Modern and minimalistic Santa decoration, fun and stylish deco for this year's christmas season. All parts can be printed seperately, no need for MMU. The body of santa has a hole on the bottom to insert an electronic tealight, which will shine through the body and the face when using a translucent filament, creating a cosy look. Beard, tip and bottom of hat should be printed in fuzzy mode. 

**Fuzzy mode settings:**
Beard: contour, 0.4mm point distance, 0,2mm skin thickness
Hat tip and bottom: contour, 0.9mm point distance, 0,4mm skin thickness

**Assembly is straightforward and glue is not mandatory:** First slide the beard over the body, then insert the nose. After this step you take the bottom strip of the hat and break the printed seam/gap to allow it to flex open and snap into the body of the hat. After this is done you can insert the top ball of into the hat body and put the hat on top of your Santa Claus!

**If you want to support me or get commercial licenses you can join a patreon membership:** https://www.patreon.com/SabreDesign

**For one time support you can also buy me a coffee here: **https://buymeacoffee.com/sabredesign

**Check out more of my designs on my profile**

Christmas Santa decoration (tealight compatible)

Santa body.3mf

Angel with Child statue embodying the bond of a guardian angel and one of your loved ones in a minimalist and modern way.
The model is 130 mm tall and can be scaled up to your liking.

**If you want to support me or get commercial licenses you can join a patreon membership: **https://www.patreon.com/SabreDesign

**For one time support you can also buy me a coffe here: **https://buymeacoffee.com/sabredesign

**Check out more of my designs on my profile**

Guardian Angel with Child Statue

Angel (angel with child).3mf

Acorn autumn decoration. Available in large and small size, large is 150 mm tall and small 104 mm. The inside of the bottom is hollow to save on filament and to allow an electronic tea light to shine through when using translucent filaments. You will need a brim for the bottom part and supports for the top lid. Top lid should be printed in fuzzy mode (contour only) for a rougher textured look. 

**If you want to support me or get commercial licenses you can join a patreon membership: **https://www.patreon.com/SabreDesign

**For one time support you can also buy me a coffe here: **https://buymeacoffee.com/sabredesign

**Check out more of my designs on my profile**

Acorn container decoration (tealight compatible)

Acorn large bottom.3mf

Model kit of the famous Executor-class Super Star Destroyer from Star Wars episode V. Scale is roughly 1:100000. The model is 180mm long and the parts are straightforward and easy to assemble. Also added a stand to display the model in a stylish way.

Make sure your printplate is clean for optimal bed adhesion, since there are some small parts. Depending on your printer and filament the part tolerances may vary. The current model has been tuned on one of my Bambu P1S printers and the parts snap together nicely with the connecting pins. You can however use small amounts of glue to adhere the parts together.

**If you want to support me or get commercial licenses you can join a patreon membership:** https://www.patreon.com/SabreDesign
For one time support you can also buy me a coffe here: https://buymeacoffee.com/sabredesign
**Check out more of my designs on my profile:**

Super Star Destroyer Kit

Stand.3mf

Tall Pumpkin for halloween decoration. The model is 160 mm tall and 84mm wide. The body and stem are seperate bodies to make it easy to print in two colours, you can simply glue the stem into the pumpkin body.

The inside of the model is hollow to save on filament and to allow the tea light to shine through when using translucent filaments. You will need supports and a brim on the inside (these are included in the profiles).

Compatible with Bambulab LED Flame Tea Light Candle Set

**If you want to support me or get commercial licenses you can join a patreon membership: **https://www.patreon.com/SabreDesign

**For one time support you can also buy me a coffe here:** https://buymeacoffee.com/sabredesign

Halloween Pumpkin tall (tealight compatible)

Pumpkin tall body.3mf

A spooky ghost which fits an electronic tea light. Based on my original Ghozty design from last year. The model is 117 mm tall and 90 mm wide and is hollow with thin walls to save on filament and to allow the tea light to shine through when using translucent filaments. The model is oriented for optimal cooling in the included print profile which means there is no support needed.

Compatible with Bambulab LED Flame Tea Light Candle Set

**If you want to support me or get commercial licenses you can join a patreon membership: **https://www.patreon.com/SabreDesign

**For one time support you can also buy me a coffe here: **https://buymeacoffee.com/sabredesign

Check out more of my designs on my profile

Halloween Ghost

Ghost.3mf

Modern Halloween Pumpkin decoration. The model is 90 mm tall and 123mm wide, the standard model can be scaled up to your liking and scaled down to about 75% and still print fine and fit a standard electronic tea light. I also included files for printing the pumpkin body and stem in seperate colours, you can simply glue the stem into the body. Additionally I added a 60% scale single body pumpkin in case you want the model even smaller, this does not fit a tea light however. 

If you want you can also choose to print the one part model with two colours this will just require a lot of filament changes. 

The inside of the model is hollow to save on filament and to allow the tea light to shine through when using translucent filaments. You will need tree supports and a brim on the inside (these are included in the profiles). 

