As an active member of this Tier you are granted a **Commercial License** to sell physical prints (online or in-person) made from my Regular models. 

***No selling or distributing the 3D Files***

I also encourage you to collaborate with me by giving feedback on existing models and suggestions for new ones. I can't wait to see what we can do together. 

Regular Model- Commercial License

These files are for Personal Use Only. If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad

Move over boat, there is a new benchmark in town.

This robot is not only a fun print-in-place figure but it is also a very useful calibration tool.

The robot is designed with 17 functional joints with different orientations, couplings, and tolerances. The tolerances range from 0.2 - 0.5mm and allow you to test the minimum clearances your printer can produce and still achieve print-in-place movement.

Each limb is labeled with the tolerances of their joints and all other joints have a 0.3mm tolerance. It might take a little (just a little) bit of force to break them free any more and you risk breaking the robot.

It only uses 20g of filament and is small enough to fit on a Prusa mini or even a Voron V0.

To add to the #MakerMadness theme I have added some accessory, because what says "spring" more than a robot wearing sunglasses and holding a flower 😁.

Link to the Rock version:
https://thangs.com/mythangs/file/55887

Print Settings:

No support!
No brim!

The point of the Benchmark Bot is to find the best parameters to make it function, therefore it is difficult to recommend any settings.

That being said, I used the following parameters:
0.4mm nozzle, 0.2mm layer height, PLA, 3 walls, 4 top/bottom layers, 10% infill.

Benchmark Bot

Move over boat, there is a new benchmark in town.

This robot is not only a fun print-in-place figure but it is also a very useful calibration tool.

The robot is designed with 17 functional joints with different orientations, couplings, and tolerances. The tolerances range from 0.2 - 0.5mm and allow you to test the minimum clearances your printer can produce and still achieve print-in-place movement.

Each limb is labeled with the tolerances of their joints and all other joints have a 0.3mm tolerance. It might take a little (just a little) bit of force to break them free any more and you risk breaking the robot.

It only uses 20g of filament and is small enough to fit on a Prusa mini or even a Voron V0.

Benchmark Bot (Kazi Toad)

Benchmark Bot Flower

Benchmark_Bot_sunglasses_KaziToad.stl

watering can

These files are for Personal Use Only. If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad

Here is vase number 7, it is a unique twisting and crossing pattern. 

It is specifically designed to be printed in spiral vase mode, printing with one continuous outer wall, to print quickly, without a seam and no support.

I suggest using a large nozzle, line width, and layer height. I also suggest printing in spiral vase mode with 4 bottom layers and only 1 outer wall.

If you like this, take a look at my other models :)

Twisted cross Vase (Vase No. 7)

Here is vase number 7, it is a unique twisting and crossing pattern. 

It is specifically designed to be printed in spiral vase mode, printing with one continuous outer wall, to print quickly, without a seam and no support.

I suggest using a large nozzle, line width, and layer height. I also suggest printing in spiral vase mode with 4 bottom layers and only 1 outer wall.

If you like this, take a look at my other models :)

These files are for Personal Use Only. If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad

This is a semi-realistic Christmas tree that can be illuminated with an ELECTRIC tealight (no flames please).

The best part is: it can be printed in vase mode, that means no support, no seams, thin walls for illumination, and it prints super fast.

The tree is 75 x 120mm, with a 40mm hole in the bottom. Feel free to scale it up or down to fit your needs.
Print with spiral vase mode.

Suggested settings:
- 5 bottom layers
- 0 top layer
- 0.2mm layer height
- 0.6 line width

Checkout my geometric tree [here](https://thangs.com/designer/Kazi%20Toad/3d-model/Vase%20Mode%20Christmas%20tree-38831?manualModelView=true).

Tealight Christmas tree

This is a semi-realistic Christmas tree that can be illuminated with an ELECTRIC tealight (no flames please).

The best part is: it can be printed in vase mode, that means no support, no seams, thin walls for illumination, and it prints super fast.

The tree is 75 x 120mm, with a 40mm hole in the bottom. Feel free to scale it up or down to fit your needs.
Print with spiral vase mode.

Suggested settings:
- 5 bottom layers
- 1 top layer
- 0.2mm layer height
- 0.6 line width

**Hi, I'm Kazi Toad!**

I have a passion for designing things on the border between fun and functional.

Become a Kazi Toad member to receive access to **Premium Models** and a **Commercial License** to sell prints made from my designs.

Let me know if you have any questions: kazitoadprints@gmail.com

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

<div class="markdown">Hi, I&#x27;m Kazi Toad!
I have a passion for designing things on the border between fun and functional.
Become a Kazi Toad member to receive access to Premium Models and a Commercial License to sell prints made from my designs.
Let me know if you have any questions: <a href="mailto:kazitoadprints@gmail.com" target="_blank" rel="noopener nofollow">kazitoadprints@gmail.com</a></div>