This is a 0.2mm Bed Level test print.  Use this to test your bed level and make adjustments.

Be sure to Lube the Rods on your printer before you Insert the sd card into the Slot.  You want the up and down motion to be as smooth as possible...  ;)

First Layer Porn Bed Level Test

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3488324.

UPDATE: LATEST VERSION IS MORE ROBUST Also added new versions for NineBot EUC's.

This is a small, simple print that helps in a big way. Just double sided tape one of these on each pedal and make your life easier.

I mean, why not keep from bending over when you are riding a device that keeps you from having to walk. Total Laziness! ;)

I printed these at 25% infill with 4 top/bottom/side layers. I printed in ABS, but I would imagine PLA will hold up just as well. Updated version prints well standing up.

Watch Videos:

<iframe width="560" height="315" src="https://www.youtube.com/embed/U2RIX4E-Bbc?controls=0" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>

<iframe width="560" height="315" src="https://www.youtube.com/embed/PsRDXe1jOxM?controls=0" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>

Electric Unicycle Pedal Pushers

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2558998.

What is this for? https://youtu.be/eJxnd2Ne9uo

This is a Remix of EUGYS's fender.  I just added the Parking Stand Feature, and I'm going to be uploading different variants of that in this same post to make it easier for me and for you.

The fenders will need supports due to how the Parking Stand parts are in the air.

Darth Vader
https://youtu.be/n7Qd1wwvaS4

Superman
https://youtu.be/KeEppl5QzYQ

Holes
https://youtu.be/OqoqvNlbgOk

Batman and Spider Web
https://youtu.be/oV5Kb_7t60k

Time Lapse
https://youtu.be/8PoedQ-_77U

GotWay MSuper V3 Parking Fender Version 2 + Variants!

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2555227.

What is this for? https://youtu.be/eJxnd2Ne9uo

Using EUGUY's desing, I've started to try cutout designs.  Here's my first one.  I have not printed this yet, but it should print fine with some supports in the logo.  The fender itself does not require supports to print.

https://youtu.be/do6ZTVBE5sI

Time Lapse of my other fender being printed. 
https://youtu.be/8PoedQ-_77U

Superman Fender for GotWay MSuper V3 (Fit's all V3 Variants)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2670658.

<big><big>UPDATE #2: Added Easy Print Version</big></big> Thanks to foxgloveross for the idea!

<big><big>UPDATE: Just added a few different versions!</big></big>
Sorry about the artifacts. 3D Builder kept adding them.

So, after searching everywhere for the perfect K-Cup Dispenser, I stumbled upon curiosgreg's version. It's almost perfect, except I buy 12 packs of coffee, or even the large cases from Costco. So, I decided to remix curiousgreg's version to hold 12 cups.

Hope you like it. Keep in mind, this took almost 2 days to print with supports. Maybe you can find a way to print without as many supports as I did.

https://youtu.be/xjQ8W2KDPxQ

https://youtu.be/q3yCB7uyE9Y

K-Cup Dispenser (12 Cup Version) Now Includes Variants

K_Cup_Dispensor_12_Cup.stl

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3230675.

What is this for? https://youtu.be/eJxnd2Ne9uo

EDIT: Just added a stretched version of the fender to hopefully help with clearance. I have not been able to test this model, so try at your own risk.

Finally! I've finished the Parking fender for the GotWay MSuper X. This is the same fender as my Standard MSuper X fender, except I added the parking feature to it. You can see how that works on the MSuper V3 here:

https://youtu.be/eJxnd2Ne9uo

When you install this fender, you compress the two sides and get the clips into the wheel well. It will be hard to compress with the parking feature built in. Be sure to slide it all the way up against the top clips, and then the lower clips will snap into place above the LED cases. 

IMPORTANT: After you've gotten it to click into place above the LED housings, be sure to press outwards on the fender to be sure the lower clips are as far outward as possible. This will make sure the tire does not rub. If your tire is rubbing, then check that the fender is all the way up and out.

NOTICE: If you'd like the NON Parking Stand version of this fender, please see here: https://www.thingiverse.com/thing:3230717

GotWay MSuper X Parking Fender MSX (Parking Stand Fender)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3230717.

What is this for? https://youtu.be/PyuSpqig23M

EDIT: Just added a stretched version of the fender to hopefully help with clearance. I have not been able to test this model, so try at your own risk.

Finally getting around to posting my MSuper X fender (Mudguard). This is a remix from EUCGUY's fender for the MSuper V3. I had to modify the design and make new lower clips, but the upper clips I used directly from his design because they work so well.

When you install, compress it from the sides at the lower clips. Tuck the upper clips into place, then the lower clips. The fender must be slid all the way up against the upper clips so that the lower clips will click into place above the LED housings. 

IMPORTANT: After you've gotten it to click into place above the LED housings, be sure to press outwards on the fender to be sure the lower clips are as far outward as possible. This will make sure the tire does not rub. If your tire is rubbing, then check that the fender is all the way up and out.

NOTICE: If you would like the Parking Stand version of this fender, please see here: https://www.thingiverse.com/thing:3230675

GotWay MSuper X Fender Mudguard MSX (Includes Variants)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2494433.

