Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5775179.

This is a collection of mini-figure scale [weapons and shields from the middle ages](https://en.wikipedia.org/wiki/List_of_medieval_weapons) and fantasy. There is very little vertical curvature in these designs besides the handles. This makes the designs print out much more reliably then other minifigure-scale weapons. This collection includes two different sized swords, a war hammer, and a poleaxe. 

For a recurve bow check out [my previous design](https://www.thingiverse.com/thing:5451389). 

Important: These are scaled so that the handle is 3.3mm wide. The hand of a mini-figure is only 3mm wide. The reason I made it larger is that my printer (a Creality Ender 3 Pro) and other printers tend to print a bit smaller than the actual size. At 3.3 mm, it prints exactly 3mm for me. You may need to scale it differently for your printer.

Also Important: When printing you will need supports so that the handles are perfectly round. You will need rafts so that the designs adhere to the print bed. And you will want to print at the shortest layer height your printer can handle so you get as many layers as possible.  

Minfigure-Scale Medieval Weapons and Shields

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5540682.

This eight-sided die is inscribed with the elvish numerals for 1-8. The numerals come from a elvish script called [Tengwar](https://en.wikipedia.org/wiki/Tengwar). Tengwar was created by [J. R. R. Tolkien](https://en.wikipedia.org/wiki/J._R._R._Tolkien) for his "Lord of the Rings" book series.

Print at 200% (about 52mm) for more character detail.

Also, check out my [Six-Sided Elvish Dice](https://www.thingiverse.com/thing:5026385).

Eight-sided Elvish Dice

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5864477.

The front of these coins is inscribed with one of the elvish numerals for 1, 3, and 5. The numerals come from a elvish script called [Tengwar](https://en.wikipedia.org/wiki/Tengwar). Tengwar was created by [J. R. R. Tolkien](https://en.wikipedia.org/wiki/J._R._R._Tolkien) for his "Lord of the Rings" book series. The coins values are 1, 3, and 5 because these denominations are commonly used by board games.

The back of each coin is inscribed with a [Leaf of Lórien](https://lotr.fandom.com/wiki/Leaves_of_L%C3%B3rien). I wanted to add more Elvish writing to the coins, but they did not print well with the added details. So I kept things simple.

For more Elvish designs, check out my [Six-Sided Elvish Dice](https://www.thingiverse.com/thing:5026385) and [Eight-Sided Elvish Dice](https://www.thingiverse.com/thing:5540682).


Elven Coins

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5784582.

This piece allows you to give any mini-figure breasts. It slides onto a mini-figure's neck like a backpack or cape.

Mini-Figure Breasts

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5451389.

This is a mini-figure scale [recurve bow](https://en.wikipedia.org/wiki/Recurve_bow). 

Important: This bow is scaled so that the handle is 3.3mm wide. The hand of a mini-figure is only 3mm wide. The reason I made it larger is that my printer (a Creality Ender 3 Pro) and other printers tend to print a bit smaller than the actual size. At 3.3 mm, it prints exactly 3mm for me. You may need to scale it differently for your printer. 

Minifigure-Scale Recurve Bow

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5364657.

NOTE: THIS JUST ADDS ONE ADDITIONAL FILE. YOU WILL STILL NEED TO PRINT OUT THE ORIGINAL GLOVE.

SECOND NOTE: THIS IS SIZED TO FIT A GLOVE PRINTED AT 95%. THE ORIGINAL GLOVE IS PRETTY BIG AND MOST PEOPLE WERE SCALING IT TO 95%. 

Step 1: Buy "Submersible LED Lights" by SHYMERY on Amazon. It should cost $13 dollars for 10 of them. 

Step 2: Print the glove at 95% scale

Step 3: Print this file at 100% scale

Step 4: Combine the LED, this and the glove.They should all fit snug. If you need to, you can add some tape to make it tighter.

Done. You can turn on the center LED on by twisting it. 

Solderless Remix of the Iron Man Glove

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5377470.

The original model has two versions: one with a base and one without a base. I wanted to make a claw without a base. However, that version has an open and uneven bottom.So I decided to make my own version of the claw with a flat bottom that is properly closed.  

Thing-O-Saurus Claw wIth no base and a flat bottom

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5364340.

NOTE: THIS JUST ADDS TWO ADDITIONAL FILES. YOU WILL STILL NEED TO PRINT OUT THE ORIGINAL WEARABLE ARC REACTOR.

The original model this was remixed from can be found here: https://www.thingiverse.com/thing:32274

Step 1: Buy "El Wire 5 Pack, 9ft Neon Light with Battery Pack (Red, Blue, Pink, Green, White)" by Kalakila and "Submersible LED Lights" by SHYMERY on Amazon. They should cost $16 and $13 dollars respectively.   

Step 2: Print all the parts of "Wearable Arc Reactor" except for the Crystal and Ring1. You won't need those two parts. Important: Print Ring2 at 95% size. It needs to be a bit smaller to make it easy to twist.

OPTIONAL: Print this instead of the normal top piece: https://www.thingiverse.com/thing:5346928 This allow you to make the coils red instead of silver.

Step 3: Print the two LED holders from this design

Step 4: Assemble the wearable arc reactor like normal.

Step 5: Glue LED_Holder3 to Ring2. Remember Ring2 needs to be printed at 95%.

Step 6: Put both parts of the LED holder on one of the LED lights. They should fit just right. Add some tape if you need the fit to be a bit tighter.

Step 6: Put some glue on the bottom of the LED holder and pace it in the middle of the Arc Reactor. Take you time and center it as best as you can.

