Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6434798.

Cap to cover [Comet](https://en.wikipedia.org/wiki/Comet_(cleanser)) cleanser can (scouring powder)

How this differs from other designs ([Cap for Comet Cleanser Container](https://www.thingiverse.com/thing:2683262), [Powdered cleaner lid](https://www.printables.com/model/575305), and [cap for cleanser canister](https://www.printables.com/model/57752)) is I wanted something smaller to print faster and use less filament. To this end, the cap inserts into the seven hexagonally arranged holes in the lid, instead of covering the entire top.

Press on and it should stay in place using friction. To remove, pry off with a slotted screwdriver.

Comet cap compact

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6422298.

Socket organizer remixed to use a 1/2" x 1/16" aluminum bar (instead of 3/4" x 1/8")

The adapters slide onto the bar and should fit tightly (file down as needed) with a friction fit, so no end caps are necessary

Also includes optional embossed text labels

The 1/4" adapters are dual-sided (based on kmac1036's remix), and 3/8" are single-sided (based on the original design by bross)

Socket Organizer - for 1/2" x 1/16" aluminum bar

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6422346.

Holder for screwdrivers of various sizes. Requires a 1/2" x 1/16" aluminum bar to slide onto.

Similar to [Socket Organizer](https://www.thingiverse.com/thing:3779736) but with round holes for screwdrivers

Uses the same 1/2" x 1/16" bar size as in [Socket Organizer - for 1/2" x 1/16" aluminum bar](https://www.thingiverse.com/thing:6422298)

Works best for Phillips screwdrivers, Craftsman Phillips #3 to #0 (model numbers: 41555 H WF, 41555 J WF, 41416 H WF, and 41416 J WF). Fits looser on the bar than my socket organizer, intended to be held up lengthwise (see photo) and affixed at each end.

Screwdriver holder rail

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6422398.

Replacement for TowelPart1_V2.STL of [Paper Towel Holder v2](https://www.thingiverse.com/thing:1526585), using magnets to hold the removable part in place instead of a clip, for increased durability

Press four 6x3mm round magnets into the holes at the top of the bracket

Reuses the other parts of the original design (since I had already printed them). To insert magnets into part 4 (not included), you can drill 13/64" holes, file to fit, and press four additional 6x3mm magnets (total eight magnets). Line up the polarity to attract.

Paper Towel Holder v2 - with magnets

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6422557.

Cover to plug the hole for extra hacksaw blade storage

Fits the Milwaukee High-Tension Hack Saw with 12 in. 24 TPI Bi-Metal Blade and Blade Storage (48-22-0050). Press fit in, and pull out from the lip.

Includes recessed text label ("blades")

Hacksaw blade storage cover

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6422431.

Replacement for part 3 of [Paper Towel Holder v2](https://www.thingiverse.com/thing:1526585), adding a gusset for improved strength.

Paper Towel Holder v2 reinforced Part3

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6424827.

Replacement tugblock buckle for the Kryptonite Transit FlexFrame U-Bracket bike lock frame mount. Useful if you lost the tugblock (metal buckle) and nylon strap at 0:34 in https://www.youtube.com/watch?v=lULcuifzxPs&t=0m34s (official installation video from KryptoniteLocks) but have the other parts.

Parts required:
- Bracket body from the original Kryptonite mount (both pieces)
- M4x20 bolt
- M4x12x6 heat set insert
- Zip ties 8" (2)

Installation instructions:
1. Insert the printed part into the bracket body, with the hole visible through the other end
Note: will be a tight fit, using a heatgun to soften up the part may be helpful
2. Insert the heat set insert into the hole by heating up with a soldering iron
3. Attach the other piece of the bracket body, and screw in the bolt - it should fit securely
4. Insert zip ties through the slits on the other end, and loop through your frame

See also other designs, and how this one differs:

[Kryptonite bike lock holder](https://www.thingiverse.com/thing:4384624) - slides into the shackle instead, using no parts from the original mount. I tried this design first but found it limiting due to requiring an offset mount - the official FlexFrame mount supports many different positions, which are possible with my replacement tugblock - as long as you have the other parts.

[Kryptonite lock adapter for bicycle rack](https://www.thingiverse.com/thing:4950243) - only interfaces with half of the bracket body (and is designed for a rack), vs mine which requires both pieces.

Notes:
The hole is sized to accept a brass heat set insert for a M4 bolt, not a bolt by itself. First design allowed threading the bolt directly into the plastic, but this wasn't secure enough in my testing. Using a threaded insert adds significant amounts of rigidity. YMMV.

Kryptonite bike lock tugblock buckle

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

dauw

Achievements

Seedling