Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6094012.

Wanted to slow down the FPS for use in a low-speed game. Tested different lengths to see how it affected speed. With Adventure Force and Dart Zone short darts, the 60mm and 100 mm resulted in about a 10 FPS drop. The other length of SCAR seemed negligible. Using the darts that it came with resulted in about a 20 FPS. Not sure if the shorter than 60mm SCARS actually help with accuracy as they lose some of the rifling that causes the spin. 



X-Shot Longshot Trivictus SCAR

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5927817.

Couldnt actually attach anything to the original version's rail. This remix fixes that by adding more room between the rail and the adapter.

Rail is from one of CaptainSlug's builds (don't remember which one).

Nerf Picatinny stock adaptor - Remix

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5413339.

Replacement for the nub on the movement stick on a NeoGeo Pocket Color. It may also work on a non-color version, but I don't have one to test. 

NeoGeo Pocket Stick Nub

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5211078.

Update: added Mega_Talon_RearMag_v2.stl the original was not the correct length...thanks gabycms for pointing it out!

Here is my latest rear load inline mag mod. I went a little crazy and it holds 9 rounds! Even made some instructions this time. Hitting on average 100fps with 3" of brass barrel. It does double feed sometimes based on how you "reload" with the inline mag. To avoid the double-feed I'll tip the blaster barrel down to seat a dart and then tip it back up to get the other darts out of the way. If anyone knows of a way to fix this another way, let me know!

Muzzles- 
https://www.thingiverse.com/thing:4792121

Grip cover - 
https://www.thingiverse.com/thing:4322798

Handle extensions - 
https://www.thingiverse.com/thing:4790442 
or 
https://www.thingiverse.com/thing:3178982

Quick Point Sight-Pistol
https://www.thingiverse.com/thing:4882220

Nerf Mega Talon 9rd Inline Mag

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4790445.

My remix of https://www.thingiverse.com/thing:4713483.

Hardware you will need. Listing McMaster-Carr parts #s

will need one of these for the breech -
Oil-Resistant Buna-N O-Ring
1/16 Fractional Width, Dash Number 012
9452K21

and 6 of these but I'm sure there's a ton of other screws that will work -
Steel Phillips Flat Head Screw
82 Degree Countersink Angle, 4-40 Thread Size, 3/8" Long
90273A108

And finally, you will need a length of 17/32" brass barrel. to stick in Mega_Inline_Brass_4rd.stl. The brass should seat 1cm in the part and glue if needed. 
I used 2.5" of brass but haven't tested what is most efficient. Getting 75 - 100 fps.

Build includes this Picatinny hand stop: https://www.thingiverse.com/thing:4154584

Grip cover -https://www.thingiverse.com/thing:4322754

and a couple of remixes
https://www.thingiverse.com/thing:4790443
https://www.thingiverse.com/thing:4790442


Nerf Mega Bigshock Rear load Inline Mag Mod

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4792121.

a bunch of muzzles for https://www.thingiverse.com/thing:4713483 or my rear load remix.

Mega Bigshock Frame by TimETraveller8 Muzzles

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4741774.

This is a remix from https://www.thingiverse.com/thing:398515

This remix adds some custom parts and replacements for some of the aluminum parts

2 sets of nameplates (side plates):
Hex - hex all the things
TF - just the initials of the blaster.

TFU_Trigger_Flat - A flat trigger with some mods to tighten up the spec for less slop.

Custom rams and pushers:
TFU_Pusher - just the undercut pusher.
TFU_Ram_Undercut_Taller - uses the stock ram and a custom undercut pusher.
TFU_Ram_NoCut - uses the stock ram and a straight pusher.
TFU_Ram_Shorter_Undercut - a slightly shorter ram with undercut pusher.
TFU_Ram_Shorter_NoCut - a slightly shorter ram with a straight pusher.

TFU_PrimingBar - Replacement for the aluminum bars that are normally used. I printed mine with 5 walls and 99% infill and I'm not getting any flex. You may get away with less.

TFU_UChannel_Back_Dovetail 
TFU_UChannel_Front_Dovetail
Replacements for the aluminum U- Channel. I printed with 5 walls and 75% infill and they are solid. Dovetail should hold the two pieces together nicely.


