Multiboard peg clip iLevar Electric Screwdriver holder that can hold it with the outer casing. My previous model was a remix of someone else's holder and it did not fit the iLevar case well (actually, it didn't even hold the outer case, only fit the inner one).

Thus I modeled a completely new one to fit it well.

This uses the Multiboard pegs. **Supports required for the pegs!**

No special settings required for this (other than supports), so print it however you'd like. I printed it with the following settings:

- PLA
- .2mm layer height
- Tree supports
- Aligned seam
- Wall generator: Arachne
- Order: inner-outer-inner
- 3 walls
- 15% infill (cross-hatch)
- No brim

iLevar Electric Screwdriver Multiboard Holder

iLevar Electric Screwdriver Multiboard Holder.stl

I made a remix of the homesolutions electric screw driver holder by mxkoty (https://makerworld.com/en/models/484040) into one that would work for the iLevar Electric Screwdriver. 

**This version does not fit the outer case. While it does fit the inner case it's not a great fit. As such, I've modeled a completely new holder completely from scratch. Search for the same name as this one.**

I'm not proficient with cad so it 'mostly' fits, but it does NOT fit with the outer case. Thus, it works, as shown in the image, with the inner case only.

Fits the Multiboard peg mounts.

Print with tree supports on the pegs.

Multiboard iLevar Electric Screwdriver Holder (old version)

Multiboard iLevar Electric Screwdriver Holder.stl

I wanted a more stable and secured way to build a shelving unit using the Multiboard system while leaving as much 'open' space on the sides. Thus, I spliced a 6x6 push-fit bracket and a 4x4 push-fit bracket together into this here thing.

This is made so I can put one Multiboard Plate on the bottom, and then on the top and bolt-lock them together.

You can find the 6x6 double bracket here: https://thangs.com/designer/Peter%20Krzyzek/3d-model/Multiboard%206x6%20Push-Fit%20Double%20Sided%20Bracket-1079038

Multiboard 6x4 Push-Fit Double Sided Bracket

Multiboard 6x4 Push-Fit Double Sided Bracket.stl

I wanted a more stable and secured way to build a shelving unit using the Multiboard system while leaving as much 'open' space on the sides. Thus, I spliced two 6x6 push-fit brackets together into this here thing.

This is two Multiboard 6x6 Push-fit Brackets merged into one. This is made so I can put one Multiboard Plate on the bottom, and then on the top and bolt-lock them together.

This takes approximately 2hours 20 minutes to print using HS PLA on a Bambu P1S. 

Multiboard 6x6 Push-Fit Double Sided Bracket

Multiboard 6x6 Push-Fit Double Sided Bracket.stl

This is a lazy remix of the Weller Solder Iron Holder for Honeybomb Wall ... but for the Multiboard!

Why 'lazy'? Because I don't know cad much so I have no idea how to properly remove the old plug from the 'round' part, so I just cut it straight and spliced the Multiboard pushfit in there.

NOTE: I have extended the Multiboard pushfit by ~5mm, so it is longer than a normal pushfit. This is so it sort of matches the original design (of the holder) better. 

Original model in printables: https://www.printables.com/model/369003

Weller Solder Iron Holder for Multiboard

Weller Solder Iron Holder for Multiboard.stl

This is the one Multiboard unit wider version of my 4x3 shelf. This is the 5x3 Multiboard Multigrid Baseplate Shelf. Note, this model DOES throw warning in the splicer. I am not proficient in CAD so I'm pretty sure I resized things weird which is why it complains BUT it does print just fine (for me at least).

This model is very wide and take up the full width on my P1S, thus something like a Bambu A1 mini will NOT be able to print this.

I was in need of a simple yet elegant shelf but with the support of the Multiboard Multigrid baseplate. Sadly, there were only small shelves as well as Multigrid baseplates. The shelves weren't the same size (small only) where as the baseplates only were themselves. Thus I spliced the two together.

PLA and PTEG seem to print this fine. Though the Carbon Fiber (-CF) filaments seem to have problems with the edge overhangs so I recommend avoiding those.



5x3 Multiboard Multigrid Baseplate Shelf

5x3 Multiboard Baseplate Shelf.stl

I was in need of a simple yet elegant shelf but with the support of the Multiboard Multigrid baseplate. Sadly, there were only small shelves as well as Multigrid baseplates. The shelves weren't the same size (small only) where as the baseplates only were themselves. Thus I spliced the two together.

Note: the slicer WILL complain about overhangs and/or missing maniforld edges. This 4x3 size usually doesn't show warnings. Though, it prints perfectly fine either way if you're printer and filament are well enough calibrated for bridges and overhands.

PLA and PTEG seem to print this fine. Though the Carbon Fiber (-CF) filaments seem to have problems with the edge overhangs so I recommend avoiding those.

4x3 Multiboard Multigrid Baseplate Shelf

4x3 Multiboard Baseplate Shelf.stl

This is the Blade Dispenser for the Bed Scraper XL (https://makerworld.com/en/models/422861) though remixed for the Multiboard.

This has a pushfit plug with a small thread hole, so you'll need a single snap to ... push fit it into and you have the option to screw something small into the back!

Multiboard Blade Dispenser for Bed Scraper XL - Small Thread

Multiboard Blade Dispenser for Bed Scraper XL - Small Thread.stl

This is the Blade Dispenser for the Bed Scraper XL (https://makerworld.com/en/models/422861) though remixed for the Multiboard.

This has a pushfit plug on it, so you'll need a single snap to ... push fit it into!

I've also included a PART which has a small thread hole inside of the pushfit plug.

Multiboard Blade Dispenser for Bed Scraper XL

Multiboard Blade Dispenser for Bed Scraper XL.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Peter Krzyzek

Achievements

Voyager

Seedling

Debutant