The rifled bottom of the Cafelat Robot doesn't work well with scales. This pad is intended to fix that issue by providing a flat and steady surface for scales.

Cafelat Robot Scales Pad 

scales pad.stl

Yet another filament dust filter here. The best one, if you ask me!

- Simple snap-fit design
- No screws or other fasteners needed, only the printed parts (and a piece of sponge)
- Can be hot-mounted onto a filament without fully reloading it (i.e. you could snap it onto a filament at any place; you don't need to thread the filament's open end through it)
- Fully parameterizable design with a FreeCAD source attached

Useful? Consider [supporting me](https://github.com/sponsors/madhead) on GitHub 🤑.

 Filament / Dust Filter

Filament Filter Half 2.stl

Simple cable strain relief for the Micro Swiss Direct Drive (Ender 5 version). Prints with no supports. Mounts on the aluminum plate with a screw. FreeCAD file included, so you could easily adapt it for your needs.

If you enjoyed this thing, consider [supporting me](https://github.com/sponsors/madhead) on GitHub 🤑.

Ender 5 Micro Swiss Direct Drive Cable Strain Relief

Parameterizable (using FreeCAD) plinth clips.

Parameterizable plinth clamps

A little piece to move the pressure gauge to the head of your Robot. No gauge disassembly needed!

The attached STL is for a 8 mm screw with 12 mm head, although the FreeCAD source would allow easy modifications. Some Robots are known to use smaller screws. For instance, the original model was designed for a 6 mm screw.

Cafelat Robot Pressure Gauge Mount

A simple 20 mm calibration without the "Z" on its top. Instead, it says "N", which stands for a ["Normal"](https://en.wikipedia.org/wiki/Normal_(geometry)).

There is also a FreeCAD source attached, so you could easily resize or tune the thing using the [original guide](https://www.idig3dprinting.co.uk/news/how-to-guides/create-a-3d-printer-calibration-cube-in-freecad).

Calibration Cube, 20 mm

calibration cube (chamfer).stl

The container that comes with the brewer constantly pops open. So, I've made a more secure one to let you Go and brew you cup wherever your adventures take you.

AeroPress filters container 

base.stl

A replacement for the standard knob with improved grip.

Ender 5 kurled knob 

Make the most out of your dish soap with this fantastic upside down bottle holder.

Dish soap bottle holder 

Dedica Portafilter Funnel: embodying a minimalistic design, simplicity, and an absence of hanging components.

The accompanying FreeCAD model allows for effortless customization of the print, adapting to a diverse range of espresso machines. Whether your machine's portafilter measures 51, 54, 58 mm or exceeds these dimensions, and whether it possesses 2 or 3 ears, this model can be seamlessly adjusted to suit your requirements.

DēLonghi Dedica portafilter funnel × 51 mm

funnel

It's very easy to scratch the spine of your chair if you sit close to a wall. Or the wall.

This cap potentially protects both (if printed with a flexible resin) or the chair (if printed with a hard plastic).

JÄRVFJÄLLET office chair spine protection cap

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4316916.

Kite aerial photography picavet rig for YI 4K+

Kite aerial photography picavet rig for YI 4K+

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3490547.

Besides the printed parts you'll need:

 - [AstroSolar® Safety Film OD 5.0](https://www.baader-planetarium.com/en/solar-observation/astrosolar-safety-film-od-5.0-(20x29-100x50-117x117-cm).html) or it's alternative.
 - 58 mm screw-thread lens mount. I took my from a cheap replica of [Mennon DV-S 58](http://www.mennon-usa.com/products/mennon-dv-s-58-screw-mount-58mm-digital-video-camcorder-lens-hood-with-cap-black.html).
 - Three 4×6 mm bolts (or similar) with nuts.
 - Cyanoacrylate glue ("Super Glue").

Print the parts with a heat-resistant white plastic tolerant to UV light and sandpaper them. Cut the bolting holes to fit your bolts. Cut a ø 70 mm circle (60 mm  + 5 mm overlap) of the AstroSolar® Safety Film OD 5.0. Glue the film and one of the circle flange parts. Then glue the second flange part to the first so that the film is between two flanges. Cut the screw-threading part of the lens hood and sandpaper it too. Glue it to the triangle flange mount. Use bolts to connect the filter and the lens adapter together.

58mm solar filter for DSLR

cap.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

madhead

Achievements

Seedling

Pinned models

AeroPress filters container

Cafelat Robot Scales Pad

Filament / Dust Filter

Ender 5 Micro Swiss Direct Drive Cable Strain Relief

Parameterizable plinth clamps

Cafelat Robot Pressure Gauge Mount

Calibration Cube, 20 mm

AeroPress filters container

Ender 5 kurled knob

Dish soap bottle holder

DēLonghi Dedica portafilter funnel × 51 mm

JÄRVFJÄLLET office chair spine protection cap

Kite aerial photography picavet rig for YI 4K+

58mm solar filter for DSLR