Edilgen Blocks are originally designed to make furnitures like desk, stool, shelf, bench, organizer etc.

However, you can use them to make anything you can think of. Other ideas I had were: Pen holder, toilet paper holder, plant holder, toothbrush holder, baby cart for fun! Yes, Edilgen Blocks have "the Wheel" compatible with other blocks.

Downloadable 3D models are human size, like you can make yourself a desk with them.

1:2 or 1:3 scales are the best to make toys for kids, 1:3 size is tested for full functionality with no issue but smaller scales might not work properly.

The 4x3 desk sizes are: 88x66x75 cm and weights around 5 kg

I used default printer settings (infill 15% gives enough strength)

***For Half ball make infill 1% and wall loops can stay at 2 for the max Weight/Strength ratio

Please support me by following on Social Media platforms:
https://www.instagram.com/tahaedilgen/
https://www.tiktok.com/tahaedilgen/
https://www.twitter.com/tahaedilgen/
https://www.youtube.com/shorts/qiBAv_-TLxA

The downloadable files for these models are for personal use only. Commercial use, distribution or modification of the models can be authorized via Patreon: https://www.patreon.com/tahaiswilling

#FunctionalArt contest attendee :)

Edilgen Blocks

the PLATE v5.stl

corner T v5.stl

corner L v8.stl

duo L v8.stl

duo T v7.stl

quad T v7.stl

quad L v8.stl

the SHOOTER v1.stl

hoop adapter v4.stl

basket hoop v7.stl

half ball v6.stl

Organize your desk with this Air Pods, Apple Watch and iPhone holder.

The model does NOT require any supports and consist of 3 different parts (9 pieces in total)

You just need to glue the "wheel hub" into the slots in chassis. Rest is straight forward wheel attachment.

The downloadable files for these models are for personal use only. Commercial use, distribution or modification of the models can be authorized via Patreon link below:
https://www.patreon.com/tahaiswilling

3D PRINTING SETTINGS
Layer Height = tested in 0.2 mm
Wall Line Count = 3
Infill = 15% is appropriate
Infill Pattern = Archimedean Chords
Print speed = Normal (Bambu Lab X1C)

Pretty much used default settings other than



APPLE DESK CART

chassis all final.stl

Design took couple weeks to resolve all the issues while printing.

The original size for 2x2 is 220x220x222.5 mm.
The original size for 2x1 is 110x220x222.5 mm.

You should be able to print the model without any problem with the settings I provided :)

Please support me by following on Social Media platforms:
https://www.instagram.com/tahaedilgen/
https://www.tiktok.com/tahaedilgen/
https://www.twitter.com/tahaedilgen/

The downloadable files for these models are for personal use only. Commercial use, distribution or modification of the models can be authorized via Patreon: https://www.patreon.com/tahaiswilling

3D PRINTING SETTINGS
NO SUPPORTS NEEDED!

If you don't want to read, here is a video: https://youtu.be/Y54NfjoCQK8

The model has built-in supports for better bridge print. You can remove them afterwards very easily!

SPECIAL INSTRUCTIONS TO REMOVE THE BUILT-IN SUPPORTS:

The supports inside the drawer must be collapsed first.
Then bump the drawer from the bottom with a Ruler in order to break the bonding between drawer skids and outer shell. 
After making sure you removed all bonding between drawer and outer shell, try to pull the drawer outside.
If it is not coming, you couldn't push the ruler all the way, you need to push the ruler all the way and try again!
Lastly, you can remove the bottom supports at the bottom L-E-G-O part with a Flush Cutter very easily :)

Print settings:
- Supports: NO
- Nozzle: 0.4 mm
- Layer height: 0.2 mm
- Speed: Normal (Bambu Lab X1-Carbon)
- Slow down for overhangs: False
- Bridge speed: 100 mm/s
- Bridge direction: 180 degrees
- Wall loops: 2
- Top shell layers: 3
- Bottom shell layers: 2
- Infill rate: 5%
- Infill type: Grid
- Brim: Yes (inner brim only)
- Brim width: 5 mm

This print takes about 1 day and 1 spool to finish :)
PLEASE NOTE: If you want to increase the Quality and Strength of the print, you can increase the infill rate but then 1 spool will not be sufficient! 

