**Description**
-----------

A 3x5 gridfinity tray to hold an iFixit Mahi driver kit, open, with the lid on the bottom.  

![Picture of the print](photo.jpg)

**Additional Requirements**
-----------------------

[Mahi Driver Kit from iFixit](https://www.ifixit.com/products/mahi-driver-kit-48-bit-driver-kit)

**Printing Considerations**
-----------------------

Printed with a 0.6mm nozzle in ABS with lightning infill.

No real need for that diameter or material, print however you're comfortable.

**Credits**
-------

[Gridfinity by Zack Freedman](https://gridfinity.xyz/)
[Gridfinity templates by KptnAutismus](https://github.com/KptnAutismus/KptnAutismus)

iFixit Mahi case holder

**Description**
-----------

A large column for holding my VR headset via a random skull I found at Ross. Its printed in 4 parts and designed for a 350x350 Voron - and won't fit on smaller without tweaking the design/printing in pieces.

Its also designed to simply stack vertically, optionally with gluing the lid base to the lid for greater rigidity. The base is hollow for filling with sand, to help keep the column from printing. Additionally the center column is empty, and could be used for storage (or running the cord inside if you wanted to put a hole in the back of the column)

If you wish to change the height of the column - just adjust the body piece in fusion360 - it will recalculate the flutes to still look nice.

Finally, on the backside of the lid, there are spots for M3 heat set inserts. This is to allow for flexability in designing cable management, if needed. Just use whatever anchor points you need, and design whatever you like to fit.

![Picture of the print](photo.jpg)

**Additional Requirements**
-----------------------

[M3 x D5.0 x L4.0 heat set inserts (optional)](https://www.aliexpress.us/item/3256802340684101.html)
**
Printing Considerations**
-----------------------

Printed with a 0.6mm nozzle in ABS with gyroid infill at 0.2mm layer height. If you can print bigger, it'll probably safe you some time.

This is a huge print, and will not fit on less than a 350mmx350mm bed without additional work.


**Credits**
-------

[Gridfinity by Zack Freedman](https://gridfinity.xyz/)
[Gridfinity templates by KptnAutismus](https://github.com/KptnAutismus/KptnAutismus)


Column for VR Skull

Column Body.3mf

Preview - DO NOT PRINT.3mf

**Description**

A 1x4 gridfinity holder to store an ergo kiwi in a convinient to grab and set back angle

![Picture of the print](photo.jpg)

**Additional Requirements**

[Ergo Kiwi](https://ergokiwi.com/)

**Printing Considerations**


Printed with a 0.6mm nozzle in ABS with lightning infill.

No real need for that diameter or material, print however you're comfortable.


**Credits**

[Gridfinity by Zack Freedman](https://gridfinity.xyz/)
[Gridfinity templates by KptnAutismus](https://github.com/KptnAutismus/KptnAutismus)

Gridfinity Ergo Kiwi Holder

**Description**


A 1x4 gridfinity tray to hold an pen or pencil in a convenient position to grab and replace. Also designed to sit atop a 1x4 bin with replacement pens/pencils underneath. Please see the next section for the specific ones I designed around.  

![Picture of the print](photo.jpg)

**Additional Requirements**


Note: These are not referral links, just providing the thing that fits. Other pens/pencils may fit too, but ymmv.

Cerpenter Pencil [Amazon](https://www.amazon.com/dp/B09SB3DGPB) [Aliexpress](https://www.aliexpress.us/item/3256804687207617.html)

Bic Gelocity Pens [Amazon](https://www.amazon.com/dp/B000F2SRN0/)

**Printing Considerations**


Printed with a 0.6mm nozzle in ABS with lightning infill.

No real need for that diameter or material, print however you're comfortable.

**Credits**


[Gridfinity by Zack Freedman](https://gridfinity.xyz/)
[Gridfinity templates by KptnAutismus](https://github.com/KptnAutismus/KptnAutismus)

**License**


CC-BY-NC-4.0 (See LICENSE.md )



Pen or Pencil Holder

**Description**


A large column for holding my VR headset via a random skull I found at Ross. Its printed in 4 parts and designed for a 350x350 Voron - and won't fit on smaller without tweaking the design/printing in pieces.

Its also designed to simply stack vertically, optionally with gluing the lid base to the lid for greater rigidity. The base is hollow for filling with sand, to help keep the column from printing. Additionally the center column is empty, and could be used for storage (or running the cord inside if you wanted to put a hole in the back of the column)

If you wish to change the height of the column - just adjust the body piece in fusion360 - it will recalculate the flutes to still look nice.

Finally, on the backside of the lid, there are spots for M3 heat set inserts. This is to allow for flexability in designing cable management, if needed. Just use whatever anchor points you need, and design whatever you like to fit.

![Picture of the print](photo.jpg)

**Additional Requirements**


[M3 x D5.0 x L4.0 heat set inserts (optional)](https://www.aliexpress.us/item/3256802340684101.html)

**Printing Considerations**


Printed with a 0.6mm nozzle in ABS with gyroid infill at 0.2mm layer height. If you can print bigger, it'll probably safe you some time.

This is a huge print, and will not fit on less than a 350mmx350mm bed without additional work.


**Credits**

[Gridfinity by Zack Freedman](https://gridfinity.xyz/)
[Gridfinity templates by KptnAutismus](https://github.com/KptnAutismus/KptnAutismus)



Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

jippen

iFixit Mahi case holder

Column for VR Skull

Gridfinity Ergo Kiwi Holder

Pen or Pencil Holder