Sturdy 3 bag handle for one trip grocery runs.

**Print Recommendations**

Print Material: PLA or PETG

Infill Percent: 25%

Perimeters: 3

Supports: NONE

Carrying Handle for Grocery Bags

A formidable match for any post meal mess (yes, even that pan you've been soaking).

**Print Recommendations**

Print Material: PLA

Infill Percent: 25%

Perimeters: 3 

Supports: NONE

Dish Scraper

This is print in place model with integrated hinge that snaps closed. Fits cables up to 4mm thick.

**Print Recommendations**

Print material: PLA

Infill Percent: 15% 

Layer Height: .15 (a layer height greater than .15 will not work well since this model requires a very precise snap fit)

Perimeters: 2

Supports: NONE



Cable Clip

A study under-desk headphone mount to preserve that precious desk space.

This print requires a strong double sided tape to secure it underneath a desk. See Amazon link below for recommended tape.

**Print Recommendations**

Print Material: PLA (anything with high rigidity will do just fine)

Layer Height: .2

Infill Percent: 20% 

Perimeters: 3

Print Orientation: Side should be placed against the build plate (see Prusa Slicer file for orientation)

Supports: NONE 

 

Assembly

Add a strip of double sided tape to the straight portion of the headphone mount (see last photo for placement). 

Tape Required

Amazon Link to 3M VHB Tape https://a.co/d/aACaiWk

Headphone Mount (Under Desk)

Converts your Magsafe Charger into a dedicated charging station. Ideal for desks and bedside tables.

This print requires double sided tape. See Amazon link below for adhesive which doesn't leave residue. Folded over duct tape will work just fine if damaging the underlying surface is not a concern.

Fits only the official Apple Magsafe charger.


**Print Recommendations**

Print Material: PLA 

Infill Percent: 15%

Layer Height: .2

Perimeters: 2

Supports: NONE

Print orientation: Place the dock with the base against the build plate (see Prusa Slicer file for reference.)

 

Double Sided Tape Required

Amazon Link to 3M .4 inch double sided tape https://a.co/d/3n44GFr

This adhesive twists off easily and doesn't leave residue. See last photo for recommended amount and placement.

Mount for Apple Magsafe Charger

Symmetrical belt hanger designed to hook over curtain rods.

**Print Recommendations**

Print Material: PLA (anything with high rigidity will do just fine)

Infill Percent: 20% (this will easily hold belts and hangers)

Supports: NONE (give those snips a rest)

Belt Hanger

Premium tier gives you access to ALL exclusive models so you can print all the things in all your favorite colors. If you're here you must have a place in your heart for functional, minimalist designs and for that I salute you.

New Premium models are released each month. Why? Because optimization is a journey, not a destination.

Thank you for your support!

Nominal Brand Premium

Horizontal, minimalist, and subtle (unless you print it in bright red of course).

This design is for the Standard PS5 version with disk. Print 2 long springs and 2 short springs.  

Double sided tape is required. See Amazon link below for adhesive which doesn't leave residue, but any double sided tape should work just fine. 

**Print Recommendations**

Print Material: PETG (this design relies on the semi flexible properties of PETG)

Infill Percent: 25%

Perimeters: 3

Layer Height: .3 

Supports: NONE

Print orientation: Place each spring sideways against the build plate (refer to Prusa Slicer file for reference)

Assembly:

Attach double sided tape to each of the 4 springs. Place the 2 short springs near the base of the console and the 2 longer springs near the top (see photos for reference). 

Double Sided Tape Required

Amazon Link to 3M .4 inch double sided tape https://a.co/d/3n44GFr

This adhesive twists off easily and doesn't leave residue.

PS5 Horizontal Stand (for disk version)

PS5 Stand Long Spring (2 Required).stl

PS5 Stand Short Spring (2 Required).stl

Preparing coffee should be as smooth as that first sip. This wall mount fits #4 coffee filters.

This print requires double sided tape. See Amazon link below for adhesive which doesn't leave residue.


**Recommendations**

Print Material: PLA 

Infill Percent: 15%

Perimeters: 2

Layer Height: .15 (higher layer heights work just fine, but layers become more visible)

Supports: NONE

Print orientation: Place the top surface agains the build plate (see Prusa Slicer .3mf file)

 
Double Sided Tape **Required**

Amazon Link to 3M .4 inch double sided tape https://a.co/d/3n44GFr

- This adhesive twists off easily and doesn't leave residue. See last photo for recommended amount and placement.

Coffee Filter Wall Mount (#4 filters)

Coffee Filter Wall Mount.stl

A 100% printable chip clip.

**Settings for printing the Spring:**

Print Material: PETG ONLY (this design relies on the semi flexible properties of PETG)

Infill Percent: 100% (this is a critical one)

Perimeters: 3

Layer Height: .2

Supports: NONE

Print orientation: Place the spring sideways against the build plate (refer to Prusa Slicer file for reference)

 

**Settings for printing the Upper and Lower plates:**

 
Print Material: PETG ONLY (this design relies on the semi flexible properties of PETG)

Infill Percent: 20% 

Perimeters: 3

Top Layers: 5

Bottom Layers: 5

Layer Height: .2

Supports: NONE (there will be some bridging but any cleanup will be minimal)

Color Change: The model as shown was printed with a color change starting on the 4th layer to create the white+black combo. Print the Upper and Lower together without the Spring and add a layer change to get this look. The Prusa Slicer .3mf file does NOT have this color change in it.

Print orientation: (See Prusa Slicer file)

 

**Assembly:**

Make sure the bridging on the Upper and Lower portions was clean. If not, remove any stringing to ensure the Spring fits in.

(watch the assembly YouTube video below, unless you prefer a small puzzle)

[Chip Clip Assembly Video - Nominal Brand](https://youtu.be/o8xPfmvPPIk?si=FY3AbtOOyNS5grX4)

Chip Clip

Chip Clip all parts (Prusa Slicer).3mf

Hang your Dyson attachments on any closet rod. Fits Dyson V7, V8, V10, V11, V12 and V15 attachments.

**Recommendations:**

Print material: PETG (This design relies on the semi flexible properties of PETG)

Make sure the PETG is dry for this print so post processing with a pen knife is avoided.
Infill Percent: 20% 

Layer Height: .2 (layer heights larger than .2mm will not work for this model and will affect how the parts fit together)

Perimeters: 3 

Print Orientation: (see Prusa Slicer file for orientation)

Supports: No supports for the loop portion. The cylinder portion requires supports under the exterior pins (see Prusa Slicer file which includes paint on supports)


**Assembly:**

Rotate the loop until it snaps onto the main cylinder. The loop is keyed so that in only fits on in one orientation. This ensures it does not pop off during regular use.

Closet Mount for Dyson Attachments

Mount for Dyson Attachments (Both Parts) Prusa Slicer.3mf

Minimalist, functional, and intuitive designs. 

Print away and let me know how it goes!

-Ben (product designer and Nominal Brand owner)

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Nominal Brand

Pinned models