This model aims to replace the tank base silicon “portioner” for the Petlibro Granary (PLAF005) with a smaller opening. This reduces the amount of kibbles dispensed which is especially useful when using smaller kibbles.

PetLibro Granary Small Kibble Adapter

Petlibro+Wheel+STL.stl

Commercial rights to **sell prints** of all Moss Pole **Starter Kits**


The **Starter Kits** are available in the following versions:
- [Petit (70mm)](https://thangs.com/designer/mochpoch/3d-model/Moss%20Pole%20-%20Starter%20Kit%20%2870mm%29-1126210)
- [Original (118mm)](https://thangs.com/designer/mochpoch/3d-model/Moss%20Pole%20-%20Starter%20Kit%20%28118mm%29-1126202)


On this plan, a **Starter Kit** includes:
  - Backing 
      ✔ 200mm
      ✘ 145mm
      ✘ 100mm

  - Grid
      ✔ Hex (when design is available)
      ✘ Strip (when design is available)
      ✘ Diamond (when design is available)

  - Base
      ✔ Basic
      ✔ Round-end
      ✔ Inserts (to catch pole medium)
      ✘ Tapered

  - Drip Watering Topper
      ✔ 150ml
      ✘ 300ml

  - Wick Holder Cap
      ✔ for 10mm wick
      ✘ for 12mm wick (when compatible)

  - Stake Clip
      ✘ 8mm
      ✘ 11mm
      ✘ 16mm

_Note:_
  ✘ Not included in the kit
  ✔ Included in the kit

The license for selling prints of models in this plan is only valid with an active membership. Be sure to review the license agreement before purchasing your membership.↓

Starter

Commercial rights to **sell prints** of all Moss Pole **Grower Kits**

The **Grower Kits** are available in the following versions:
- [Petit (70mm)](https://thangs.com/designer/mochpoch/3d-model/Moss%20Pole%20-%20Grower%20Kit%20%2870mm%29-1126208)
- [Original (118mm)](https://thangs.com/designer/mochpoch/3d-model/Moss%20Pole%20-%20Grower%20Kit%20%28118mm%29-1126205)


On this plan, a **Grower Kit** includes: 
   - Backing 
       ✔ 200mm
       ✔ 145mm
       ✔ 100mm

   - Grid
       ✔ Hex (when design is available)
       ✔ Strip (when design is available)
       ✔ Diamond (when design is available)

   - Base
       ✔ Basic
       ✔ Round-end
       ✔ Inserts (to catch pole medium)
       ✔ Tapered

   - Drip Watering Topper
       ✔ 150ml
       ✔ 300ml

   - Wick Holder Cap
       ✔ for 10mm wick
       ✔ for 12mm wick (when compatible)

   - Stake Clip
       ✔ 8mm
       ✔ 11mm
       ✔ 16mm

_Note:_
  ✘ Not included in the kit
  ✔ Included in the kit

The license for selling prints of models in this plan is only valid with an active membership. Be sure to review the license agreement before purchasing your membership.↓

Grower

Whether you&#39;re new to plants or upgrading your setup, this **Starter Kit (118mm)** extends your pot, promoting root growth and helping your plants mature with larger, healthier leaves.

This kit includes **select** models of the **Moss Pole (118mm)** as seen in [Printables](https://www.printables.com/model/810356-moss-pole) and [MakerWorld](https://makerworld.com/en/models/440452).

**Inclusions**

*   Backing
    
    *   1x 200mm backing
        
*   Grid
    
    *   1x medium hex grid
        
*   Base
    
    *   1x basic base
        
    *   2x round-end base
        
    *   1x compatible base insert
        
*   Drip-watering topper
    
    *   1x single hole, 150ml drip watering cap
        
    *   1x double hole, 150ml drip watering cap
        
    *   1x triple hole, 150ml drip watering cap
        
*   Wick-holder cap
    
    *   1x wick holder cap for wick diameter ≤10mm wick diameter
        

**Printing Guidelines**

_General_

*   PETG is the recommended filament type.
    
*   Bed adhesion is key to a successful print, and using a brim on certain parts can help with this. Some printers allow you to reduce the speed after the print has started, which can be easier than adjusting the speed for different layers. However, this still depends on the type of filament you&#39;re using.
    
*   Although not required, applying a sealant to any modules that will be in contact with water can help extend their lifespan.
    

_Backing_

1.  Place top-side down without supports, ensuring the connection flap is at the top. (For reinforced strength on the flap, print at a 45° angle.)
    
2.  Set the outer brim to a width of 20 mm. (A brim-object gap of 0.13 mm may be used to minimize the need for deburring, but it could reduce bed adhesion.)
    

