A version of the Medium mini painting handle for magnetised 25x25mm square bases like the GreenStuffWorld mdf bases with 5mm magnets in the center.

Medium Mini Painting Handle for 25x25mm Square Bases with Magnets

Mini.Painting.Handle.for.25x25mm.square.bases.Medium.5x2mm.Magnet.stl

Gridfinity tray for DIP package IC's. The bottom is completely flat and there is no magnet holes to make more room for the chips.

Fits 9 DIP28 chips like the Arduino ATMEGA328p or lots of DIP8 chips like the NE555 or 18 DIP14.

Gridfinity Dip IC Tray (1x2x2)

Gridfinity.1x2x2.Dip.Tray.stl

Small Gridfinity tray for DIP package IC's. The bottom is completely flat and there is no magnet hole to make more room for the chips.

Fits 4 DIP28 chips like the Arduino ATMEGA328p or 4x4 pcs of DIP8 chips like the NE555 or 8 DIP14. 

Gridfinity Dip IC Tray (1x1x2)

Gridfinity.Dip.Tray.stl

Gridfinity 1x1x6 USB Cable Bin with 3 Compartments for small USB cables. Cables need to be relatively thin and short to fit.

No magnets holes and a thin bottom to make them deeper and make more room for the cables.

Gridfinity 1x1 USB Cable Bin with 3 Compartments for small cables (thin bottom, no magnets)

Gridfinity 1x1 USB Cable Bin with 3 Compartments.stl

Gridfinity 1x2x3 bin for Bambu Lab A1 nozzles.

There are no magnet holes in the bottom to make better room for the nozzles.

Includes two versions, one with sides for stacking and one without.

Gridfinity bin for 2 Bambu Lab A1 Nozzles

Bambu A1 Nozzle Bin.step

I wanted a thinner health dial and one where the First digit plate fit inside the second digit, on the same "level". I also wanted all the unused numbers to be covered, so there is no confusion.

The first digit plate has a version with a 0 and one without.

Optimized for 0.2mm layerheight and 0.4mm nozzle but the digits will be sharper with a 0.2mm nozzle. 
Switch filament for the last 3 layers of the digit plates to make the numbers stand out.
No support required.

V3: Middle plate (Middle.Plate.v2) has been adjusted to put less pressure on the top cover and make the second digit plate fit better and wobble less.

Health Dial V2 (0-49)

Second.Digit.Plate.step

First.Digit.Plate.No.Zero.step

First.Digit.Plate.No.Zero.stl

Gridfinity 1x3x9 bin with 6 compartments, 2 medium and 4 small ones compartments for those smaller usb cables.

The bottom is hollow with no magnet holes to make more space for the cables and so it uses less filament.

Gridfinity 6 Compartment USB Cable Bin (hollow bottom for space)

Gridfinity.1x3x9.2+4.Compartments.Cable.Bin.stl

Gridfinity 1x1x2 for 3 big usb sticks.

I have some old and oddly Chunky usb dongles, they wont fit if they are too close to other usb thingies, so I made this special holder for 3 of them.

The fit for the USB plug is no snug but not loose either. I have one USB plug that is a bit thicker than the others, that one fits but its a bit tight.

No bottom holes for magnets.

Gridfinity 1x1 USB Device Holder for 3 Chunky Devices

Gridfinity.1x1.USB.Device.Holder.3.Big.Ones.stl

Gridfinity 1x1x2 for 5 small and 2 big usb devices. 

Sometimes USB sticks are just too big to sit next to other usb devices or they stick out over the edge og the bin, so I made room for 2 big ones next to the row of 5 small.

The fit for the USB plug is no snug but not loose either. I have one USB plug that is a bit thicker than the others, that one fits but its a bit tight.

No bottom holes for magnets.

Gridfinity 1x1 USB Device Holder 5 Small + 2 Big Devices

Gridfinity.1x1.USB.Device.Holder.5.Small 2.Big.step

Gridfinity 1x1x2 for 5 small and 4 medium sized usb devices. 
I moved the 5 slot row for small devices closer to the edge to make more room for the 4 devices in the 4 slot row for medium USB devices.

The fit for the USB plug is not snug but not loose either. I have one USB plug that is a bit thicker than the others, that one fits but its a bit tight.

No bottom holes for magnets.

