Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5657804.

Standard shop vac connection that will work with most house vacuum hoses, and the smaller popular Ridgid "car kit" hose.

Also on Printables:
https://www.printables.com/model/325157-25-shop-vac-to-1625-1-58-threaded-hose-fitting

2.5" shop vac (male) to 1.625" (1⅝") threaded hose fitting

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5657848.

DeWalt Miter Saw vac port that will connect to most house vacuum hoses, and the smaller popular Ridgid "car kit" hose.

Will likely work with more DeWalt miter saws than the DWS779 I have, but YMMV.

This thread works with many (most?) household vacuum hoses. I harvested an old Eureka hose (the black one pictured), an ancient whole house vac hose, in addition to the Ridgid shop vac “car kit” hose, and it seems to work well for all of them. It will fit almost any vac hose with a 1⅝" outer diameter (41–42mm). 

Also on Printables:
https://www.printables.com/model/325215

For the other end of the hose, you may want: https://www.printables.com/model/325157

DeWalt DWS779 Miter Saw to 1.625" (1⅝") threaded hose fitting

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5659173.

Also on Printables:
https://www.printables.com/model/325823

Single mount that fits most shop vac attachments: large 2.5" (2½"), small 1.25" (1¼"), and oddball Ridgid 1.875" (1⅞")

Mounts horizontal or vertical, including the underside of a shelf or on the ceiling, depending on the weight of the attachment. Use 0.3mm layer height for additional grip.

Single mount that fits most shop vac attachments: 

- standard large 2.5" (2½") fits the outer petals
- standard small 1.25" (1¼") fits the inner petals
- some oddball Ridgid 1.875" (1⅞") will fit inside the outer petals (see last photo)

Two model versions: 

- First version only includes the outer petals (2.5" and some 1.875")
- Second version (*updated 2022-11-27*) includes mounts for all three sizes, but uses more filament.

**Update 2022-11-27:** Previously uploaded the wrong iteration of the all sizes mount. Replaced here with the "V9" files.

Shop Vac Attachment Mount for 2.5", 1.25", and some 1.875" (1⅞" Ridgid)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5375886.

Scout trophies for Pinewood Derby cars. 

I printed about 50 of these, with a total filament/material cost of just over $100. This will save our Pack several hundred dollars a year. Get started early as it can take a few weeks.

Any tips received for the model go back to Scouting. If you print a bunch for your Pack, consider donating a small amount for our Pack. Thank you!!

Also on Printables:
https://www.printables.com/model/191612-scout-pinewood-derby-car-trophy

Scout Pinewood Derby Car Trophy

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5190343.

Add-on to [Filament Spool Holders by 3DStartups](https://www.thingiverse.com/thing:2987304).

End cap works as a cam lock to prevent the arm from disengaging prematurely. Cap can be pulled out with no effort, but once inserted, the spool holder locks together much better.

v2 uses a tighter tolerance than v1, so you can remove the top arm completely. This allows the filament reel to angle/turn as needed when spooling.

Both v1 and v2 can be resized +/- 5% in your slicer to get the fit you like. Good luck!

Also on Printables:
https://www.printables.com/model/114562-endcap-lock-for-filament-spool-holder

Endcap Lock for Filament Spool Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5659270.

Also on Printables:
https://www.printables.com/model/325859

Replacement mounting cams for the side trim on a 2014 Subaru Outback.

The kids used the trim on my 2014 Subaru Outback as a step, and broke off several of the plastic mounting cams that hold on the side trim. As far as I could tell, Subaru only sells replacements with the entire trim, which would mean waste money and more plastic in our landfills. :-p

Trim Mount Cam for Subaru Outback 2014

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5950211.

Dual-sided 4" QuickConnect (Rockler-compatible) OD, with different tapers on the ID to fit various hoods and machines.

Also on Printables:
https://www.printables.com/model/442279-4-quickconnect-dust-hose-adaptor-with-asymmetrical

Store bought 4" dust collection fittings are ridiculously inconsistent in size. I have two very similar dust hoods with different ODs, and I made this adaptor primarily so I could use them both with my Rockler DustRight “QuickConnect” hose.

The outer diameter (OD) on both sides fits the Rockler hose/handle, and the inner diameter (ID) has differ tapers on each side to fit a variety of machines and other 4" fittings like the hood pictured. 

PETG recommended over PLA for strength and flexibility.

Tip: I made this a bit longer than needed, so I could mount it to a ball-joint tripod near my lathe. So unless you need that length, save yourself from plastic and print time by scaling the height disproportionately.

Let me know how you adapt it to your own needs.

4" QuickConnect dust hose adaptor with asymmetrical inner diameter tapers to adapt different fittings

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

cookiecrook

Achievements

Seedling