I wanted a Vesa mount that would sit my 27" monitor as close to the wall as possible and could not find any at the store. I also had some holes on the wall from the previous one so I decided to design one that would fit my requirements.

For interfacing the two parts I used M5 bolts and hex nuts that I had laying around from spools of ESun ABS+ but you can probably get them from your local hardware store.

I printed it with ABS+, 4 walls and 35% gyroid infill, but this might be overkill. It feels so solid that I wouldn't be amazed if it can hold a 65" TV

Super slim vesa 100 monitor wall mount

Wall mountV2.stl

Chack holder

Bottom.stl

My antenna cover broke from the base, so I designed this to go over the antenna wire. It is held into place with some glue or some bluetack



Arrma_antenna_holder_v1.stl

The holder for my Arrma Voltage ESC broke off. I used some double sided to hold it down but it got dirty and loose over time, so I instead designed a thin base with beefier holder to screw down using the original holes. I have glued the bottom of the ESC to the top of this part and it feels really solid now, but can also be easily removed by unscrewing it.



ESC_base_v3.stl

Created a headphone stand to either wall mount or interface with a base to fit my desk (with the option to make more bases).

The base interfaces with a M3 nut and a 6mm screw allowing for a 8.5mm thick desk (glass).

Headphone holder

headphone_stand.stl

This is the rear camber link for the Arrma Voltage RC truck. Lost the steering link and designed that here: https://thangs.com/masimplo/Arrma-Voltage-steering-link-16901 so I created this one as well just in case.



Arrma_voltage_rear_camber_link_v1.stl

This is the steering link for the Arrma Voltage RC truck. Lost mine on a crash and lead time was months to get a new one, so I designed it using the other one as reference.

V1 is a loose fit (use if you have not calibrated your printer)
V2 is a tighter fit

Arrma Voltage steering link

Arrma_steering_link_v2.stl

Like the original design that is available here: https://www.thingiverse.com/thing:1219107 but I wanted to attach mine to the wall as 4 toothbrushes take a lot of space, so I added a small wall that I intent to glue to the wall with some montage glue or strong two sided tape (did not want to drill holes to the tiles)



toothbrushholder-4-wall.stl

I needed a place for the tools I am using for my 3d prints and thought of making a custom rack that would fit everything I use, but I think it is pretty versatile to hold different small tools. I got mine mounted onto my lack printer enclosure.

Print settings:
- Needs supports

pliers_rack.stl

I needed a place for the tools I am using for my 3d prints and thought of making a custom rack that would fit everything I use, but I think it is pretty versatile to hold different small tools. I got mine mounted onto my lack printer enclosure.

I measured the caps on my Astra 18" wheels and they are much longer than other available designs, 320mm long and 17mm wide.

Printing these on the side instead of the more "reasonable" upright will give the part strength for when pulling out of the wheel nut, otherwise it might split unless you print them with nylon or something with great layer adhesion.

Astra_wheel_nut_cap_v1.stl

A chalk holder to attach to a black board



chalk_holder_v4.stl

Sunglasses holder to fasten to wall with some double sided tape

glasses holder v2.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow