A basic monitor stand. Measures 8"x8"x4.25" (200mmX200mmX105mm). Designed it to fit my 22" HP monitors at work, should work with other monitors.

Monitor_Stand.stl

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4664438.

I really liked the Vat Saver(https://www.thingiverse.com/thing:4494475) for when I was working on the vat, but once I got my second vat I wanted something that actually covered the FEP while I was storing it.  So I remixed the Vat Saver into the Vat Vault. I added a floor (2mm lower than the shelf so to not touch the FEP) and 5mm threaded holes to screw the vat down. I use https://www.thingiverse.com/thing:4585753 as the lid.  This is not intended to be a secure way to store a vat full of resin as it does not seal.  It may help with sloshing if you are moving it around.  The point of this is to protect the FEP on your spare vat while in storage.  

If the threads become an issue, I will likely install threaded inserts.  

Vat Vault

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4663584.

In my AM8 to BLV-AM8 upgrade I was looking to use a BMG clone that I had laying around for over a year. Most of the mounts I found were made to have the stock 30mm fan and/or had issues with the BLTouch hitting the part cooler.  I took the original(https://www.thingiverse.com/thing:4395234) and reworked the right fan mount to free up a few more mm of space so that this fan duct would fit in. (https://www.thingiverse.com/thing:3177327)  I also filleted many of the edges to make it a little more aesthetically pleasing to me.  Of course this is all for the awesome BLV mod.  https://www.thingiverse.com/thing:2567757

I used a spacer on the bltouch.  My BLtouch offset is:
Probe Offset X-30.00 Y-30.00 Z-3.30


PS I tried to properly list all the "remix" sources but thingiverse seems to be broken.  

BMG Mount Remix for BLV Mod

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4906422.

Just a quick set of signs for our matching trash and recycle bins. The Recycle does not look the grates do to a printing error on my part.  The printer turned off the heaters and cooled all the way off waiting on me to remember to change the filament. 

Bin Signs

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4650290.

Most of the cable clips for the link and power cables are for the elite strap.  I am still rocking the stock strap.  So I really liked this design better than any others I could find, so I took it into Fusion 360 and made the arms longer so it will work with the stock strap.  

Quest 2 Cable Clip Stock Strap

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4771351.

I wanted to mount my box of gloves to the underside of the Ikea Lack Table I use for my SLA Printer station.  None of the other glove box holders I found looked like what I wanted or it would not fit the box of gloves.  So I went into Fusion and made this up.  After the print was finished I realized that the tilt of the oval is the opposite angle of what's on the box, but it still works as the hole in the print was sized to be a little large.    

I mounted it using velcro strips.

Kirkland Nitrile Glove Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4933585.

I tried Buszmen's designs, but all of them were giving me to much drag on the filament and causing under extrusion.  With how my print station is set up, I have had good luck with the stock TPU grommet and oversize tube.  With that in mind, I used Buszmen's basic design and adjusted it so that could allow for the stock TPU grommet and attach via double sided tape.  So far, seems to work well.  I figure if it helped me it might help another.  

eSUN eBox Hygrometer

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4625400.

I am trying to keep my SLA setup to the footprint of an Ikea Lack Table.  To do this I need a better storage system for the tools I use.  I needed something small that could fit between the Printer and the Wash & Cure.  So I jumped into Fusion and drafted this up.  It is a bit sloppy but gets the job done.  I hope others find it helpful. 

SLA Tool Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4563884.

This is a Remix of just the Holder.  This holder is for the Creality LD-002R.  It works and gets the job done, but is not elegant. You need to slide the build plate onto the holder as you lower it.  As I get better with Fusion 360 I will try to make it better.  

V3 has a longer mount so that they build plate can clear the back end of the lid better.  I am still working on a threaded knob to lock it in place.  

This is a remix from:
https://www.thingiverse.com/thing:4193798
and
https://www.thingiverse.com/thing:4510900

Update 8.26.2020  I have uploaded a new version,  This version places the build plate a little further out so that it is easier to lower in.  I also added a hole for an m4 nut.  If you also print the m4 hand screw and add a m4 nut & bolt to it, it can lock the build plate in place.   

Creality LD-002R Platform Holder for Wash Station

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3955010.

Customized version of https://www.thingiverse.com/thing:2256087

Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=2256087



My Customized Molle Name Tag - Quinn

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

LadySapphy

Monitor_Stand.stl

Vat Vault

BMG Mount Remix for BLV Mod

Bin Signs

Quest 2 Cable Clip Stock Strap

Kirkland Nitrile Glove Holder

eSUN eBox Hygrometer

SLA Tool Holder

Creality LD-002R Platform Holder for Wash Station

My Customized Molle Name Tag - Quinn

Vat Vault