Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3868959.

This was a quick project for my mother-in-law, to help remind her if the dogs have been fed or not.  

Yes, the lettering isn't centered.  I didn't want to put in the effort and just roughly eyeballed it.

Tolerance on the slider is 0.5 so even when you don't have the perfect tune it will slide freely without falling off.

Dog Feeding Reminder Sign

These parts fit a 1 1/4" PVC Pipe and a wood cross bar.  I used a trim piece that is L shaped to provide a front lip for the art.  The "brace" piece gives you a small back lip to keep things from falling backwards.  Everything prints without supports and is designed to give 2 points of support on each side of the wood cross beam which tightens up the square.

Screws that go through the PVC are 2.5" #10-32 machine screws.  

2" #10-32 for the screws that go through the wood and the spacer+PVC2nd

1" #10-32 for the holes through the wood and PVC part.  

I used wing nuts on all of it for easy assembly and break down. 

If you do not have a drill press to drill all the way through both sides at once use the following method with a hand drill:
To align them straight, place the PVC on the pipe at the height you want, drill your hole, place screw in hole to old it in place and lay flat side down at the edge of a table.  Use the template laying on the flat side to mark the second hole at the same angle.  Drill your hole, use a 1" screw to hold it, turn it over and mark the hole on the second side, drill and now you have a straight hole.  


PVC Art Shelf Brackets

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2737876.

Was inspired by this model: https://www.thingiverse.com/thing:2681295

This GPU stand is designed with a rear support so the card isn't simply hanging. Its also go a central bridge for even more support under the PCIe Riser. The riser stand slips into holes that are 20mm x 5mm in case I decide to expand on use. The riser bridge can be removed and upgraded. The front supports mounting of a 120mm fan. Holes are spaced for 105mm x 105mm. I modeled the holes for use with a noctua anti vibration pegs in case I didn't want to use screws. I wanted these to interlock so I could add more in the future without them sliding around. If you have any suggestions on upgrades or addons, feel free to let me know and I'll see what I can do. 

Update: 
v8 has been uploaded. Includes rear interlocks as well as extenders for use to mount these back to back. Extended Rear riser brace.

Test your tolerances with the Joint Test Files. This will save you plastic printing the whole stand just to find out you need to fix something for the joints to connect.

NEW: Quick release pin - Print at 200 resolution and 100% infill

GPU Stand For Mining Rig

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2863759.

Filament stand.  Pretty plain and simple. 

Big enough to hold all of the different 1kg spools I have.  It is untested for spools bigger than 1kg.

Print 2 and hook them up back to back.

10/24/2018 UPDATE

I added a slightly shorter version that fits on my FFP Clone.  Still fits 1k rolls.

11/9/2018 UPDATE

New Rod with bearings for smoother rolling.

11/10/2018 UPDATE

Added a 4th bearing for a more even support of the spool.

ecspot Filament Stand

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1904482.

I liked the Dream 3D Nutcracker but it was too tall for my printer.  I didn't want to shrink it so I split it in half and added a pin to line it back up.

Dream 3D Christmas Nutcracker Split

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2001739.

This is a model of the Mission San Juan Capistrano in California.  It is by no means to scale or even accurate in its design.  Its meant to simply represent a close rendering of the mission.  

I designed this for my daughter and Its going to make a great addition to her 4th grade mission project.

Update: I have added the side buildings and the old destroyed mission we created as well.  Enjoy.

Mission San Juan Capistrano

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2183183.

This design uses 3 x 6.4mm by 1.6mm rare earth disc magnets.  I started with 2, but got better magnetic pull with the third.  

https://www.rare-earth-magnets.com/magcraft-nsn0657

The screws for the frame part are #4 x 3/4" wood screws

http://www.homedepot.com/p/4-x-3-4-in-Philips-Brass-Flat-Head-Wood-Screws-4-per-Pack-809521/204275704

The bolts and nuts on the door are #8 32 x 1/2"

http://www.homedepot.com/p/Everbilt-8-32-tpi-x-1-2-in-Zinc-Plated-Round-Head-Combo-Drive-Machine-Screw-8-Piece-803091/204274611

Lack Table Enclosure Magnetic Door latch

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1894947.

Knob for stove fan

Added a second version with the whole turned 90 degrees. 

Stove Fan Knob

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3003912.

The grooves push into the center of a pool noodle so no glue is required.  I print this straight up and down with a brim of 20 lines and 3 layers.  This probably isn't needed but for me keeps the rod from falling over accidentally.  The whole for the connecting screw is thread tight so you could probably get away without a nut, or use an M5 nut for the end.

GoPro Float using Noodle

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1894757.

Storage for some tools

added a second version with slightly deeper holes on the bottom level

QIDI Filament Removal tool Holder Clip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4660994.

Wanted something very simple to mount on my 1010 desk. Made this so I could create more inserts for different types of things. Easily interchangeable. Minimal supports needed for insert. Base can print with no supports.

Made mounting holes large enough to secure with a 1/4-20 nut. sunken in so you could cap them to hide the nuts.

Headphone Holder for 1010 extrusion (or wall)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2404631.

Many fidget spinners use bearings for weights, but even cheap bearings cost 50 cents.  I know many of us started designing around Nuts but there are still many design that use bearings.  I made a container that holds 3 pennies and fits into the bearing slots.  Now you can spend a little plastic + 3 cents and the weight is very close.

These are designed for PLA shrinkage.  Other materials may shrink more or less causing them to be too tight or too loose.

Fidget Spinner Bearings To Pennies

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4655065.

Wanted something very simple to mount on my 80/20 desk.  Made this so I could create more inserts for different types of things.  Easily interchangeable.  Minimal supports needed for insert.  Base can print with no supports.

Made mounting holes large enough to secure with a 1/4-20 nut.  sunken in so you could cap them to hide the nuts.  

Headphone Holder for 80/20 extrusion (or wall)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3547559.

The original cable holder from prusa and included in the mk2.3 mod was a little too wide and the cable ties would prevent the x carriage from hitting the endstop.  This modification takes out a little of the bulk from the part and has allowed mine to work.  Thought I'd share it incase anyone else is having this issue.

IMPORTANT:  when I imported it to Fusion the file adjusted to 395mm instead of 39.5mm.  I didn't know how to shrink it so you'll need to adjust the print to 10% size in your slicer.  If anyone knows how to fix this, I'll edit it and upload the proper size.

MK2.3 Cable Holder Remix

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1897541.

Holder for paint scraper type removal tools

QIDI Print Removal Tool Holder Clip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1902319.

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/9gUgoW34XwG

Milton Security Logo Cookie Cutter

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3221203.

These drop ceiling clips require 2 M3 screws and nuts. Rotate them to print on their side.

Drop Ceiling Rail Clips

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1902235.

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/jbl30AS6rwM

2" hole grommet

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1858889.

I couldn't find a belt buckle that was big in the right shape and color for the costume so I attempted to create one.  

Hagrid Belt buckle

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:1912172.

Spinner broke on Twister Game?  Print this out as a replacement.

Twister Spinner Replacement

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

ecspot

Achievements

Seedling