The “Offset Snaps Removal Tool” helps you to remove Snaps - DS Part B from the Offset Snaps - DS Part A.

It comes with three parts: The plunger, the handle, and the pad.

Slide the handle into the long side of the plunger, then push the pad onto the top.

To use it, extend the handle all the way down, pinch the tip, insert it into your Snap, then pull on the handle to remove the snap.

To remove a quad connector (without snapping it), apply incremental pulls on each side of the connector until it loosens enough to be fully removed.

IMPORTANT: This remover only works with the new DS snaps, not the old ones.

Learn more about this part at https://multiboard.io/knowledge-hub

**Printing Guidelines:**

Use 5 wall perimeters for maximum strength.

Apart from that, the recommended settings apply: The printing orientation is as provided in the file. Printed at a layout height of 0.2 mm. It doesn't need printing supports. Use the default 15% infill. This part has been designed with a tolerance of 0.25 mm. Your printer will need to be able to bridge gaps of up to 30 mm for some designs. 

—

This object is part of Multiboard, a FREE "all in one" organization system with 700+ parts, that combines pegboard holes, honeycomb snaps, Gridfinity like bins, threads, brakes, and much more.

Explore and build the coolest, most adaptable workshop at https://multiboard.io

Offset Snaps Removal Tool

Offset Snaps Removal Tool.stl

This is a "Part B" Double-Sided Snap that connects to any Part A Snap.

**Printing Guidelines:**

Use 3 perimeter wall thickness, 0.2 mm layer height, 15% infill, and no supports. Apart from that, use your printer's default settings.

The printing orientation is as provided in the file. Make sure the downloaded files are .STL. This part has been designed with a tolerance of 0.25 mm. Your printer will need to be able to bridge gaps of up to 30 mm for some designs.

---

This object is part of Multiboard, a FREE and ridiculously modular organization system with thousands of parts to create the most adaptable workspace possible. Learn more and find ALL the parts at https://multiboard.io


Snap (DS Part B)

Snap (DS Part B) - Standard.stl

Paint tree supports on the base of the two connectors.

Designed to hold your propane or MAP gas cylinder securely onto your multiboard

**EDIT** I have changed the top part to have a moderate weight bearing snap so it doesn't come off by taking the tank off the mount.

#MultiboardRemix

Propane Torch Holder Multiboard.stl

Propane Torch Holder (bottom) (5).stl

Propane Torch Holder (top) (2).stl

**INFO** I have created a Bolt-Lock version of this model [here](https://than.gs/m/1397773) for those that are interested.

I searched for screwdriver holders but almost everyone I found required me to insert the screwdriver into a hole in a ledge. I wanted something that just allowed me to "grab & pull" the screwdriver off the Multiboard. The closet I found to what I wanted was from @Stranula on [Printables](https://www.printables.com/model/737539-screwdriver-holder-multiboard-multiple-mounts).

This gave me the incentive to try my own thing out and here is what I have created so far:
- Single Pushfit small
- Single Pushfit regular
- 6-Up Pushfit rail for small screwdrivers
- 6-Up Pushfit rail for 3 small and 3 regular

The small clip will take a screwdriver with a shaft diameter of 2.5-4mm
The regular will take a screwdriver with a shaft diameter of 3-6mm

I have printed them using Basic PLA and they seem to stand up well to multiple removal/insertions without loosing their springiness, but only time will tell :-) It was my first attempt in FreeCAD of using b-splines and creating a spring effect so I learnt a lot while trying to create these clips.

I printed using standard settings, only changing to 3 wall loops.

Yet Another Screwdriver Holder for Multiboard

Screwdriver Clip-Small PushFit.stl

This is designed to hold an aerosol can, canned air, etc. on your multiboard. It is attached via the overly strong pegboard clips and holds the cans at an angle. Two different models are provided, one with built-in support and one without if you'd like to add your own. It should be printed on the side to provide the most strength for the pegboard clips. The model is not oriented this way. The pre-supported model may have the slightest of sagging at the top of the cylinder but will print successfully on a Creality K1. To remove the supports around the pegs, use your side cutters to gently separate the supports from the pegs. It requires three horizontal pegboard spaces to clip in and is designed so you can butt them up horizontally to store multiple cans with no gaps in between (see pictures). Correct vertical spacing will have three open peg board holes between two of these holders.  There is a small triangular hole in the model for any spray nozzles your can's may have. Interior diameter is ~66mm and fits most air cans and US spray cans. There is a .STEP file in the download.