Compatible with Bambulab LED Flame Tea Light Candle Set

**If you want to support me or get commercial licenses you can join a patreon membership: https://www.patreon.com/SabreDesign**

**Check out more of my designs on my profile**

Halloween Pumpkin (tealight compatible)

Pumpkin.3mf

Modern and simplistic desk organizer for pens, tools, rulers and also paper cards and sticky notes/note pads. The flowing edge of the organizer will show the layer lines, so it is best to print at small layer height. Full size is 180 x 170 x120 mm, I also included a slightly smaller version scaled to 75% which is 137 x 130 x 90 mm.

**If you want to support me or get commercial licenses you can join a patreon membership: https://www.patreon.com/SabreDesign**
 
**Check out more of my designs on my profile**

Desk Organizer

Desk Organizer.3mf

Modern Sea Shell Vase based on a cockle/scallop shell, great addition for your home decoration. Should be printed with 3 perimeters to ensure the vase can hold water. Vase is 162 mm tall and 210 mm wide.

If you want to support me or get commercial licenses you can join a patreon membership: https://www.patreon.com/SabreDesign

Check out more of my designs on my profile

Sea Shell Vase

Sea Shell Vase.3mf

Small storage container for cremes, cosmetics, hair product etc. Great solution for traveling. Container has a 10ml volume. Thread is tuned for the corners of the lid to line up perfectly with the container when using bambu PLA filament, fit might slightly vary across filament brand and material.

If you want to support me or get commercial licenses you can join a patreon membership: https://www.patreon.com/SabreDesign

Check out more of my designs on my profile:

Small travel container

Mini travel lid.3mf

No supports needed. Scoop with curve to ensure material does not fall back out when pulling the scoop out. Inner volume of scoop is 1000ml.
Can be scaled to your liking, standard inner size is 74 x 74 mm. Angled opening part of the scoop should be placed on the printbed for optimal print quality. 

**If you want to support me or get commercial licenses you can join a patreon membership: https://www.patreon.com/SabreDesign

Check out more of my designs on my profile:**

Scoop no support

Scoop.3mf

Portable and handy Mini square with 100 mm scale for measuring stuff.
The dimensions of 100x60 mm it is perfect for checking or marking the angle of your parts while staying portable and easy to put in a pocket. To ensure your print is square it is important to calibrate the dynamic flow of your filament so the long edges are extruded as a proper straight line.
 

If you want to support me or get commercial licenses you can join a patreon membership: https://www.patreon.com/SabreDesign



Mini Square Tool

MiniSquare.3mf

After many months of testing I present the magnetic action exacto knife, great little tool for arts and crafts, opening boxes and also fun as a fidget toy (use responsible ;) )

You will need three 5x2mm magnets which will need to be glued into their dedicated holes, make sure you get the polarities correct when glueing them in so the bladeholder magnet sticks to both handle side magnets. Bladeholder and clip should be printed on a smooth surface/pei plate to ensure a smooth gliding action in the handle. Handle should be printed vertically/standing up with a large brim. 

The model is compatible with original X-ACTO nr11. blades and generic exacto blades. The generic blades have a 6x2mm slot in the base of the blade. The blade clip locks the blade into the bladeholder and will need some force to be fully pushed down, it is a tight fit which ensures the blade has a solid mounting point. When changing a blade the clip can break due to the tight fit so it is avised to print a few spare clips if you plan on changing often.

**If you want to support me or get commercial licenses you can join a patreon membership: https://www.patreon.com/SabreDesign**
 
**Check out more of my designs below on my profile**

Exacto knife

Exacto simple nr.11 Handle.3mf

Modern easter bunny decoration. The model is 110 mm tall, can be scaled up to your liking. The inside of the model is hollow to save on filament.

**If you want to support me or get commercial licenses you can join a patreon membership: **https://www.patreon.com/SabreDesign

Bunnies

Bunny.3mf

Modern Pen Holder stand to hold and display two pens in a stylish and modern way.

Easy print, can hold pens up to 150mm wide. Also added a small indent on the back to store another item.

**If you want to support me you can join a patreon membership: **https://www.patreon.com/SabreDesign

Pen Holder 

Pen Holder Stand.3mf

A modern fruit bowl, 228mm long, 253 mm wide and 66mm high

**If you want to support me or get a commercial license you can join a patreon membership: **https://www.patreon.com/SabreDesign

Modern Fruit Bowl

Fruit bowl.3mf

Recreate the spaceX starship launch with this desk stomp rocket. With a good push I have managed to get the rocket up to 3 meters, how high can you go? ;)

All parts printed in Bambu Basic PLA, when using different filament the tolerances may vary. 

**If you want to support me you can join a patreon membership: **https://www.patreon.com/SabreDesign


SabreDesign

Achievements

Seedling

Fan Favorite

Pinned models

Starship Stomp Rocket Launcher SpaceX

Modern Fruit Bowl

Pen Holder

Exacto knife

Christmas Santa decoration (tealight compatible)

Guardian Angel with Child Statue

Acorn container decoration (tealight compatible)

Super Star Destroyer Kit

Halloween Pumpkin tall (tealight compatible)

Halloween Ghost

Halloween Pumpkin (tealight compatible)

Desk Organizer

Sea Shell Vase

Small travel container

Scoop no support

Mini Square Tool

Exacto knife

Bunnies

Pen Holder

Modern Fruit Bowl

Starship Stomp Rocket Launcher SpaceX