Gridfinity 1x1 USB Device Holder for 5 Small and 4 Medium devices

Gridfinity.1x1.USB.Device.Holder.5.Small.4.Medium.step

Gridfinity 1x1x2 for 10 small usb devices. Can also fit 6 medium size usb sticks.

The fit for the USB plug is no snug but not loose either. I have one USB plug that is a bit thicker than the others, that one fits but its a bit tight.

No bottom holes for magnets.

Gridfinity 1x1 USB Device Holder for 10 Small devices

Gridfinity.1x1.USB.Device.Holder.10.Small.step

Gridfinity 1x3x9 bin with 4 compartments for medium length USB cables and the like.

The bottom is hollow with no magnet holes to make more space for the cables and so it uses less filament.

Gridfinity 4 Compartment USB Cable Bin (hollow bottom for space)

Gridfinity.1x3x9.4.Dividers.Cable.Bin.stl

Number Dial for keeping track of health/points/energy in board games. With the new 1st digit plate, it can represent numbers from 0 to 49.

There is an optional cover for the first digit plate. The 2nd digit cover has a version with guide holes for the 1st digit cover, so its easier to glue it in place.

The first digit plate has two versions; one with and one without the zero.

Optimized to be printed with 0.2mm layer height and a 0.4mm nozzle.

All parts can be printed without support if oriented correctly.

The number plates  can be printed in two colors, switch filament for the last 3 layers (0.2mm layer height) to make the numbers stand out.



Health Dial (0-49)

Second.Digit.Plate.stl

Small and Medium sized handle for mini painting with swappable magnet bases.
Made for 5x2mm magnets. The Medium sized one is inspired by the Citadel Painting Handle Mk2.

Blu Tack the minis on to the bases and swap them out easily when painting many at the same time.

There are two versions of the mini base, the thick version is easier to grip when swapping out the mini, the thin one uses less pla. The slots in the top of the base make the Blu Tack stick better, but there are versions without the slots too.

There are two versions of the handle, one has same diameter top as the mini bases, the other has narrower top for easier base swap. 

Small and Medium Mini Painting Handle with Swappable Magnet Bases

Mini.Painting.Handle.5x2mm.Magnet.stl

28mm.Figure.Base.5x2mm.Magnet.No.Slots.step

28mm.Figure.Base.5x2mm.Magnet.No.Slots.stl

28mm.Figure.Base.5x2mm.Magnet.Thin.No.Slots.stl

28mm.Figure.Base.5x2mm.Magnet.Thin.No.Slots.step

Mini.Painting.Handle.Medium.5x2mm.Magnet.step

Mini.Painting.Handle.Medium.5x2mm.Magnet.stl

Tamiya Cement Holder for Hobbyzone Paint Station.
Screw it on to the paint rack to keep it securely in place.

The fit is very snug, to make it impossible to knock the gule bottle over. If the "manual" is still wrapped around your bottle you should open it and cut it off with a pair of scissors.

Made a bolt with a wider head for the 36mm Paint Station. It is untested but it should work.

There is a 6mm hole for an allen key to help skrew the bolt in from above.




Tamiya Cement Holder for Hobbyzone Paint Station

Tamiya.Cement.Holder.v1.stl

A handle to hold the minis when you spray prime them.

Shaped for 25mm (1 inch) bases so you can spray prime them from beneath.
Attach minis with BlueTack or double sided tape.

The handle can be unscrewed from the rail, so you can switch to another set of minis and set the first batch to dry.

If you dont want to unscrew the handle, you can put it in a heavy mug, so it wont fall over while the minis are drying.

I might do a longer rail for 9 or 11 minis and maybe a magnet system for connecting the handle. Maybe even one with magnets on the rail, if you have magnets on the bases of your minis.

I printed the rail and the connector with 0.12mm layerheight and the handle in 0.2mm.

If the theads are too tight/loose, you can scale the connector down/up a bit to get a good fit.

v2: I rotated the handle threads a bit, so the handle and rail will be better balanced when leaning against the side of a cup when you place the handle in a cup while the minis dry.

v3 Added a rail for 9 minis.
v4 Added rails for 3 anf 5 minis.
     Added versions of rails without slots for better bed adhesion. Blu Tack makes the models stick just fine without the slots.