Multiboard Aerosol Can Holder Pegboard Attachment

MultiBoardCannedAir_NoSupports.stl

MultiBoardCannedAirSupports.stl

Its a pencil holder I use for pens, markers and remotes.
With dividers, also keeps your pens standing at attention. 

MultiBoard Pen_, Pencil, Marker

MultiBoard-Pen_Holder.stl

I could not get the standard Multiboard pegboard click hooks to hold my rubber mallet the way I wanted, so I put together this custom click hook for holding a rubber mallet with a head diameter of 65mm or less.

**Printing**
The printing orientation is as provided in the file. Use standard Multiboard printing parameters (0.2mm layer height, 3 perimeters, 15% infill).

**Assembly/Installation**
Install two of these on the same horizontal, leaving one column of pegboard holes between them. If your mallet is wider, you may need to leave two empty columns between them. Do not push on the curved/pointed end when installing or it may snap; despite this, I assure you it's strong enough to securely hold your rubber mallet once installed!

Thanks to [Keep Making](https://thangs.com/designer/Keep%20Making) for the excellent [Multiboard](https://www.multiboard.io/) system.

Rubber Mallet Multiboard/Pegboard Mount

Rubber Mallet Pegboard Mount.stl

**Description:**

Multiboard holders for Milwaukee M18 drills and impact drivers.
Left or right facing (your choice).
HD or LD (Recommend HD for full size/bigger).         
           


**Print Settings:**

**tl;dr:** 3/3/3 | 30% Gyroid | Auto Tree supports | Auto Brim

**Layers**: 3 Walls/3 top layers/3 bottom layers
**Infil:** 30% Gyroid 
**Supports:** Auto Tree
**Brim:** w/ 0.1mm gap

 

**Multiboard Interface:**

You will need these to attach to multiboard per drill/impact you are hanging up.  I.E. if you are hanging up 2 drills, multiply (x) by 2.

Per Holder:
(2) Heavy Weight-Bearing Hook Snap

https://than.gs/m/1130430

(2) Moderate Weight-Bearing Snap

https://than.gs/m/989145

(4) Small Thread - Multipoint

https://than.gs/m/1123334

Multiboard Milwaukee Drill &amp; Impact Holders  © 2025 by Aviator4x4 is licensed under CC BY-NC-SA 4.0. To view a copy of this license, visit https://creativecommons.org/licenses/by-nc-sa/4.0/


Multiboard Milwaukee Drill & Impact Holders

HD_Milwaukee_Drill_Impact_Hanger_Face_Left_v1.stl

**Multiboard Cable Clip**

Rotating locking cable clip for Multiboard Mid Threads.  Fits in snaps, and on the MultiBOOM!




Remixed and re-imagined: https://www.printables.com/model/126398-print-in-place-cable-holderorganiser-with-fusion-p

Multiboard Cable Clip

Multiboard_Cable_Clip_MidThread.stl

Multiboard Snaps can be pretty tight - here's a solution!  This meticulously-designed tool offers the brute force strength to pull out the most stubborn snaps!  ENJOY!

**Instructions:**
1. Screw deep into your Snap
2. Wiggle and pull!


**Print Settings:**
- 0.2mm Layer Height
- 5-6 walls loops/perimeters
- 25% Cubic Infill


Multiboard OctaPuller - Snap Removal Tool

MultiBoard-OctaPuller_Tool.stl

This shelf connects to [Moderate Snaps](https://than.gs/m/1311034) or [Heavy Hook Snaps](https://than.gs/m/1311032) and is secured using [Locking Bolts](https://than.gs/m/1310062). Keep in mind, Heavy Hook Snaps are stronger than Moderate Snaps but they don't work with flush mounted boards.