75% Infill
0.100 Layer Height
Supports only under the Parking Stand portion

This was made from Tilmann's Original Fender Design.  I simply added the Parking Structures.
It took nearly 16 hours to print, so you may want to try 0.200.  I also don't know yet how strong this will be.   You may want to try 100% infill?  I will probably have to break this one to find how sturdy it is, but I'm going to use it for a while fist since it took so long to print.

https://youtu.be/eJxnd2Ne9uo
https://youtu.be/0pV1t23UhvQ
https://youtu.be/BN5GnqW1oXY
https://youtu.be/UJuOiGbf9wk
https://youtu.be/8PoedQ-_77U

Disclaimer:  As the sport of EUC can be very dangerous, please use this design at your own risk.

Parking Fender for GotWay MSuper V3

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2978030.

JUST ADDED NEW VERSION FOR X-ACTO KNIFE.

This is a simple Tool Holder Insert for the Toxic Waste Cups. I LOVE the Toxic Waste Cups by somethingc found at the link below. I used to toss my tools into them, but I decided to organize the tools a bit. So, I designed an insert that holds the tools in place. I hope you like it! This holds the basic tools that come with the CR-10 Printer when new. The other tools are held on the control box with a different tool holder. I've also included the original 3mf file in case you want to modify it for different tools.

Link to Toxic Waste Cup: https://www.thingiverse.com/thing:1645540

Link to other Tool Holder: https://www.thingiverse.com/thing:2253349

Toxic Waste Cup Tool Insert - 2 Versions

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4574326.

Just a very simple Chain Slider to protect the frame on a 1987 Yamaha TW200.  I would assume it would fit other years also, but I don't know that for sure.

This lasted about 6 months that I know of.  It was still in good shape when I traded the bike.  I used PETG because that's what I had.

I don't have the bike anymore, so I cannot take any more photos of it, but here's a video that should help.

https://youtu.be/YK-o4ATFutc

Your mileage may vary...

TW200 Chain Frame Slide

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2769606.

This is a Re-Mix Mixup of Devin Montes' Extruder Knob and graham01's Extruder Cover.
Devin's knob is here: https://www.myminifactory.com/object/manual-filament-feeder-knob-mod-for-cr-10-and-other-bowden-3d-printers-52492

I simply used the knob to cut a hole in the cover, and this is the perfect combo for me.

Not only does the knob help to load and unload the filament, but it also gives you a visual cue when the filament is moving. The cover keeps all dust and dirt out of the Extruder and helps to hold the wires in place.

I printed both at 0.2 and no supports.

NOTICE: Be sure to install the small piece of Bowden Tube as shown in the last 4 photos. That will make it so you can print Flexible Filaments without issues. And it also helps with normal filaments.

NOTICE: It has been commented below that this may not fit the newer CR-10 with a black extruder. Please verify before printing.

Extruder Cover and Knob Remix / Re-Package

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4918496.

I modified Oskar_B's Bosch Sensor Holder because I have an Xduro and the Fat Rear 2.8" Tire caused the magnet to hit the sensor using Oskar_B's design.  In my case, the surface that the screw goes through broke off.  So I used Oskar's design and added my own mounting surface that recesses the sensor a bit so the magnet clears the sensor.  It works perfectly.  

Printing:

I printed in PLA Carbon Fiber at 100% infill for strength.  I printed using supports with the hollow cylinder facing down.

You will need two Zip Ties to attach the sensor to the mount.  I also trimmed the sensor to be flat on the end so it looks cleaner.  I used side cutters to remove the extra material, see photos.

Bosch Performance Line CX Haibike Ebike Sensor Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3471143.

My Stanley FatMax Car Jumper/Air Compressor jumped around too much, so I decided to design and print in TPU these feet.  It's much quieter, and does not move around nearly as much.

YES, I DO have a German Shepherd, thus the fur everywhere!!!!

Stanley FatMax Cushioned Feet

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3684004.

WORK IN PROGRESS!!!

This is a test file of my Minimal Fender.  It will likely need a little double sided tape or silicon or something to hold it in place.  I may get back to adjusting it so it holds better.  

I also have NOT tested if it holds back the water spray.

I printed it in TPU for this test.

Video here:
https://youtu.be/ilH_MZJU6Mk

MSuper V3 and V3S+ Minimal Fender (Work in Progress)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2890920.

UPDATED VERSION!  Now with lip to grab onto.

The charge port on my GotWay MSuper Electric Unicycle finally tore in half, so I made this to replace it.  I simply pressed the retainer ring onto the charge port and then pressed the cap on.  Easy Peasy.

This should work on any charge port that is 14mm.

I printed it in TPU material so it was flexible enough to bend and to flex onto the port.

Charge Port Cap for GotWay and Other Electric Vehicles

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4577126.

Just a quick TW Key Ring Key Chain for the Yamaha TW200

TW200 Key Ring

Just a guy that likes to print goofy stuff.  I also make things I need, and do a little YouTube.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

SuperSport1966