_Grid_

1.  Set flat on the bed without brim or supports.
    
2.  Set the desired top layer pattern; ironing is not required.
    

_Base_ _/ Leg_

1.  Place flat-side down without supports.
    
2.  Set the outer brim to a width of 20 mm. (A brim-object gap of 0.13 mm may be used to minimize the need for deburring, but it could reduce bed adhesion.)
    

_Drip-Watering Topper_

1.  Place the topper with the drip-hole facing the bed.
    
2.  Set wall loops to 3.
    
3.  Set top shell layers to 3.
    
4.  Set bottom shell layers to 5.
    
5.  Enable tree support (organic).
    
    1.  Set support branch angle to 45°.
        
    2.  Set top Z distance to 0.25 mm.
        
    3.  Set base pattern to hollow.
        
    4.  Set top interface layers to 3.
        
    5.  Set top interface spacing to 0.7 mm.
        

**Modularity**

Get creative with different module combinations to build your own unique vertical extension. While this project is still evolving, future updates will always keep parts compatible—and your feedback is always welcome.

Happy growing!

Moss Pole - Starter Kit (118mm)

backing-200mm.stl

base-open-round-end-120mmh.stl

base-round-120mmh-insert.stl

base-sealed-round-end-120mmh.stl

base-basic-open.stl

grid-hex-medium-200mm.stl

topper-watering-cap-triple-hole-150ml.stl

topper-watering-cap-single-hole-150ml.stl

topper-watering-cap-double-hole-150ml.stl

wick-holder-cap-10mmdiameter.stl

Whether you&#39;re new to plants or upgrading your setup, this **Grower Kit (118mm)** extends your pot, promoting root growth and helping your plants mature with larger, healthier leaves.

This kit includes models of the **Moss Pole (118mm)** as seen in [Printables](https://www.printables.com/model/810356-moss-pole) and [MakerWorld](https://makerworld.com/en/models/440452).

**Inclusions**

*   Backing
    
    *   1x 200mm backing
        
    *   1x 145mm backing
        
    *   1x 100mm backing
        
*   Grid
    
    *   1x medium hex 200mm grid
        
    *   1x medium hex 145mm grid
        
    *   1x medium hex 100mm grid
        
    *   1x small diamond 200mm grid
        
    *   1x medium diamond 200mm grid
        
    *   1x large diamond 200mm grid
        
    *   1x medium strip 200mm grid
        
    *   1x medium strip 100mm grid
        
*   Base
    
    *   1x basic base
        
    *   1x round-end base
        
    *   1x compatible base insert
        
    *   2x tapered base
        
*   Drip-watering topper
    
    *   1x single hole, 150ml drip watering cap
        
    *   1x double hole, 150ml drip watering cap
        
    *   1x triple hole, 150ml drip watering cap
        
    *   1x single hole, 300ml drip watering cap
        
    *   1x double hole, 300ml drip watering cap
        
    *   1x triple hole, 300ml drip watering cap
        
*   Wick-holder cap
    
    *   1x wick holder cap for wick diameter ≤10mm wick diameter
        
    *   1x wick holder cap for wick diameter ≤12mm wick diameter
        
*   Stake-clip
    
    *   1x &nbsp;clip for 8 to 9.5 mm stake diameter
        
    *   1x  clip for 11 to 13 mm  stake diameter
        
    *   1x  clip for 16 to 19.5 mm  stake diameter
        

**Printing Guidelines**

_General_

*   PETG is the recommended filament type.
    
*   Bed adhesion is key to a successful print, and using a brim on certain parts can help with this. Some printers allow you to reduce the speed after the print has started, which can be easier than adjusting the speed for different layers. However, this still depends on the type of filament you&#39;re using.
    
*   Although not required, applying a sealant to any modules that will be in contact with water can help extend their lifespan.
    

_Backing_

1.  Place top-side down without supports, ensuring the connection flap is at the top. (For reinforced strength on the flap, print at a 45° angle.)
    
2.  Set the outer brim to a width of 20 mm. (A brim-object gap of 0.13 mm may be used to minimize the need for deburring, but it could reduce bed adhesion.)
    

_Grid_

1.  Place flat on the bed without brim or supports.
    
2.  Set the desired top layer pattern; ironing is not required.
    

_Base_ _/ Leg_

1.  Place flat-side down without supports.
    
2.  Set the outer brim to a width of 20 mm. (A brim-object gap of 0.13 mm may be used to minimize the need for deburring, but it could reduce bed adhesion.)
    