 Talon Fang U Remixed Parts

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4862037.

Use these pieces to convert your Retaliator to use short darts with a 17/32" brass barrel. 

The back of the pusher uses the o-ring from the old Retaliator breech. The front of it uses an o- ring from a Caliburn or TC pusher (McMaster part #9452K21)

Pick one of the barrel adapters based on barrel length. I used 5.5" of 17/32" brass and the _Long adapter. Brass slides into the adapter, adapter slides in the barrel lug part of the Retaliator. See pic for how far it should sit but you just want to make sure there is clearance for the darts and the pusher has room to seal in  the barrel

_BarrelIndexer is to keep the brass straight in the Retaliator faux barrel.


Nerf Retaliator Brass Barrel Short Dart Conversion

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4870302.

A remix of the TecTen so you can use a 17/32" brass barrel instead of 9/16"

Use a piece of 17/32" brass in the PT Adapter. Cut to the length of the adapter.

I used a 5.5" piece of 17/32" brass for the barrel but you could probably get away with more or less.

Pusher uses 2 o- rings from a Caliburn or TC pusher (McMaster part #9452K21)

I ended up using one of these muzzles but include an original one that fits on 17/32" brass
https://www.thingiverse.com/thing:4792121

17/32" Brass Barrel TecTen Remix

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4550456.

Edit(08/18/20) - Added an A2 muzzle that fits onto Brass to Aluminium.stl for if you want to take off the SCAR for some reason. Also added a 3 round back and a short and long front. Mix and match to your barrel length needs.

This is another iteration of my in-line mag for rival blasters. This time I threw it in a Nerf Takedown and added a barrel cover. 

Decided to add the SCAR later. Used one of these - https://www.thingiverse.com/thing:3876214
https://www.thingiverse.com/thing:3884344
and made an adapter for it to fit on the brass (file - Brass to Aluminium.stl) and a barrel cover to protect the brass (file- Rival Inline - Brass - 50mm Shroud.stl)

Nerf Takedown in-line mag and brass barrel 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4822793.

A quick way to get a brass barrel in the x-shot recoil and a couple of visual mods too.

Rail is from here - 
https://www.thingiverse.com/thing:2785061

Muzzle from here - 
https://www.thingiverse.com/thing:4792121

X-Shot Recoil brass barrel and visual mod

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5139035.

The screw post kept breaking so I redesigned it similar to the printable Nexus grips. Put the pins through the holes on the ceda or prime and then slide the grip over. Use some nerf screws to screw together. 

CEDA / Gameface Prime M4 style Pistol Grip - Remix

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4517420.

Just a quick remix to fit a 150mm height printer and reduce the need for supports (still may need them).

(150mm Height) - Nerf Mega Bigshock Inline Magazine (inline clip) w/ Tanker Muzzle Break

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4495637.

Another pass, this time with different muzzle types that you can swap.

This is a 4 shot inline mag for the Nerf Mega Bigshock. It allows you to put 3 short (3.5mm) darts in the mag and one in the barrel. To reload, tip the barrel down while priming and then fire away.

Materials:
This print
One 40mm length of 17/32 brass tube
Some tape or glue

First, you will need to take out the AR and dart post by whatever method you want but you will need a clear path to the back of the blaster. I used a flat head screwdriver to pry the cap on the back of the barrel off. If you are careful it can be glued back on or print and eventually, after test fitting all the parts, glue in one of these

https://www.thingiverse.com/thing:2235606

https://www.thingiverse.com/thing:1277598

Once you have a clear path to the back of the blaster you can test fit the print and use some tape to get an airtight seal and allow the print to seat all the way back. Also, make sure the sight is on top, and the channel lines up with the plunger tubes air hole.

The next step is to cut 40mm of 17/32 brass tube. Make sure all the rough edges are sanded smooth and a dart can slide in without catching. Test fit the brass in the end of the print, it should seat on a lip inside. If it's not airtight try a layer of tape or you may want to glue it in.

In the end, you may want to glue the print into the blaster to make it perfectly airtight but I'm getting acceptable performance without gluing the print in the blaster or gluing the brass in the print.