These settings should print you the model with NO Supports. There might be a few loose fibers under the drawer and L-E-G-O part, you can either leave as is or clean easily with Pliers & Utility knife if it is too bad ;)

Timelapse of the print: https://youtu.be/VfKSzFoOtYg

L-E-G-O DRAWER (FLEXI)

2x2 drawer v14.stl

I am not sure if it is Montessori toy but enjoy while I am still trying to figure things out :)

Tried 20% wood PLA filaments for this toy and it looks great, tell me what you think!

Please support me by following on Social Media platforms:
https://www.instagram.com/tahaedilgen/
https://www.tiktok.com/tahaedilgen/
https://www.twitter.com/tahaedilgen/

The downloadable files for these models are for personal use only. Commercial use, distribution or modification of the models can be authorized via Patreon: https://www.patreon.com/tahaiswilling

3D PRINTING SETTINGS
NO SUPPORTS NEEDED for the model, the Model has built-in supports

Suggested settings with Bambulab X1C

Slow down for overhangs: False
Bridge speed: 50 mm/s
Bridge direction: 180 degrees
Infill Density: 15%
Infill Pattern: Grid
Brim: NO

Other settings can stay default



FLEXI TOY SHEEP

I am not sure if it is Montessori toy but enjoy while I am still trying to figure things out :)

Video about the Montessori topic: https://youtu.be/rdmu_aFgOdc

Tried 20% wood PLA filaments for this toy and it looks great, tell me what you think!

Please support me by following on Social Media platforms:
https://www.instagram.com/tahaedilgen/
https://www.tiktok.com/tahaedilgen/
https://www.twitter.com/tahaedilgen/

The downloadable files for these models are for personal use only. Commercial use, distribution or modification of the models can be authorized via Patreon: https://www.patreon.com/tahaiswilling

3D PRINTING SETTINGS
NO SUPPORTS NEEDED for the regular panda, the Model has built-in supports

SUPPORTS NEEDED for the panda with wheels, please see images for the support setup in slicer

Suggested settings with Bambulab X1C

Slow down for overhangs: False
Bridge speed: 50 mm/s
Bridge direction: 180 degrees
Infill Density: 15%
Infill Pattern: Grid
Brim: NO

Other settings can stay default

FLEXI TOY PANDA

montessori toy panda v8.stl

This cute robot with cactuses in front of it is small pen holder for your desk :)

You just need to glue the arms, eyes, ears and cactuses into the slots in respective places. You also need to remove the supports in head, base and big cactus parts.

The model DOES require supports in "head", "base" and "big cactus" parts.

Please support me by following on Social Media platforms:
https://www.instagram.com/tahaedilgen/
https://www.tiktok.com/tahaedilgen/
https://www.twitter.com/tahaedilgen/

The downloadable files for these models are for personal use only. Commercial use, distribution or modification of the models can be authorized via Patreon: https://www.patreon.com/tahaiswilling

CUTE ROBOT PEN HOLDER

head.stl

This SAD Panda Faced large pen holder is warm friend for your desk :)

You just need to glue the black parts into the slots in respective places.

The model does NOT require any supports in.

Please support me by following on Social Media platforms:
https://www.instagram.com/tahaedilgen/
https://www.tiktok.com/tahaedilgen/
https://www.twitter.com/tahaedilgen/

The downloadable files for these models are for personal use only. Commercial use, distribution or modification of the models can be authorized via Patreon: https://www.patreon.com/tahaiswilling

Taha Edilgen

Achievements

Seedling

Debutant

Pinned models

FLEXI TOY PANDA

L-E-G-O DRAWER (FLEXI)

Edilgen Blocks

Edilgen Blocks

APPLE DESK CART

L-E-G-O DRAWER (FLEXI)

FLEXI TOY SHEEP

FLEXI TOY PANDA

CUTE ROBOT PEN HOLDER

SAD PANDA PEN HOLDER