This is a simple case for USB power blocker for 3D printers, OctoPrint, or Raspberry Pi.

Found here: https://www.tindie.com/products/fatmannmakes/usb-power-blocker-inhibitor/

The alignment pins are very small, but I never had an issue printing them. Put a few drops of CA glue on the corners to seal.

Optionally can use some hot glue on both sides of the board.

USB Power Blocker Case

USB-VBLOCK CASE TOP1.stl

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3947429.

This thing Allows you to cure your hollowed out models through your drain holes. 

you can attached 2mm or 3mm fiber optic cable to the end of a UV flashlight and use this flexible wand to cure the inside of your model.   

Curing the inside of the model completely will help prevent models form leaking or potentially exploding do to leftover resin in the model.

UV Resin curing fiber optic flashlight wand 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3969147.

Jig for creating a Hobbed Bolt required for a Gregg's Wade's extruder.  it uses 2 608zz bearings

print as imported. 

removed left and right outer single wall (built in support) once print completes.

see Video for full how-to
https://youtu.be/UDiAeUjKYy0


Hobbed Bolt Jig

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4198083.

Slimagotchi case: Fits Pi 0W ( no header flush pins)  with waveshare 2.13 screen

Learn how to build  a "slim" pwnagotchi here: https://youtu.be/rlTzREaGmII

Checkout  case overview video here: https://youtu.be/KD7heRy_vDg

Checkout the how Pwnagotchi build series playlist on my channel page: https://www.youtube.com/channel/UC-dR6BpekOmCPXOGuXHGwdQ

Like my Design? Support me by buying me a cup of coffee!
https://www.buymeacoffee.com/1m0TocQ

Slimagotchi case (pwnagotchi_slim)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3363701.

This is a replacement cap for a  Enviro-Bottle 5 gal jug (3 Gal should be the same).
 It may fit other  5 gallon  bottles  

Thread go all the way to the top. 
you may want to add paper seal in the cap to prevent leaks like the originals came with.


Enviro-Bottle 5 Gallon bottle cap replacment

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3619991.

I recently cracked the tip of my toner, too many tools in the trunk.  so I decided to make a protective cap.  I was able to salvage the tip for now (crazy glue to the rescue).  it works, but it's a little loose on the PCB now and I get some feedback.  SO Stay tuned for a replacement tip "thing" in the  near future.

Enjoy 

Toner (inductive amp)   protective cap

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2877851.

Designed for a #6 Hillman nut (Lowes) and 1/2 screw.   Mount both  the plastic and metal disks  provided with the AP ( plastic  disk is flimsy on the AC pros and the metal disk helps). This should give just enough clearance so the 1/2 screw will be flush with the  top of the bracket.

Ubiquiti ceiling grid mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4016111.

m8 washers at different thicknesses
1.2
1.4
1.6
1.8

M8 spacers for  Greg Wade extruder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2912157.

 There are so many thumbwheels to pick from and I tried a few.  That said they always seems "not just right"   I liked the original adjustment wheels that came with my Monoprice Maker Select. They had some  heft to them that the printed ones did not. I had two issues with the originals.
1) My fingers would slip on the  splining out the outside of the wheel.
2) I always turned it the wrong why. ( I know lefty loosey. its a perspective thing)

This Thumbwheel cover is my attempt to address those issues and still keeps the  hefty feeling of the originals.

 I would love to see everyone's Make and get your feedback for improvements. 

This cover is what works for me. I figured  maybe someone else would feel the same. so give it a try and let me know!

V8 added: adjusted  outside diameter for better clearance.




Maker Select 2.1 / Wanhao   Thumbwheel Bed Leveling covers

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4198080.

Standard pwnagotchi case 

Build your own pwnagotchi!!!   instructions  here: https://youtu.be/Gw4yCRKLn3Y

Checkout  case overview video here: https://youtu.be/KD7heRy_vDg

Checkout the how Pwnagotchi build series playlist on my channel page: https://www.youtube.com/channel/UC-dR6BpekOmCPXOGuXHGwdQ

Like my Design? Support me by buying me a cup of coffee!
https://www.buymeacoffee.com/1m0TocQ

Pwnagotchi case

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

fatmann66

Achievements

Seedling