_Drip-Watering Topper_

1.  Place the topper with the drip-hole facing the bed.
    
2.  Set wall loops to 3.
    
3.  Set top shell layers to 3.
    
4.  Set bottom shell layers to 5.
    
5.  Enable tree support (organic).
    
    1.  Set support branch angle to 45°.
        
    2.  Set top Z distance to 0.25 mm.
        
    3.  Set base pattern to hollow.
        
    4.  Set top interface layers to 3.
        
    5.  Set top interface spacing to 0.7 mm.
        

_Stake Clip_

1.  Place the flat side on the bed without supports or brim.
    
2.  Adjust the wall loops and infill based on the strength required for the chosen filament.
    

**Modularity**

Get creative with different module combinations to build your own unique vertical extension. While this project is still evolving, future updates will always keep parts compatible—and your feedback is always welcome.

Happy growing!

Moss Pole - Grower Kit (118mm)

backing-100mm.stl

backing-145mm.stl

stake-clip-08mm.stl

stake-clip-11mm.stl

stake-clip-16mm.stl

base-tapered-120.stl

base-tapered-100.stl

grid-diamond-medium-200mm.stl

grid-diamond-small-200mm.stl.stl

grid-diamond-large-200mm.stl.stl

grid-strip-medium-200mm.stl

grid-strip-medium-100mm.stl

grid-hex-medium-100mm.stl

grid-hex-medium-145mm.stl

topper-watering-cap-triple-hole-300ml.stl

topper-watering-cap-single-hole-300ml.stl

topper-watering-cap-double-hole-300ml.stl

wick-holder-cap-12mmdiameter.stl

Whether you&#39;re new to plants or upgrading your setup, this **Grower Kit (70mm)** extends your pot, promoting root growth and helping your plants mature with larger, healthier leaves.

This kit includes **select** models of the **Moss Pole Petit (70mm)** as seen in [Printables](https://www.printables.com/model/946039-moss-pole-petit-70mm) and [MakerWorld](https://makerworld.com/en/models/558019).

**Inclusions**

*   Backing
    
    *   1x 200mm backing
        
    *   1x 145mm backing
        
    *   1x 100mm backing
        
*   Grid
    
    *   1x large hex 100mm grid
        
    *   1x large hex 200mm grid
        
    *   1x medium hex 145mm grid
        
    *   1x medium hex 200mm grid
        
    *   1x small hex 100mm grid
        
    *   2x small hex 200mm grid
        
    *   1x small diamond 200mm grid
        
    *   1x small diamond 100mm grid
        
    *   1x medium diamond 200mm grid
        
    *   1x small diamond 100mm grid
        
    *   1x medium strip 200mm grid
        
    *   1x medium strip 100mm grid
        
    *   1x small strip 200mm grid
        
    *   1x small strip 100mm grid
        
*   Base
    
    *   2x basic base
        
    *   2x round-end base
        
    *   2x skirt-end base
        
    *   2x compatible base insert
        
    *   2x tapered base
        
    *   1x tapered base insert
        
*   Drip-watering topper
    
    *   1x single hole, 150ml drip watering cap
        
    *   1x double hole, 150ml drip watering cap
        
    *   1x single hole, 300ml drip watering cap
        
    *   1x double hole, 300ml drip watering cap
        
*   Wick-holder cap
    
    *   1x wick holder cap for wick diameter ≤10mm wick diameter
        
*   Stake-clip
    
    *   1x &nbsp;clip for 8 to 9.5 mm stake diameter
        
    *   1x  clip for 11 to 13 mm  stake diameter
        
    *   1x  clip for 16 to 19.5 mm  stake diameter
        

**Printing Guidelines**

_General_

*   PETG is the recommended filament type.
    
*   Bed adhesion is key to a successful print, and using a brim on certain parts can help with this. Some printers allow you to reduce the speed after the print has started, which can be easier than adjusting the speed for different layers. However, this still depends on the type of filament you&#39;re using.
    
*   Although not required, applying a sealant to any modules that will be in contact with water can help extend their lifespan.
    

_Backing_

1.  Place top-side down without supports, ensuring the connection flap is at the top. (For reinforced strength on the flap, print at a 45° angle.)
    
2.  Set the outer brim to a width of 20 mm. (A brim-object gap of 0.13 mm may be used to minimize the need for deburring, but it could reduce bed adhesion.)
    

_Grid_

1.  Set flat on the bed without brim or supports.
    
2.  Set the desired top layer pattern; ironing is not required.
    

_Base_ _/ Leg_

1.  Place flat-side down without supports.
    
2.  Set the outer brim to a width of 20 mm. (A brim-object gap of 0.13 mm may be used to minimize the need for deburring, but it could reduce bed adhesion.)
    

