This is a revision of [this design](https://www.printables.com/model/462055) on Pritables, but I don't have an account over there and I'm not about to make one. Kieran's design was for a 12oz can, my revision just adds some length to accommodate standard US 16oz beer and energy drink cans.

Why do we bike? To have a beer at the end, that's why. But isn't it a pain to not have a designated holder for your beers for quick access? We should be able to enjoy a warm, shaken up can of 9% double IPA (locally sourced) at a moment's notice. 

Introducing the bike mount can clip, 16oz edition. This is designed to attach to any standard spacing water bottle cage mount on a bicycle, but as shown in the pictures it can also be attached to the fork.

I would recommend printing on its side, no support material, 30% infill. I tried printing on its back on the first attempt and the layer line placement caused the lower tab to snap right off.

Bike Can Clip - 16oz

Bike Can Clip - 16oz v0.stl

This is a 2x1 Gridfinity baseplate designed to hang on the side of an aquarium. I wanted an easy solution to hold my fish food so I adapted a simple 2x1 baseplate, so this will interface with any Grifinity bin/holder than can fit in that footprint. The clearance for the hanger is 8mm, so any glass 8mm or thicker will be unlikely to fit. 

This most recent version is designed to no longer need any support material, but this results in it being shorter. I may make another further revision that is "taller" that has a lower center of mass when hanging over the side so the the Gridfinity bins don't sit taller than the edge of the tank. 

Aquarium Hanging Gridfinity Baseplate - 2x1

Gridfinity 2x1 Baseplate v2.stl

I saw this product on Amazon (see pictures) and really liked the design and thought it would be easy enough to replicate. This is a fish hideout for the corner of a fish tank. The high lips on the opening allow it to be buried under the substrate and the open sides allow visibility if placed against the front of the tank. This 3x3 model can be scaled to accommodate tiny shrimpies or shy loaches.

Be sure to print at 100% infill if you want it to sink! Also, support material is inevitable on this one, sorry.

Corner Fish Hide

Corner Fish Hide v1.stl

This is still very much untested, print at your own discretion.

I wanted to make some sort of tile dispenser that I could load up randomly at the beginning of the game and then just simply pull the next served-up tile. My previous method for pulling random tiles was to reach my hand into a cardboard box full of tiles, but I thought it was too obvious what tiles I was touching when it came to the physical differences between regular path tiles and the more complex effect tiles. 

Based on some testing it seems like the tiles have to be on a pretty steep slope for them to slide down freely, so the current design only has one rotation in order to keep the slope as steep as possible. I had some dead space in the middle of the design so I integrated a ball dispenser in there that feeds into the same opening that the tiles exit from. I'll be printing this soon and reporting my results.

Hextraction Tile Hopper Dispenser with Ball Storage

Hextraction Tile Hopper v2 v3.stl

A quick and dirty vertical hopper design for Hextraction game tiles. The idea is to load this randomly and have the tiles more easily available to draw from in game. I have concern with how will it will actually work, but I wanted to put it out to share in the meantime.

Hextraction Tile Hopper

In my city there are these open pipes/holes in the sidewalk from old disused water and gas lines. I wanted to make a Geocache container that would sit in these holes, lay flush with the sidewalk, and be largely unnoticeable to the laymen. This is a very specific design for my use case, but maybe other folks will find it useful with a quick remix.

In-Ground Geocache Container

Ground Cache Base v6.stl

Tired of holding your balls in a sack? Like an animal? Or worse! In your bare hands? Introducing the Hextraction Tile Ball Holder!

This ball holder utilities the form factor of a standard game tile for no other purpose than aesthetic consistency. It is not intended to be used as a playable game piece, but it will fit on the game board all the same. This design holds about 50+ balls with a little ball balcony for easy ball grabbing. A ballcony!

This newest version has been redesigned to no longer need any support material. 

Hextraction Tile Ball Holder

Tired of holding your balls in a sack? Like an animal? Or worse! In your bare hands? Introducing the Hextraction Tile Ball Holder!

This ball holder utilities the form factor of a standard game tile for no other purpose than aesthetic consistency. It is not intended to be used as a playable game piece, but it will fit on the game board all the same. This design holds about 25 balls with a little ball balcony for easy ball grabbing. Balls!

Please print this this with support material for areas touching the buildplate (but not everywhere or you will fill up the spiral), I made no considerations for the little ballcony in my design.

Every summer my house gets hot, and my PC just made it worse. I wanted a way to collect the exhaust heat from the case and port it directly out the nearby window, and I wanted to not take up too much space doing it. This simple design covers the two fan vents on the top of the case, as well as the upper rear fan and the graphics card exhaust. It has a 4" diameter output designed to interface with standard dryer ventalation hose. Holes have been modeled into the top to allow for the use of 6x2mm magnets. The bottom of the rear portion has been purposely left open to allow the cables to run out. I have provided a full version of this model, as well as a 4 segment version that will fit on a 220mm square bed. For reference, this was designed to interface specifically with my case, which is a Corsair Vengeance C70.

PC Case Heat Collector

PC Heat Collector v3.stl

PC Heat Collector - Part 1.stl

PC Heat Collector - Part 2.stl

PC Heat Collector - Part 3.stl

PC Heat Collector - Part 4.stl

PC Heat Collector - Part 5.stl

This is a 5x1x3 Gridfinity bin designed to hold any tubular item up to 16mm in diameter and 208mm in length and still be stackable. I designed this with the Xaomi Wowstick and its tubular bit holders in mind as I couldn't find other designs this compact, but it will work with any sort of bulky designer pen or paint markers that exceed standard Sharpie dimensions. Accommodating a 16mm diameter item in 21mm space was no small task, and as such the channels overlap with the Gridfinity base a tiny bit causing some small holes in the bottom of the print, but rest assured as stackability is still maintained.

EDIT: For whatever reason, the model looks strangely smoothed-out in the preview, but if you download and open in your slicer software it looks just fine. 

Gridfinity Wowstick,Marker Stackable Bin - 5x1x3

This is a 5x1x3 Gridfinity bin designed to hold any tubular item up to 16mm in diameter and 208mm in length and still be stackable. I designed this with the Xaomi Wowstick and its tubular bit holders in mind as I couldn't find other designs this compact, but it will work with any sort of bulky designer pen or paint markers that exceed standard Sharpie dimensions. Accommodating a 16mm diameter item in 21mm space was no small task, and as such the channels overlap with the Gridfinity base a tiny bit causing some small holes in the bottom of the print, but rest assured as stackability is still maintained.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Scoot3r

Achievements

Seedling

Novice Maker

Trailblazer

Up and Coming

Pinned models

Gridfinity Wowstick,Marker Stackable Bin - 5x1x3

Hextraction Tile Ball Holder

Bike Can Clip - 16oz

Bike Can Clip - 16oz

Aquarium Hanging Gridfinity Baseplate - 2x1

Corner Fish Hide

Hextraction Tile Hopper Dispenser with Ball Storage

Hextraction Tile Hopper

In-Ground Geocache Container

Hextraction Tile Ball Holder

PC Case Heat Collector

Gridfinity Wowstick,Marker Stackable Bin - 5x1x3