Priming Handle for Minis

Priming.Handle.v1.stl

Priming.Handle.Connector.v1.stl

Priming.Handle.Slotted.Rail.9.Minis.v1.step

Priming.Handle.Slotted.Rail.9.Minis.v1.stl

Priming.Handle.Rail.3.Minis.v1.stl

Priming.Handle.Rail.3.Minis.v1.step

Priming.Handle.Slotted.Rail.3.Minis.v1.step

Priming.Handle.Slotted.Rail.3.Minis.v1.stl

Priming.Handle.Rail.7.Minis.v1.stl

Priming.Handle.Rail.7.Minis.v1.step

Priming.Handle.Rail.9.Minis.v1.step

Priming.Handle.Rail.9.Minis.v1.stl

Priming.Handle.Rail.5.Minis.v1.stl

Priming.Handle.Rail.5.Minis.v1.step

Priming.Handle.Slotted.Rail.5.Minis.v1.step

Priming.Handle.Slotted.Rail.5.Minis.v1.stl

Tray for 12 15 or 18 Armypainter bottles that you can stack on top of eachother.

The feet screw on and are only needed for the upper trays since the top of the bottles on the bottom tray slots in to the feet on the top tray.

I made 3 different feet, but prefer the 'Octa' one, it matches the style of the tray.

With a tray upside down on top of the bottles and a couple of rubberbands, they keep everythin in place for transport.

Onshape CAD model:
https://cad.onshape.com/documents/aba5b84ea1bb2822acfd0eb2/w/0eab23ed1893b8bbaacc57d4/e/544cb9884b5d28b205af309b?renderMode=0&uiState=65ad63ac49d4b7366f7576eb

Inspired by https://www.thingiverse.com/thing:4696460


Army Painter Stackable Tray

Army.Painter.Stackable.Tray.15.Bottles.v3.3.stl

Army.Painter.Stackable.Tray.12.Bottles.v3.4.stl

Army.Painter.Stackable.Tray.18.Bottles.stl

Army.Painter.Stackable.Tray.18.Bottles.step

Army.Painter.Stackable.Tray.15.Bottles.step

Army.Painter.Stackable.Tray.12.Bottles.step

Round.Foot.v3.4.step

Hex.Foot.v3.4.step

Octa.Foot.v3.4.step

For organizing when playing board games.
 
Compatible with the Tabletop Tiles.

Magnet holes are for 5x2mm magnets.


Tabletop Tile Shard

Tabletop.Tile.Shard.v1.4.stl

A counting device for health and XP in Gloomhaven or Health and Stamina in Imperial Assault or Descent.

All the 'Foot' files are for the left side, if you want a right hand side, you just mirror one in your slicer.

I liked the look and feel of Scottimus' Life (or anything) Counter, but I disliked the clip for holding it together and the cylindrical part is annoying to print and completely unnecessary, so i redesiged the entire thing.

The peg that holds it all together can be printed in different lengths to make room for 2, 3, 5 or 2 and 2 with a middle section to separate the numbers. I also made some 1 mm spacers to get some space between the sides and the number rings.

Once assembled it can be taken apart again and reassembled in a different configuration with a central peg with a different length.

The Middle section has the same width as the number rings, so you can swap it for a number ring if you dont want it.

I made my design on Onshape:
https://cad.onshape.com/documents/b2006b51bb805ecd3b621795/w/e2bdb640d57a3792caf8e1d6/e/7bbd7c8935b1bea6f009a6eb?configuration=SpringDiameter%3D0.021%2Bmeter

You can sign up for free and fork it if you want to change something.

Remixed from 
Life (or anything) counter for table-top games
https://www.thingiverse.com/thing:3351902

Life + XP Counter (Gloomhaven)

Counter.Foot.Left.Health.Icon.Rebel.Logo.v1.2.stl

A splintered and holed table for the Gloomhavn boardgame.

I wanted a table suitable for a thieves den, one that looks cheap ill maintained.

If you print it with the surfuce up, you need to use support.

Alternatively you can print it upside down but be careful you dont squash the first layer, that will wash out the surface details. Conversely if you have too much distance between nozzle and build plate, the fine details will come loose and the table surface wont be as nice looking.

I added the option for printing the legs and the table top separately, so no support will be needed and the surface pattern can be facing up for the best result. You just have to use a little glue.

