Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5023855.

A very small Aerogarden with a removable water bowl and grow deck.

STEP and f3d files are included if you wanted to modify it

Can be printed with both Resin and Plastic.

See print settings and post printing for instructions.

1/10 Scale Miniature Aerogarden Harvest (With Removable Water Bowl)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4851462.

A Miniature Laptop insert for the Hinged Mini Pelican Case.

Files for the normal sized case are labeled "PelicanCase_v3".
Files for the mini sized case are labeled "PelicanCase-mini_v3".
The keys are used for the both of them.

The Bezel and Main body should pressure fit into the pelican case but the keys and touchpad needs to be glued into their slots. 

The display can fit a 26x33mm picture for the normal version and a 22x33mm picture for the smaller version but I just used blue pieces of paper. You can also optionally make a 10mm wide strip of paper or thin plastic and slide it into the gaps in the bezel and main body to make a fake display cable.

Refer to the attached images for assembly and STEP files are also available if you want to adjust the fit or modify it. 

Keyboard is from www.thingiverse.com/thing:3696285.

Miniature Laptop insert for Hinged Mini Pelican Case 2.0

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4976292.

A very small pc with internal components. 

The .STEP file is included if you want to create your own components for it. 

Print with resin for best results.

The side panel is optional and can be printed with clear resin

You can get a miniature display and peripherals here:
https://www.thingiverse.com/thing:4326864

Inspired by: https://www.thingiverse.com/thing:3344995


1/10 Scale Miniature PC (With Internal Components)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4343255.

Update4; Added step file
Update3: new f360 file for new version.
Update2: Uploaded new version. Better reloading.
Update: Print on side with text facing up. Needs no supports

A simple toothpick launcher designed in fusion 360

It launches toothpicks.
I say one of the king of random's old videos and saw a matchstick gun made out of a cloth-pin. I tried to make some but the results were inconsistent because of my crappy wood working skills so i decided to design 3d print my own. The result was a print that prints in less than 50 minutes and required no post-processing. Just slide a spring from a cloth-pin in and pull the pin pack into the notch and its ready. Just press the spring to shoot. The toothpicks i used were 2 mm in diameter It should work with smaller ones but i'm not sure. I have included the .f360 files if anybody wanted to modify it. 

Warning: This toy is very powerful! it can punch holes in light cardboard! Wear safety glassed when firing and do not point at other people! I am not responsible for any damaged humans and/or other objects.

Toothpick launcher

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4879907.

Miniature PC that I designed for fun. 

Should be around 1/10th scale

I have not printed this yet but I will print it soon and update this page with more photos.

I might also design a new version with a monitor, keyboard, swappable hardware, and a working side panel soon but that will probably take a while. (sneak peek: ibb.co/Yt6GK6v )

f3d and step files are included if you want to modify it.


Miniature PC

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4873533.

A bulb duster that is designed to be printed in TPU and PLA. 

Print "bulb" with flat side down and "tip" pointing up.

Superglue the tip in place if it falls out.

I have also included the f3d and step files if you want to modify it.

https://youtu.be/4dqioDClVhs



Fully Printable TPU Bulb Duster

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4942079.

A mold to make 1/10 scale cinderblocks with. Can be used with Plaster of Paris or Quick repair concrete. The PLA version is single use but the TPU version could in theory be used many times but I have not tested it yet. Instructions for the PLA version is below.



1/10 Scale Miniature Cinderblock Mold

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4229459.

Calibration cube with a city on the inside. There is a lot of fine details to test your printer. Mine just looked like some spikes in a cube. 

a normal XYZ 20mm calibration cube but with a city on the inside

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4671744.

A crashed Star destroyer.

Crashed Imperial Star Destroyer Diorama

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4303663.

A template for adding a fan onto the official pi 4 case.

I really liked how the pi 4 official case snapped together with a satisfying snap but was disappointed that there was no easy way to add a fan to cool the hot pi. I remixed another design by minorcoma that let you drill holes into the cover but i wanted a full cutout for a 40mm fan. It snaps onto your top cover and lets you drill holes and remove the cover. See post printing for details. I just used the screws that came with the fan which I think are m3 screws. Takes just under 1 1/2 hours to print. I might make a version for a 30mm fan if people want me to.

Official pi 4 case fan mod template

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4302042.

A simple holder that holds your pi. 
Needs 4 m2.5 or m2 screws to hold the pi to it. 
Should work with Pi 3 or 3+ because it has the same mounting holes. 
I've only tested it with the pi 4b because I only have that pi. 
See print settings if you want the triangle pattern on the bottom. 
I put some rubber feet on mine to make it less slippery. 
If this does not work with pi 3 or 3+ please tell me so I can improve the design.


Simple Pi 3/3+/4 compact holder/base

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

jq910

Achievements

Seedling

Debutant