Filament Motion Encoder

Wheel.stl

LH Fan Shield v4.stl

 LH Fan Mount v2.stl

Horiz Din Mount.stl

BQ BigTreeTech Octopus v1.1 horizontal DIN rail mount.

Frame Brace

Base Bracket LH.stl

SSR 90dg Din Rail Mount.stl

SSR 90° mount.
Mounts the SSR on its edge against the DIN rail.

Bed-Mos v1 Mount.stl

A mount for the large 67x88mm 30amp Mosfet to remove the high current from teh MCU board.

E3v2 Miscro Swiss Cooler

Back Plane.stl

Voron Afterburner ADXL Mount.stl

Magnetic mount for ADXL345 accelerometer. Requires 4/ 6mmØx2mm neodymium magnets and 2/ M2.6 SHCS self taping screws.

ADXL Mount v1.1.stl

Extractor Panel.stl

Passive chamber temps just from the heated bed were climbing over 45°C so I have added a printable extractor panel with a 6010 fan. 4x M4 SHCS and 4x M4 nuts. This can be mounted on either side of the lid frame replacing the small acrylic panel.

Electronic Case.stp

Lid.stl

Hinge.stl

Dbl Bracket.stl

Dbl Bracket RH.stl

Dbl Bracket LH.stl

Base Side Panel Clip1 x2.stl

Hinge Washer.stl

Base Front Panel Clip1 x1.stl

Base Side Panel Clip2 x2.stl

Single Rear Bracket.stl

Base Front Panel Clip2 x1.stl

Lid Shelf 1.stl

Lid Shelf 6.stl

LH Box Slide Filler.stl

TPU Washer.stl

Lid Shelf 5.stl

Panel Clips v1.stl

Lid Shelf 2.stl

Acrylic Panel Wedge.stl

Wedges acrylic panels against extrusion slot.

Lid Shelf 3.stl

Lid Shelf 4.stl

Corner Grommet TPU.stl

Work in progress. 
A cable surround grommit for cables to pass over the aluminium panel without snagging or wear. Print in TPU.

Corner Grommit TPU.stl

LH Power Lower 2.stl

2020 Extrusion Mounts.stl

Extrusion mounts creating the electronics case space.

Side Panel Grommet TPU.stl

Gromit for filling hole on side panel if not used.

Grommit TPU.stl

Panel Packer Mount.stl

Panel mount packer. Slides in between panel and into the slot of the 2020 extrusion.

Top Closure Packer.stl

Packer below rear cross member extrusion and the top closure part. 

RH Grill Upper.stl

LH Fan Upper.stl

RH Grill Lower.stl

Top Closure.stl

Base Closure RH.stl

Motor Surround RH.stl

RH Stepper motor surround. Note this part is intended to be used when using the corexy conversion.

Motor Surround LH.stl

LH Stepper motor surround. Note this part is intended to be used when using the corexy conversion.

Base Closure LH.stl

MW 5v PSU Mount Voron Remix.stl

Remix of the Voron Design teams DIN rail mount to support a Mean Well 5v PSU.

MW 24v PSU Mount x2 Voron Remix.stl

Remix of the Voron Design teams DIN rail mount to support a Mean Well 24v PSU.

SSR DIN Rail Mount Voron Remix.stl

Remix of the Voron Design teams DIN rail mount to support a typical SSR.

Mosfet Mount Voron Remix.stl

Remix of the Voron Design teams DIN rail mount to support the BTT Mosfet.

I have been in the architectural industry here in NZ for approximately 25 years and I thought I'd try my hand at 3d printing, designing my parts with Vectorworks.

Twitter: @printing_jc

RedWhere2020

Achievements

Sapling

Fan Favorite