Step 7: Feed the EL Wire through the hole into the base. You may need to make the hole a bit bigger. Coil it around the inside of the base. You may need disassemble the wearable arc reactor to do this.  

Done. You can turn on the center LED on by twisting it. The EL wire has a button on the battery box.

Solderless Remix of Wearable Arc Reactor

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5363763.

NOTE: THIS REQUIRES THE TOP PIECE FROM THE ORIGINAL DESIGN THIS IS REMIXED FROM.

The original model this was remixed from can be found here: https://www.thingiverse.com/thing:39862

The original version of this light holder would not fit on my electric scooter because it was too wide. So I had too cut away some bits of the holder to make it slimmer in the middle.

Slimmed Down Bicycle or Scooter Flashlight Holder 

This is a remix of the cover piece (or top piece) of the Wearable Arc Reactor. This modification separates the cover piece into two parts. This allows you print or paint the cover piece using two different colors. To match the movie, the outer ring should be metallic silver and the inner rings should be metallic red.

Remix of: https://www.thingiverse.com/thing:32274

Two Part Cover for Wearable Arc Reactor

ChestPiece2.stl

This phone holder allows you to use you iPhone SE (Gen 2 or 3), iPhone 8  or iPhone 7 with a magnetic phone holder. Normally, you would just stick a metal plate to the back of the phone for the magnet to attract. However, attaching a metal plate to the back of the iPhone blocks the phone from wirelessly charging. The phone holder solves this problem. The metal plate can be attached to the back phone holder instead. Then you just slide the phone into the phone holder.

This holder is sized to fit this case: https://www.thingiverse.com/thing:4861842
If your case is a different size, then you will need to scale this file.

iPhone SE Holder for Magnetic Car Mounts 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4921059.

I added a base to the vermling raider.

Gloomhaven Jaws of the Lion Vermling Raider With Base

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4925678.

I added a base to the stone golem.

Gloomhaven Stone Golem with Base

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4931101.

I designed this shirt/belt clip to fit the Pittsburgh Precision Screwdriver sold by Harbor Freight:

https://www.harborfreight.com/hand-tools/screwdrivers-nutdrivers/33-piece-precision-screwdriver-set-93916.html

This screwdriver can fit up to 4 bits in the handle so I like to carry it with me.


Screwdriver Pocket Clip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4912710.

8/18/21 Edit: I updated the design with several small improvements.
 
I designed this case to hold my multi-tool and clip to my belt. Make sure that you measure your multi-tool and scale all three dimensions of the model before printing. You multi-tool may be a different size than mine! This is meant for use multi-tools that are v-shaped.

My multi-tool was about 55mm at widest end and 35 mm at the narrow end.

The full print with 20% infill used about 72g of filament. The print time is 10 hours and 30 minutes with 0.2mm layer height

I made the cover from duck-tape and velcro.

Multi-Tool Holder with Belt Clip

IMPORTANT: This particular design is sized to fit a compact pistol (Specifically, the Ruger EC9s). If you have a full sized pistol you may need to scale the design up slightly.  

Handgun Racking Assistance Tool

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4967753.

This a 3D printer design based on laser cutter design I made in 2016. This is a large design so I included a split version that you can glue together. 

Original description:

"A claw design based on wolverine.
I tried to make them as movie accurate as possible.

Because the hand is not as thick near the pinky, there are two files. One file has a narrower space for the hand than the other. You will need to cut two of the wide ones and one narrow for each hand.

Total size should be 11.75 inches."

Wolverine Claws

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5026385.

This six-sided die is inscribed with the elvish numerals for 1-6. The numerals come from a elvish script called [Tengwar](https://en.wikipedia.org/wiki/Tengwar). Tengwar was created by [J. R. R. Tolkien](https://en.wikipedia.org/wiki/J._R._R._Tolkien) for his "[Lord of the Rings](https://en.wikipedia.org/wiki/The_Lord_of_the_Rings)" book series.

I created this design because I thought my fellow fantasy nerds might like some elvish dice for board games and role-playing. If anyone is interested, I may make more elvish dice designs in the future.

Six-sided Elvish Dice

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4967721.

A remix of a Nerf to Picatinny rail adapter. This remix adds a slight downward angle to the rail that makes it easier to compensate for the drop of the dart.

Nerf to Picatinny Adapter With Downward Angle

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4935582.

I designed this pouch to hold spare  handgun magazines. It will fit one single-stack 9mm magazine. I tested with a Ruger EC9S magazine. It can be placed inside or outside of the waistband.

There is a little bit of extra space between the magazine and the case. If you want some friction between the two you could add some tape to the inside wall of the case. 

9mm Magazine Carry Pouch

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4935046.

This remix adds another slot to this design. That slot allows a piece of velcro to loop through the knife holder. This allows the knife to be strapped to your leg or arm.

This needs to be resized to fit your knife. My dimensions were: X 10.4mm, Y 119mm, and Z 43.6mm. At this size, a 2 inch piece of velcro would fit through the strap slot. 

Print vertically (like the spine of the knife is resting on the bed and the edge is facing up) and don't use any supports.


Parametric Knife Sheath With Strap Slot

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4935998.

I bought a Sabre Red Pepper Spray Keychain, but I decided I would rather have something with a belt clip. That way I can conceal it inside my waistband. So I made this belt clip and glued it on to the side of the pepperspray. 

Pepperspray Belt Clip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4931962.

This is printed from flexible TPU then glued to the bottom of the stand. It makes it much more grippy.

Kindle Stand Grip

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

PetSven

Achievements

Seedling

Debutant