Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3512468.

For a OnePlus 6 with the Orzly Fusion Bumper case. 

Affiliate link: https://amzn.to/2XcEG0H

non-Affiliate link: https://smile.amazon.com/Orzly-OnePlus-SmartPhone-Protective-Absorbing/dp/B07D4MDMD1/

**Make sure you use PETG or ABS or another higher temperature plastic as PLA will just warp and melt if left in the sun.**

This is a phone holder I designed to go on the Proclip USA swivel in my car.  It is a semi work in progress, I have not printed it myself yet but will be in the next few days.  

Holes for screws are 30mm x 38mm to mount to a swivel.  The Rear camera will work.  

I am using this in combination with a dash mount I designed for a Miata at autocross events to for data logging using Solostorm.

** update 21-5-2019 **
- Fixed sizing of the holder.  
- Reduced the catch lip, it was a bit much and overstressing the print when trying to remove the phone from it.
- Added version with the mounting holes in the center. 

** Update 22-5-2019 **
- Adjusted sizing to better hold the phone, it was a little loose on the latest test print.

** Update 23-5-2019 **
- Adjusted sizing one last time and fixed the camera hole not being centered. my print of this turned out great and fit great.

OnePlus 6 Orzly Case phone mount.

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2802524.

This is a friction fit tracker mount for putting an HTC Vive Tracker on a Logitech C920, C922 or C930e webcam. It will allow for the full tilt of the webcam on its base.

Logitech C920
https://www.amazon.com/gp/product/B006JH8T3S/ref=as_li_ss_tl?ie=UTF8&linkCode=sl1&tag=mtgeekman06-20&linkId=46b4652483134e26d7f8fc1963e278c5&language=en_US

Logitech C922x 
https://www.amazon.com/gp/product/B006JH8T3S/ref=as_li_ss_tl?ie=UTF8&linkCode=sl1&tag=mtgeekman06-20&linkId=46b4652483134e26d7f8fc1963e278c5&language=en_US

Logitech C930e
https://www.amazon.com/gp/product/B006JH8T3S/ref=as_li_ss_tl?ie=UTF8&linkCode=sl1&tag=mtgeekman06-20&linkId=46b4652483134e26d7f8fc1963e278c5&language=en_US


Vive Tracker
https://www.amazon.com/gp/product/B006JH8T3S/ref=as_li_ss_tl?ie=UTF8&linkCode=sl1&tag=mtgeekman06-20&linkId=46b4652483134e26d7f8fc1963e278c5&language=en_US

The mount holds on pretty tight by itself, but you can always add a little bit of double-sided tape to the top of your webcam to add that little bit of extra grip.  

You will need a 1/2 inch 1/4x20 bolt or screw to attach the Vive tracker to the mount.  This is a standard camera mount thread.

23-8-2018  Added an untested version of the mount with a nut slot to keep the screw in place and cut holes for the microphones built into the camera.  If you print this version please let me know of any problems with it.  I do not have a way to test for quite some time.




Logitech C920 / 922 / 930e Vive Tracker Mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2959822.

For a OnePlus 6 with the Otterbox Commuter case. 

Affiliate link: https://amzn.to/2FB4w3G

non-affiliate link: https://smile.amazon.com/OtterBox-Commuter-Cell-Phone-OnePlus/dp/B07DW85TFD

This is a phone holder I designed to go on the Proclip USA swivel in my car.  It is a semi work in progress, I have not printed it myself yet but will be in the next few days.  

Holes for screws are 30mm x 38mm to mount to a swivel.  The Rear camera will work.  

I am using this in combination with a dash mount I designed for a Miata at autocross events to for data logging using solostorm.


*** Updated 06-15-2018
Adjusted size, the first print came out too large and the phone flopped around.  Also adjusted camera hole for better alignment.

*** Updated 03-23-2019
Adjusted size again, as it was a little narrow and I ended up breaking one of the holding in tabs.

OnePlus 6 Otterbox Commuter dash holder.

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2378629.

This is a custom Phone Holder for my OnePlus 3 in the OtterBox case from OnePlus.  It is a little overbuilt for just holding a phone but the end goal is to use this mount in my Miata for Autocross event data logging.

Hole Pattern matches the mounts from ProClip USA as I already had some mounts from them.  

OnePlus 3/3T phone Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2389361.

This is a dash mount for a gen 1 (2000-2006) Honda Insight, it fits into the left center air vent above the stereo.  The holes match up to a ProClip USA mount.

I have printed it in PLA for testing and PETG for a final print to be able to stand the temperatures and the sun better. 

I HIGHLY recommend using PETG or ABS as a minimum.  PLA will warp in the sun.

Gen 1 Honda Insight Dash Mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2960222.

**I highly recommend you print this in ABS.  On my black dash in the sun, it gets hot enough that PETG starts to sag and warp.**  

This is a dash mount I designed to go with a phone holder I designed for Autocross events.
 
Holes are patterned for a ProClip ball mount. 

I have attached it to the dash using some of the 30lb Double-sided 3M tape to make sure it will not go anywhere. 

link: https://smile.amazon.com/3M-Scotch-Extreme-Mounting-60-Inch/dp/B005SRECEU/

I have uploaded the latest version, This one has been in my car for 4 or 5 months now with no issues.  The fit is good and I have been using it to mount my OnePlus 6 phone on the dash at Autocross events and just everyday driving.


NB Miata Dash Mount

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow