The top is open so you can slide your CDs in and out with ease from the top. Sides have cutout to save material, as well as to show the sides of the cases. 

Mirror the mount in your slicer so you get both the right and left version. 

Blu-tac it or use double sided tape to mount it to your wall. Doesn't need support. This is optimized to use as little material as possible, so you can get these printed very quickly, took me 40 minutes per pair and can probably be quicker. 

CD Jewel Case Wall Mount Display

The top is open so you can slide your CDs in and out with ease from the top. Sides have cutout to save material, as well as to show the sides of the cases. 

Blu-tac it or use double sided tape to mount it to your wall. Doesn't need support. This is optimized to use as little material as possible, so you can get these printed very quickly, took me 40 minutes per pair and can probably be quicker. 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4703069.

Update from original: 
Replaced the M10 coupler with dragon's grove mount coupler, which I believe has less play. 
Also features a waffle pattern at the bottom of the carrier plate. The pattern is experimental and intended to make the print a lot easier to remove. If it causes any print problems please let me know and use the No Waffle version. 

The stand-offs and the logo are exactly the same as the original.  

Print settings follow the original work by ML3DPrinting

Anycubic i3 Mega X-Carriage [MK4] Phaetus/Trianglelab Dragon V1.2

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4598196.

Update: 2020-11-28: I noticed some wear on the Teflon tubing so I tried some 4mm polished stainless steel rods and the friction is noticeably bigger. However, it works ok for relatively full spools, but lighter spools do not work well. 

Heavily inspired by the spool holders on Voron printers. Never seen PTFE being used for spool holding and I would like to give it a try. Designed to fit 4mm PTFE tubes and the stock I3 Mega S spool holder. My main concern is that the PTFE wouldn't be very wear-resistant, so I would like to try other materials such as polished stainless steel rods in the future. But if the Voron designers chose PTFE there must be a good reason. 

Just print both halves (they are slightly different to avoid interference with the holder) and slide them onto the holder. It is a tight fit so don't be afraid to play with scaling and horizontal expansion. 

Print with the flat side down, shouldn't need support. Material doesn't matter, I used 0 infill and 3 shells. 

Anycubic i3 Mega S PTFE Spool Stand

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4901062.

Modded the step file from an already excellent extruder to suit my needs. 

To build the exact extruder as pictured, you need to print all 4 parts (remember to mirror the end_plate and midsection) along with the mirrored version of the original M4 STLs (except the main body and the end plate since you'll be using this modified design). 

Modifications from the original:
Changed the end_plate mounting holes and hole position to accept M3 screws
Added an angled mounting bracket to allow the hatch to open while maintaining a small footprint
Altered the coupler design to a 3D printable one, which also has zero play because it uses ridges to clamp onto the PTFE tube. 
Removed the stud on the end_plate to suit my coupler design. 

Hardware needed:
2 M3 nylock nuts and 2 M3*12mm bolts to mount extruder to the mounting plate
2 M3 nuts, 1 M3*10mm bolt, and 1 M3*8mm bolt for the coupler. 

Print Instructions:
Use bridging, no supports needed, orientation is exactly as STL orientation. 
Use the Voron M4 print settings and material for end_plate, midsection, and ultra coupler; bracket works fine with any material but needs good bed adhesion (I used PETG). 

Anycubic i3 Mega/S Voron M4 Extruder Mod

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4487923.

These knobs just can't be torqued enough by hand, but I didn't want to damage them further by using channel locks either, so I designed this custom wrench just for them. Before you print the whole wrench, print the Knob test fit first to make sure the fit is right. You can adjust horizontal hole expansion to tune the fit of the knob. After you get the fit dialed, you can print Ver A4 Perfect.

I used some topology optimization and static analysis because why not.

17cm long from end to end

Swagman Knob/Nut Wrench

Some parts of the logo may be too thin to be durable, especially the leaf part, so feel free to use horizontal expansion in your slicer or scale the logo to make the features thicker.

STEP files and alternate versions included for your modding conveniences

basecolor <= 2mm < logo color for the badge file

Base plate for the badge has dimensions of 110mm*43mm

-Original logo belongs to halleylabs.com

Halley Labs Badge and Logo

stl version of the badge, good for printing

Halley Labs Badge.stl

Mechanical engineering student at Stanford, with interest in mechanical designs and robotics.


Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

<div class="markdown"><p>Mechanical engineering student at Stanford, with interest in mechanical designs and robotics.</p></div>