Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3272032.

Remix of DavidDotShaw's very cute fridge magnet. Made the magnet a little longer (our dog is a bit longer!) and changed the magnet holes to suit dual 6.5mm magnets instead of the larger 10mm magnet in the original file. Also included the Fusion 360 source. 

Dog Fridge Magnet

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4923359.

The lower hook for winding the cord on my Shark Rotator vacuum (Model UV560 31, according to the label) broke, leaving the cord a tangled mess. This is a rough replacement for the original part. It's not a perfect fit - the contours on the vacuum are pretty challenging to model accurately - but it fits and works. I also hope that it's a bit stronger than the original.

STEP file provided in case you need to make adjustments for your specific printer or vacuum.

Lower cord winder hook for Shark Rotator vacuum

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4691067.

I had a lot of trouble finding a fan duct model which worked on the late 2018 version of the Geeetech A10 - all the versions I found were too wide and didn't work. This is a reimplementation that's close to the original, with some modifications for easier printing.

Geeetech A10 (Late 2018) Part Cooling Duct

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3315625.

This is a simple outdoor housing for the Monoprice 4-in-One multisensor. It provides a small amount of additional protection over the stock mount by putting a small "roof" around the sensor and by adding drain holes at the bottom for moisture to escape from. 

I can't guarantee that your sensor will survive being used in this, but it'll be interesting to find out!

Let me know how it goes for you.

Monoprice Multi Sensor Outdoor Housing

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3301119.

A wall mount for the Lutron Caseta hub! Clips over the whole hub. There are four holes, but I'm only using two myself - it was mostly just more convenient to make 4 holes than 2.

Lutron Caseta Hub Wall Bracket

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3352549.

The Geeetech A10 changed in late 2018 with the release of the A10M, moving the LCD's ribbon cable connector over a few mm. I expect this should work on the A10M as well, but can't promise anything. 

Hope it helps!

Geeetech A10 Back LCD Cover (Late 2018 Model)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3271527.

Loved the original idea from Moksiu, but the STL wasn't printable through Cura. I redesigned the model from stratch to use two larger magnets (6.5mm diameter, 1.6mm thick), so this one is substantially bigger than the original, using about 10g plastic to print.

I rebuilt this in Fusion 360, primarily by eyeballing the original. I've included the parametric file to play with - you can adjust the magnet size in the parameters section to scale the entire design to fit a particular magnet size. I didn't carefully test this, and I'm sure it'll take a lot of adjustment to get it just right for your purposes, but it's available for you should you want it.

UPDATE: Added a less-angled 15 degree version to the files.

Bigger Ninja Fridge Magnet

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3371611.

The stock game comes with only one short ruler! With this, you can print off one for each player.

The ruler is a little longer than the stock ruler at 12 units long (up from 10) and features raised indicators on the commonly-used multiples of three. Because it's symmetrical, it can be used either direction, and the straight side can be used as a ruler.

Treasure Island Small Ruler

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3370248.

A replacement ruler for the stock game! Instead of a clear ruler, this is a slimmer ruler. There are raised markers for 3 and 6, commonly used distances in the games. In addition, the bottom of the ruler can be placed right against the standee without removing it from the board, and the built in marker slot makes it easier to make a line.

Treasure Island (Board Game) Custom Long Ruler

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

Sparkinium