AMS Dryer V2 - Plug.stl

AMS Dryer V2 - Vented Hygrometer Mount.stl

AMS Dryer V2 - Jig.stl

Follow up to the initial AMS dryer mod. After developing the model further, I redesigned the ducting to suit the dryer and AMS a little bit better. No need for support as the only necessary ones are modeled in. 

I would recommend using PETG or ABS at least as the temps of the PolyDryer will warp the PLA. 

Poly Dryer 
https://us.polymaker.com/products/polydryer?aff=839



AMS Dryer V2 - Adapter.stl

AMS Dryer V2 - Duct.stl

Here is the map from GTA 4. I have the islands separated to allow for maximum display size when assembled. I also have the complete model if you would prefer to print just the single piece smaller. See the attached short for more context or the following video for even more context still

New (Old) GTA Map Leaked (From 2008) #3dprinteraccessories #3dprinted #3dprinterfilament #3dprinting
https://youtube.com/shorts/MExX051k-X4?feature=share

GTA 4 Map Wall Art

Complete Map.stl

Follow up revision to the initial AMS dryer. This ducting has a modified profile to suit the TPU adapter gasket plugs. 

No need for supports as the only necessary ones are modeled in. I would recommend this piece be printed in PETG or ABS/ASA to suit the heat of the PolyDryer.

The adapters, plugs, and vented hygrometer mount all need to be printed in TPU but walls, layer height, infill does not matter.

The jig can be printed in whatever material you desire as it is simply for lining up the center points of the holes for the front of the AMS to ensure the ducting lines up correctly when sitting on the PolyDryer.

See the updated video for reference.
https://youtu.be/3jE5Yd633tA

Original video for reference
https://youtu.be/81vPb-U9PIs

PolyDryer
https://us.polymaker.com/products/polydryer?aff=839


This is an easy addition to your AMS lite. This sits in the middle and clips on snug. You simply thread in some standard hydraulic connectors and install the piece. This allows you to print abrasives or flexibles using your AMS lite as the spool holder since the lite can't feed those filaments. 

Reference the KeoPrints video if you want clarification. This eliminates the need for an external spool holder or roller when printing TPU or CF-PLA on the A1M

https://youtube.com/shorts/CB9O5jykvdc?feature=share

AMS Lite Passthru.stl

This model has been revised and updated here
https://thangs.com/mythangs/file/1142209

Prototype air duct for use with PolyMaker PolyDryer and Bambu AMS. This allows you to use the AMS as an active dry box after you cut some holes to suit the ducting. See video for reference. I will be updating the model as I develop further. 

https://www.youtube.com/watch?v=81vPb-U9PIs

Recommended mouse ears but it should print easily with no supports or other consideration. I printed in PLA but am not sure of the long term viability just yet.

PolyDryer
https://us.polymaker.com/products/polydryer?aff=839

AMS Dryer - Duct-3.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

KeoPrints

Achievements

Seedling

Debutant

AMS Dryer V2 - Plug.stl

AMS Dryer V2 - Vented Hygrometer Mount.stl

AMS Dryer V2 - Jig.stl

AMS Dryer V2 - Adapter.stl

AMS Dryer V2 - Duct.stl

GTA 4 Map Wall Art

AMS Dryer V2 - Duct.stl

AMS Lite Passthru.stl

AMS Dryer - Duct-3.stl