The CAD model can be found on Onshape:
https://cad.onshape.com/documents/9c1e818ea825a9dfcf08dfdc/w/f51d5551fa44e4d7906b34a5/e/22840ec1b0cfabc0875c6b58

Gloomhaven Table

Table.for.Gloomhaven.v1.stl

Solid or open model with separate lid that fits the bottom.

Sarcophagus for Gloomhaven

Sarcophagus.for.Gloomhaven.solid.v1.2.stl

Inspired by Wyrmwoodgaming's wooden tiles.

I wanted some Tabletop Tiles style trays that are deeper than the others so stuff actually fits in there. 

There are tiles with 1, 2, 3 and 4 compartments.

I dropped the coaster feature, since its not needed and it is annoying to print. The bottom is only 2mm thick, making the compartments 14,2mm deep.

I Also wanted smaller magnets, since the 10mm magnets are more expensive and not necessary. 5x2mm magnets are fine.

I uploaded models without top and bottom magnet holes and models without magnet holes at all. Its a nice gimmick, but you probably wont need the magnets and the compartments are even wider on the models with no magnets.

Deeper Tabletop Tiles with small magnets

3.Compartment.Tabletop.Tile.5x2mm.top.bottom.side.magnet.holes.stl

Prints on its side. Use the "Lay Flat" function in Cura.
Needs no support.

Shaving Brush Stand

Shave.Brush.Stand.v1.5.stl

A block for the tracksaw clamp, so it can be used to clamp wood without marring the surface with the metal part of the jaw.

Should fit the Makita Ratchet Guide Rail Clamps.

Fits the rachet clamps from Temu and should also fit the VEIKO clamps from Banggood.

https://www.temu.com/dk-en/1pc-ratchet-table-clamp-quick-release-bar-clamp-steel-clamping-f-track-clip-for-hole-table-and-guide-rail-system-woodworking-tool-g-601099529252564.html?top_gallery_url=https%3A%2F%2Fimg.kwcdn.com%2Fproduct%2FFancyalgo%2FVirtualModelMatting%2F7a0a2edc0bd3ea174f803e741ea20fef.jpg&spec_gallery_id=4045002608&refer_page_sn=10009&refer_source=0&freesia_scene=2&_oak_freesia_scene=2&_oak_rec_ext_1=MjEwMjA&search_key=ratchet%20clamp&refer_page_el_sn=200049&refer_page_name=search_result&refer_page_id=10009_1700686982698_6rqhdxxk8k&_x_sessn_id=iaapfr0dij

https://usa.banggood.com/VEIKO-2PCS-Alloy-Steel-Upgrade-Quick-Ratchet-Track-Saw-Guide-Rail-Clamp-MFT-Clamp-for-MFT-Table-and-Guide-Rail-System-Woodworking-Clamp-reviews-p1894619.html 

Helo

Achievements

Seedling

Explorer

Fan Favorite

Pinned models

Life + XP Counter (Gloomhaven)

Priming Handle for Minis

Small and Medium Mini Painting Handle with Swappable Magnet Bases

Health Dial V2 (0-49)

Medium Mini Painting Handle for 25x25mm Square Bases with Magnets

Gridfinity Dip IC Tray (1x2x2)

Gridfinity Dip IC Tray (1x1x2)

Gridfinity 1x1 USB Cable Bin with 3 Compartments for small cables (thin bottom, no magnets)

Gridfinity bin for 2 Bambu Lab A1 Nozzles

Health Dial V2 (0-49)

Gridfinity 6 Compartment USB Cable Bin (hollow bottom for space)

Gridfinity 1x1 USB Device Holder for 3 Chunky Devices

Gridfinity 1x1 USB Device Holder 5 Small + 2 Big Devices

Gridfinity 1x1 USB Device Holder for 5 Small and 4 Medium devices

Gridfinity 1x1 USB Device Holder for 10 Small devices

Gridfinity 4 Compartment USB Cable Bin (hollow bottom for space)

Health Dial (0-49)

Small and Medium Mini Painting Handle with Swappable Magnet Bases

Tamiya Cement Holder for Hobbyzone Paint Station

Priming Handle for Minis

Army Painter Stackable Tray

Tabletop Tile Shard

Life + XP Counter (Gloomhaven)

Gloomhaven Table

Sarcophagus for Gloomhaven

Deeper Tabletop Tiles with small magnets

Shaving Brush Stand

Ratchet Clamp Block