Special [support brackets](https://link.Multiboard.io/bolt-locked-shelf-support-brackets) can also be added to this Shelf for extra support.

This shelf is 2x2 cells (100x100 mm).

**Printing Guidelines:**

Use 3 perimeter wall thickness, 0.2 mm layer height, 15% infill, and no supports. Apart from that, use your printer's default settings.

The printing orientation is as provided in the file. Make sure the downloaded files are .STL. This part has been designed with a tolerance of 0.25 mm. Your printer will need to be able to bridge gaps of up to 30 mm for some designs.

For more information about printer settings, [click here](https://multiboard.io/knowledge-hub/printing-guidelines).

---

This object is part of Multiboard, a FREE and ridiculously modular organization system with thousands of parts, for creating the most adaptable workspace possible. Learn more and find ALL the parts at https://multiboard.io

4x4 MU - Simple Bolt-Locked Shelf

2x2 Bolt-Locked Shelf.stl

"Multibin Inserts" are placed inside of "Multibin Shells" to create a "Multibin". Multibin Inserts give the Shell the functionality to hold/organize specific items. 

This Multibin Insert is simply a Bin. A Label Holder can also be attached to this Insert. 

This bin is divided linearly at each cell, and one side (the front) has a curve to help you easily scoop out small items. 

Multibin Inserts can be secured to the Shell using 10x2 N52 Neodymium Disk Magnets that are held in place with "Bottom Magnet Holders".

Learn more about this part at https://multiboard.io/knowledge-hub

**Printing Guidelines:**

Use 3 perimeter wall thickness, 0.2 mm layer height, 15% infill, and no supports. Apart from that, use your printer's default settings.

The printing orientation is as provided in the file. Make sure the downloaded files are .STL. This part has been designed with a tolerance of 0.25 mm. Your printer will need to be able to bridge gaps of up to 30 mm for some designs.

For more information about printer settings, [click here](https://multiboard.io/knowledge-hub/printing-guidelines).

---

This object is part of Multiboard, a FREE and ridiculously modular organization system with thousands of parts, for creating the most adaptable workspace possible. Learn more and find ALL the parts at https://multiboard.io

3x2x1 CU - Curved - Divided Bin - Multibin Insert

3x2x1 - Curved - Divided Bin - Multibin Insert.stl

Use this “push-fit cap” to cover snaps or bolts that have a push-fit hole.

Learn more about this part at https://multiboard.io/knowledge-hub

**Printing Guidelines:**

The printing orientation is as provided in the file. The print has been designed to be “3 wall perimeters” in wall thickness. Printed at a layout height of 0.2 mm. It doesn't need printing supports. Use the default 15% infill. This part has been designed with a tolerance of 0.25 mm. Your printer will need to be able to bridge gaps of up to 30 mm for some designs. 

—

This object is part of Multiboard, a FREE "all in one" organization system with 700+ parts, that combines pegboard holes, honeycomb snaps, Gridfinity like bins, threads, brakes, and much more.

Explore and build the coolest, most adaptable workshop at https://multiboard.io

Push-Fit Cap

Push-Fit Cap.stl

This object is part of Multiboard, an "all in one" 3D printed storage system that combines the best of all other systems into ONE design.

With over 600 parts, Multiboard will give you almost everything you need. I'm talking bolts, honeycomb snaps, pegboard accessories, Gridfinity-style boxes, strong shelves, and much more.

If you want storage that adapts as your projects change, or if you want to blow away anyone who walks into your workshop... 

Then head over to https://multiboard.io to discover everything this system can do.

Have fun!

PS - If you're already a member and have no idea what this specific part is for, then go to https://multiboard.io/resources to learn how every part works.


Double Pegboard Click Hook

Double Pegboard Click Hook.stl

Multiboard

Activity related to collaborating with others on models

Likes, comments, and activity from your community

New content from your premium memberships

Emails and messages from designers you follow

Get notified when someone purchases your models or memberships

jcandthewires

Achievements

Novice Maker

Voyager

Seedling

Debutant