m
Level 8: 0.18m

In my experience, filling from level 0 to level 8 is almost exactly 160 pounds of salt pellets (Diamond Crystal brand). Therefore each level increment equals about 20 pounds of salt or about 0.08 meters.

Example HA / ESPHome yaml coming soon!

~1 year update: Unfortunately I never got around to designing a full cover for it, and the salt eventually took its toll on the contacts between the Wemos D1 mini and the ultrasonic sensor. Next time around, I'll probably place the D1 mini inside the softener control housing, run wires from there, and cover up the circuitry of the ultrasonic sensor as best I can with silicone sealant.

This thing was made with Tinkercad. Edit it online https://v1.tinkercad.com/things/gvvtS5NGuSh

Morton MC30 Water Softener HC-SR04 Ultrasonic Salt Level Distance Sensor Bracket

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3675071.

One of my lava lamps was missing its top cap. Measured and modeled this based upon the cap on my other lamp.

I printed mine in PETG which has proven durable in the high heat of the lamp, but PLA might work as well. If you give it a shot, let me know in to comments what its durability is when printed with PLA.

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/i4fyjncxF4C

Lava Lamp Cap Replacement

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4135551.

Made for the (Medal Sports) MD Sports Pro Court, which comes in several different cosmetic variants, but most of them look something like this: https://www.medalsports.com/product/pro-court-basketball-game/

The original pins that kept the ball return folded in the upright position got lost on my set after "somebody's kids" ripped them free of the chains on the frame. Additionally, the sheet metal eventually started to bend after similar abuse. Regardless, I wanted something a bit more convenient to use than bending down and aligning two pins on the hinge.

This clip attaches to the tubing that holds the control panel, and swings down to meet and clip onto the basketball hoop when folded in the upright position. I printed with 2 walls/shells and two top/bottom layers with 20% infill in PETG, which seemed to provide sufficient durability, but YMMV. Increasing the wall count will likely increase clip rigidity if you want a more secure fit.

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/9Xaxe9r1PKA

MD Sports Pro Court Folding Hoop Latch

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3046578.

A sleeve meant to enclose the Jenga block holder/aligner device here: https://www.thingiverse.com/thing:826036

Basically a remix of https://www.thingiverse.com/thing:1952372, which had walls that were too thin and therefore not durable enough. This doubles the wall thickness from 0.8 mm to 1.6 mm.

The font used for the Jenga label is just from the basic fonts in Tinkercad. Feel free to modify if know of a better font to put on there...

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/czCiw7e7OOz

Jenga Sleeve

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4785256.

OpenSCAD remix of the Blockmit Jig for stamping a cold wallet backup on washers.

Customizer created to help people use different sized washers. Just measure the washer outer diameter and the hole inner diameter, and input that into the customizer.

To output just the base or just the indexer STLs, leave just one option set to "1" at a time, and the other "0".

Blockmit Cold Wallet Washer Stamping Jig Customizer

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3200044.

Little fingers love to push the tubular lock on my Sentry Safe, which means when I need to unlock it, I need to go searching for the physical key as well as the code. This is a simple cover for the tubular lock to prevent accidental pushes, and to reduce interest of those little fingers.

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/bbMuIKt2rW4

Sentry Safe 14mm Tubular Push Lock Cover

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3027018.

Simple bracket for mounting a garden hose or dishwasher hose using a single screw. See also the remix version of this with built-in cleats to avoid bracket rotation: 

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/bmyaPNrVBe9

Garden/Dishwasher Hose Bracket

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3701153.

The original regulator dial by rubisco2000 was great, except that my regulator's screw turns with quite a bit more resistance than most, apparently. As a result, the plastic rail that the flat-head screw slides into wasn't strong enough to hold the screw, even with the lock nut tightened into place. Therefore I needed a version of this with a hole in the face to allow me to tighten the screw down against the nut more securely.

A couple other, minor adjustments to this model:
- Reduced the size of the insertion holes to match the width of the screw head slide channel
- Removed the flat-head slot rail since it's no longer of any value

The modified SCAD document is also attached.

Kegerator Pressure Regulator Dial w/Hole

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3391381.

This is made for the Lakso 18″ Remote Control Cyclone Pedestal Fan Model 1843, however it may work with other models. I suspect it works with any 18" oscillating model.

I think this is best printed with the long shaft to the print bed so that the clean top side is reserved for the surfaces in contact with the nylon arm that connects to the pedestal body. Printing with the shaft facing up will likely require less support material, but the mating surface quality will likely suffer.

You'll need to print this with a more durable filament, such as PETG, Nylon, or ABS since it is under a decent amount of stress.

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/6CQLc1hIIRj

Lasko 18 inch Oscillating Pedestal Fan Transmission Crank Arm

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3027016.

Remix of https://www.thingiverse.com/thing:3027018, just with cleats added.

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/1ZL60oUic1b

Garden/Dishwasher Hose Bracket with Cleats

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4550382.

This is a monogrammed tag for an Anker Soundcore Life Q10 bluetooth headset. This was designed in OpenSCAD, and is uploaded as a Customizer, so you can change the monogram initials to whatever you like.

Anker Soundcore Life Q10 Monogrammed Name Tag Clip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3352079.

Needed some replacement o-rings for my eSpring water filter's faucet. Printed these with TPU.

You'll need two. Faucet tube can be pulled straight out of the valve body. Once the o-rings have been replaced, the faucet tube is pressed back in to the valve body and has a tight press fit to hold everything in place.

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/3PJ310uj7ZJ

eSpring Water Faucet O-Ring

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3675463.

Lower guide on our shower door busted. Needed a replacement. Prints on edge for increased strength.

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/c6dqjT9MNe2

Sliding Shower Door Lower Guide

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3805780.

Fits a Lifetime table model 80256. May fit others. Check your table clip measurements against the model in Tinkercad before printing.

Designed to be beefier than the original for durability. Print in something like PETG or ABS. PLA likely would warp and lose clamping power over time.

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/8C1cPS5XjGm

Leg Clip for Lifetime 80256 4 Foot Adjustable Height Table

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4556486.

Simple replacement for a split-shaft knurled rotary switch, like those found on halogen torchiere lamps.

This object was made in Tinkercad. Edit it online https://www.tinkercad.com/things/eb2W6cgKXTx

Halogen Torchiere Rotary Switch Knob

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3717326.

Designed to snap onto the base of the newer style brush heads (such as those with the RFID/wireless chip built in). Print with 0.4 nozzle for proper clearances. Should easily snap onto the base and remain attached. If too tight, or too loose, adjust the X/Y scaling in your slicer by a small percentage (~1-5%)

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/gJbKPrud7pP

Sonicare Brush Head Color Ring

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

muchtall