_Drip-Watering Topper_

1.  Place the topper with the drip-hole facing the bed.
    
2.  Set wall loops to 3.
    
3.  Set top shell layers to 3.
    
4.  Set bottom shell layers to 5.
    
5.  Enable tree support (organic).
    
    1.  Set support branch angle to 45°.
        
    2.  Set top Z distance to 0.25 mm.
        
    3.  Set base pattern to hollow.
        
    4.  Set top interface layers to 3.
        
    5.  Set top interface spacing to 0.7 mm.
        

_Stake Clip_

1.  Place the flat side on the bed without supports or brim.
    
2.  Adjust the wall loops and infill based on the strength required for the chosen filament.
    

**Modularity**

Get creative with different module combinations to build your own unique vertical extension. While this project is still evolving, future updates will always keep parts compatible—and your feedback is always welcome.

Happy growing!

Moss Pole - Grower Kit (70mm)

base-basic-open-bottom.stl

base-tapered-160mm.stl

base-tapered-160mm-insert.stl

base-tapered-100mm.stl

grid-diamond-medium-100mm.stl

grid-diamond-small-200mm.stl

grid-diamond-small-100mm.stl

grid-strip-small-100mm.stl

grid-strip-small-200mm.stl

grid-hex-small-100mm-type1.stl

grid-hex-small-200mm-type1.stl

grid-hex-large-100mm.stl

grid-hex-small-200mm-type2.stl

grid-hex-large-200mm.stl

base-round-125mmh-insert.stl

base-round-125mmh-60mmd.stl

base-skirt-125mmh-100mmd.stl

base-round-100mmh-60mmd.stl

base-skirt-100mmh-100mmd.stl

base-round-100mmh-insert.stl

Whether you&#39;re new to plants or upgrading your setup, this **Starter Kit (70mm)** extends your pot, promoting root growth and helping your plants mature with larger, healthier leaves.

This kit includes **select** models of the **Moss Pole Petit (70mm)** as seen in [Printables](https://www.printables.com/model/946039-moss-pole-petit-70mm) and [MakerWorld](https://makerworld.com/en/models/558019).

**Inclusions**

*   Backing
    
    *   1x 200mm backing
        
*   Grid
    
    *   1x large hex grid
        
    *   1x medium hex grid
        
    *   2x small hex grid
        
*   Base
    
    *   2x basic base
        
    *   2x round-end base
        
    *   2x skirt-end base
        
    *   2x compatible base insert
        
*   Drip-watering topper
    
    *   1x single hole, 150ml drip watering cap
        
    *   1x double hole, 150ml drip watering cap
        
*   Wick-holder cap
    
    *   1x wick holder cap for wick diameter ≤10mm wick diameter
        

**Printing Guidelines**

_General_

*   PETG is the recommended filament type.
    
*   Bed adhesion is key to a successful print, and using a brim on certain parts can help with this. Some printers allow you to reduce the speed after the print has started, which can be easier than adjusting the speed for different layers. However, this still depends on the type of filament you&#39;re using.
    
*   Although not required, applying a sealant to any modules that will be in contact with water can help extend their lifespan.
    

_Backing_

1.  Place top-side down without supports, ensuring the connection flap is at the top. (For reinforced strength on the flap, print at a 45° angle.)
    
2.  Set the outer brim to a width of 20 mm. (A brim-object gap of 0.13 mm may be used to minimize the need for deburring, but it could reduce bed adhesion.)
    

_Grid_

1.  Set flat on the bed without brim or supports.
    
2.  Set the desired top layer pattern; ironing is not required.
    

_Base_ _/ Leg_

1.  Place flat-side down without supports.
    
2.  Set the outer brim to a width of 20 mm. (A brim-object gap of 0.13 mm may be used to minimize the need for deburring, but it could reduce bed adhesion.)
    

_Drip-Watering Topper_

1.  Place the topper with the drip-hole facing the bed.
    
2.  Set wall loops to 3.
    
3.  Set top shell layers to 3.
    
4.  Set bottom shell layers to 5.
    
5.  Enable tree support (organic).
    
    1.  Set support branch angle to 45°.
        
    2.  Set top Z distance to 0.25 mm.
        
    3.  Set base pattern to hollow.
        
    4.  Set top interface layers to 3.
        
    5.  Set top interface spacing to 0.7 mm.
        

**Modularity**

Get creative with different module combinations to build your own unique vertical extension. While this project is still evolving, future updates will always keep parts compatible—and your feedback is always welcome.

Happy growing!

Moss Pole - Starter Kit (70mm)

an engineer 3D designing for Mochi🐾 & the houseplants 🌿

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

mochpoch

Achievements

Seedling

Pinned models

Moss Pole - Starter Kit (118mm)

Moss Pole - Grower Kit (118mm)

Moss Pole - Grower Kit (70mm)

Moss Pole - Starter Kit (70mm)

PetLibro Granary Small Kibble Adapter