Nerf Mega Bigshock Inline Magazine (inline clip) w/Swappable Muzzles

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4521442.

Updated - 6/29/21 - Added a new "Bigger Flare" file. This had a bigger flare at the back of the inline mag for easier dart loading. To use this you must remove the AR from the Knockout.

Updated - 7/5/20 - Added a spacer to put at the tip of the silencer to help align everything.

Updated - 7/4/20 - Didn't like how it wasn't opening the AR properly. Fixed the lip

EZ Brass Barrel / in-line mag

If you'd like a brass barrel for your TKO build, use this and a length (I'm going to cut flush with the silencer once it's all together. Seems to be about 3" but the Knockout can take way more.) of 17/32" brass tube instead of the polycarbonate tube from the instructions. 

I'd suggest gluing in the brass barrel and adding some tape to the print, where it goes into the blaster (or do the tape and o-ring trick from the original instruction videos), to get a good seal. I'll maybe update the print to accept some o-rings but I need to get some that are the right size and do some testing. 

EZ Brass Barrel / in-line mag for TKO 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4482223.

This is a 4 shot inline mag for the Nerf Mega Bigshock. It allows you to put 3 short (3.5mm) darts in the mag and one in the barrel. To reload, tip the barrel down while priming and then fire away. 

Materials:
This print
One 40mm length of 17/32 brass tube
Some tape or glue

First, you will need to take out the AR and dart post by whatever method you want but you will need a clear path to the back of the blaster. I used a flat head screwdriver to pry the cap on the back of the barrel off. If you are careful it can be glued back on or print and eventually, after test fitting all the parts, glue in one of these

https://www.thingiverse.com/thing:2235606
https://www.thingiverse.com/thing:1277598

Once you have a clear path to the back of the blaster you can test fit the print and use some tape to get an airtight seal and allow the print to seat all the way back. Also, make sure the sight is on top, and the channel lines up with the plunger tubes air hole.

The next step is to cut 40mm of 17/32 brass tube. Make sure all the rough edges are sanded smooth and a dart can slide in without catching. Test fit the brass in the end of the print, it should seat on a lip inside. If it's not airtight try a layer of tape or you may want to glue it in.

In the end, you may want to glue the print into the blaster to make it perfectly airtight but I'm getting acceptable performance without gluing the print in the blaster or gluing the brass in the print. 

This is the first from-scratch design that I have done so let me know how it performs and any feedback. May do some strictly visual remixes just for fun but maybe one of you will beat me to it! 

Nerf Mega Bigshock Inline Magazine (inline clip)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4482803.

Same as before but this time with an A2 style flash hider. 

Used this as a starting point for the flash hider
https://www.thingiverse.com/thing:741776

Haven't printed one yet but it should work just as good as the original model. 

May need supports for this one

Update: Had a messed up area where the brass should seat. It should be good to go. Will test soon

Nerf Mega Bigshock Inline Magazine (inline clip) w/ A2 Flash Hider

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4397316.

Remix of thing:4362395 so I could easily add a 17/32" brass barrel.

HYPR Brass Barrel Extension 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4563533.

Needed an extended mag release lever so I could use the wild card adapter in my Nexus. Its kind threw together but "good enough"

Couldn't pull off a supportless design so def need supports.


is a replacement for TKrelease.stl from here - https://www.thingiverse.com/thing:3245243


Wild Card Adapter Extended Release Lever

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4790443.

Found that the original didn't fit on the Picatinny rail that I had. Remixed tolerances for rail and filament. 

You will need to scale the pin. I found 95% (not length) to still be tight 

Picatinny Iron Sights Remix

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4790442.

A shorter version of https://www.thingiverse.com/thing:3178982.

Nerf Mega Bigshock Priming Handle Extension

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4560183.

This is an adapter to use a SCAR for 16mm barrels on your Adventure Force Nexus Pro.

I used it to add a Tenacious Twist (https://www.thingiverse.com/thing:3906599) to mine. Still trying to figure out if I like the tight or loose fit version.


Adventure Force Nexus Pro to 16mm Adapter

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

braytonmatheson

Achievements

Seedling